Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 2.2 kW motor running at 960 rpm drives a pinion with 18 teeth, which meshes with a gear with 32 teeth. The gear pair has an efficiency of 96%. Find the output torque T2 on the gear shaft.
A 1.5 kW motor at 960 rpm drives gear A (16 teeth), which meshes with gear B (45 teeth). Gear C (18 teeth) on the same shaft as B drives gear D (24 teeth) on the output shaft. Each gear mesh has an efficiency of 97%. Find the output torque Tout.
A hollow shaft must carry a torque of 750 N·m. Its inner diameter is to be 0.8 times its outer diameter, and the shear stress must not exceed 40 MPa. Find the smallest outer diameter do.
A solid aluminium shaft transmits 20 kW at 300 rpm. The shear stress must not exceed 40 MPa and the twist must not exceed 0.5° per m of length. Find the smallest diameter d that satisfies both limits.
A point has σₓ = 120 MPa, σᵧ = 30 MPa and τₓᵧ = −10 MPa (tension positive). Find the angle θs, between −90° and 90°, from the x-axis to the normal of the plane on which the shear stress has its maximum positive value +R (shear positive in the same sense as τₓᵧ).
A point in a loaded part has σₓ = −60 MPa, σᵧ = 90 MPa and τₓᵧ = 30 MPa (tension positive). Find the shear stress τθ on a plane whose normal is rotated 25° counter-clockwise from the x-axis (positive in the same sense as τₓᵧ).
Find the elongation δ of the steel bar under the axial load.
The stepped bar is fixed at the wall and loaded at its free end. Find the largest normal stress σmax in the bar.
A column of length L made of steel is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of steel is fixed at the base and free at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
A 15 kg mass on a spring with a stiffness of 50 kN/m has a viscous damper giving a damping ratio of 0.3. Find the damped natural frequency fd of its free vibration in Hz.
A 5 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 60 kN/m and the lower one k₂ = 12 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: T2 = 37.35 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: Tout = 52.65 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: do = 54.48 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
A solid shaft would need d = 45.71 mm; the hollow one is a little larger but much lighter.
Answer: d = 73.12 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Both limits must hold, so the larger diameter governs.
Here stiffness governs.
Answer: θs = −51.26 °
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
On Mohr’s circle the top point (+R) is 90° from the principal point σ₁; on the element that is 45°.
Positive angles are counter-clockwise.
Answer: τθ = 76.74 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: δ = 1.171 mm
Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).
E for steel = 200 GPa = 200000 MPa.
Answer: σmax = 265.3 MPa
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
The thinner segment has the smaller area, so it carries the larger stress.
Answer: Pcr = 139.5 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: σcr = 111 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: fd = 8.766 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 7.118 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/machine-design