Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
An 11 kW motor running at 2900 rpm drives a pinion with 25 teeth and a module of 2.5 mm. Find the tangential force Ft on the pinion teeth.
In a compound gear train, gear A (36 teeth) on the input shaft turns at 1500 rpm and drives gear B (50 teeth). Gear C (40 teeth) is fixed to the same shaft as B and drives gear D on the output shaft. The output must turn at 600 rpm. How many teeth ND must gear D have?
A solid aluminium shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.
A solid steel shaft of diameter 60 mm is fixed to rigid walls at both ends A and B. A torque of 500 N·m is applied at C, 2.5 m from A and 2 m from B. Find the maximum shear stress τmax in the shaft.
A point has σₓ = 140 MPa, σᵧ = −30 MPa and τₓᵧ = 40 MPa (tension positive). Find the angle θs, between −90° and 90°, from the x-axis to the normal of the plane on which the shear stress has its maximum positive value +R (shear positive in the same sense as τₓᵧ).
A solid shaft of diameter 40 mm carries an axial tensile force of 60 kN together with a torque of 250 N·m. At the surface of the shaft, find the largest principal stress σ1.
Find the axial strain ε in the copper bar, in microstrain (µε = 10⁻⁶).
The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.
A column of length L made of aluminium is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of steel is fixed at the base and pinned at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
In a free-vibration test of a damped mass–spring system, a displacement peak of 30 mm is followed one cycle later by a peak of 16 mm. Find the damping ratio ζ.
A 20 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 30 kN/m and the lower one k₂ = 5 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: Ft = 1159 N
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: ND = 72
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: φ = 14.03 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: τmax = 6.55 MPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω. When both ends are fixed, statics alone gives only TA + TB = T₀; the second equation is compatibility (equal twist of both parts at the loaded section).
The larger of the two torques governs (same diameter).
Answer: θs = −32.4 °
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
On Mohr’s circle the top point (+R) is 90° from the principal point σ₁; on the element that is 45°.
Positive angles are counter-clockwise.
Answer: σ1 = 54.95 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: ε = 4897 µε
Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).
E for copper = 117 GPa = 117000 MPa.
Answer: δ = 2.291 mm
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
Answer: Pcr = 47.16 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: σcr = 179 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: ζ = 0.09955
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 2.33 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/machine-design