Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
Two parallel shafts are 200 mm apart. They must be connected by a pair of spur gears with a module of 5 mm and a speed reduction of 4 : 1. How many teeth N1 must the pinion have?
An open belt connects a 125 mm driving pulley at 960 rpm to a 400 mm pulley; the centres are 800 mm apart. The coefficient of friction is 0.3 and the tight-side tension may not exceed 1200 N. Find the largest power P the belt can transmit without slipping, in kW (ignore centrifugal effects).
A hollow steel shaft (outer diameter 40 mm, inner diameter 28 mm, length 2.5 m) is fixed at one end and twisted by a torque of 200 N·m at the other. Find the angle of twist φ in degrees.
A solid steel shaft of diameter 25 mm is fixed to rigid walls at both ends A and B. A torque of 500 N·m is applied at C, 1 m from A and 0.5 m from B. Find the maximum shear stress τmax in the shaft.
A point in a loaded part has σₓ = 130 MPa, σᵧ = 110 MPa and τₓᵧ = −20 MPa (tension positive). Find the maximum in-plane shear stress τmax.
A point in a loaded part has σₓ = −50 MPa, σᵧ = 50 MPa and τₓᵧ = −60 MPa (tension positive). Find the shear stress τθ on a plane whose normal is rotated 60° counter-clockwise from the x-axis (positive in the same sense as τₓᵧ).
Find the elongation δ of the steel bar under the axial load.
The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.
A column of length L made of steel is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.
A solid round column of length L made of aluminium is fixed at the base and pinned at the top. It must carry 115 kN with a factor of safety of 2 against buckling. Find the smallest diameter d.
A 50 kg mass on a spring with a stiffness of 20 kN/m has a viscous damper giving a damping ratio of 0.6. Find the damped natural frequency fd of its free vibration in Hz.
A 25 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 15 kN/m and k₂ = 10 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: N1 = 16
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: P = 4.281 kW
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: φ = 1.875 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: τmax = 108.6 MPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω. When both ends are fixed, statics alone gives only TA + TB = T₀; the second equation is compatibility (equal twist of both parts at the loaded section).
The larger of the two torques governs (same diameter).
Answer: τmax = 22.36 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: τθ = 73.3 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: δ = 2.763 mm
Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).
E for steel = 200 GPa = 200000 MPa.
Answer: δ = 1.415 mm
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
Answer: Pcr = 37.85 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: d = 95.47 mm
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Check: the slenderness KL/r is 146.6, so the column is slender and Euler applies.
Answer: fd = 2.546 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 25 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/machine-design