Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 160 mmd2​ = 315 mm960 rpmT1​ = 500 NT2​ = 125 NP = ?

A belt runs on a 160 mm driving pulley at 960 rpm. The tension is 500 N on the tight side and 125 N on the slack side. Find the power P transmitted, in kW.

d1 = 160 mmn1 = 960 rpmT1 = 500 NT2 = 125 N
P = kW
2.Gears & gear trainsHard
d1​ = 100 mmd2​ = 450 mm1500 rpmC = 800 mmθ = ?

An open belt connects a 100 mm pulley and a 450 mm pulley whose centres are 800 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.

d1 = 100 mmd2 = 450 mmC = 800 mm
θ = °
3.Torsion of shaftsMedium
d = ?T = 1000 N·mL = 0.8 m

A solid aluminium shaft 0.8 m long carries a torque of 1000 N·m. The angle of twist between its ends must not exceed 3°. Find the smallest diameter d that meets this limit.

T = 1000 N·mL = 0.8 mG = 26 GPaφallow = 3°
d = mm
4.Torsion of shaftsHard
Td = ?

A solid shaft must transmit 30 kW at 3000 rpm without the shear stress exceeding 50 MPa. Find the smallest diameter d that works.

P = 30 kWN = 3000 rpmτallow = 50 MPa
d = mm
5.Mohr’s circle & stress transformationMedium
σx​ = 120σy​ = −40τxy​ = 10MPa

A point has σₓ = 120 MPa, σᵧ = −40 MPa and τₓᵧ = 10 MPa (tension positive). Find the angle θs, between −90° and 90°, from the x-axis to the normal of the plane on which the shear stress has its maximum positive value +R (shear positive in the same sense as τₓᵧ).

σx = 120 MPaσy = −40 MPaτxy = 10 MPa
θs = °
6.Mohr’s circle & stress transformationHard
σx​ = 30σy​ = −40τxy​ = 60MPa

A point in a loaded part has σₓ = 30 MPa, σᵧ = −40 MPa and τₓᵧ = 60 MPa (tension positive). Find the shear stress τθ on a plane whose normal is rotated 30° clockwise from the x-axis (positive in the same sense as τₓᵧ).

σx = 30 MPaσy = −40 MPaτxy = 60 MPaθ = -30°
τθ = MPa
7.Axial stress & strainMedium
Ø 30 mmCopper2.5 mP = 105 kN

Find the elongation δ of the copper bar under the axial load.

P = 105 kNd = 30 mmL = 2.5 mE = 117 GPa
δ = mm
8.Axial stress & strainHard
Ø 40 mmBrass1.5 mØ 16 mmAluminium1 mP = 80 kN

The stepped bar is fixed at the wall and loaded at its free end. Find the largest normal stress σmax in the bar.

P = 80 kNsegment 1: Ø40 mm, 1.5 m, brass (E = 100 GPa)segment 2: Ø16 mm, 1 m, aluminium (E = 70 GPa)
σmax = MPa
9.Column bucklingMedium
PL = 4 md = 25 mmcross-section

A column of length L made of steel is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 4 mE = 200 GPa (steel)d = 25 mm
Pcr = kN
10.Column bucklingHard
PL = 5 md = 50 mmcross-section

A column of length L made of aluminium is fixed at the base and free at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 5 mE = 70 GPa (aluminium)d = 50 mm
σcr = MPa
11.Mechanical vibrationsMedium
tx40 mm1 cycle21.3 mm

In a free-vibration test of a damped mass–spring system, a displacement peak of 40 mm is followed one cycle later by a peak of 21.3 mm. Find the damping ratio ζ.

x0 = 40 mmx1 = 21.3 mmn = 1
ζ =
12.Mechanical vibrationsHard
k1​ = 100k2​ = 20m = 10 kg

A 10 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 100 kN/m and the lower one k₂ = 20 kN/m. Find the equivalent stiffness keq of the spring system in kN/m.

m = 10 kgk1 = 100 kN/mk2 = 20 kN/m
keq = kN/m

3Solutions

1.Gears & gear trains

Answer: P = 3.016 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt speed

v = 8.042 m/s

Power

P = (500 − 125)·8.042 = 3016 W = 3.016 kW

Answer

P = 3.016 kW
2.Gears & gear trains

Answer: θ = 154.7 °

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt angle

asin(0.2188) = 12.64°

Angle of wrap

θ = 180 − 2·12.64 = 154.7°

Answer

θ = 154.7°
3.Torsion of shafts

Answer: d = 49.46 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Required polar moment

T = 1000 N·m = 1 × 10⁶ N·mm
L = 0.8 m = 800 mm
G = 26 GPa = 26000 MPa
φ = 3·π/180 = 0.05236 rad
J = TL/(Gφ) = 1 × 10⁶·800/(26000·0.05236) = 587649 mm⁴

Diameter

d = (32J/π)1/4 = 49.46 mm

Answer

d = 49.46 mm

In practice you would round up to the next standard size.

4.Torsion of shafts

Answer: d = 21.35 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Torque

ω = 2πN/60 = 2π·3000/60 = 314.2 rad/s
T = P/ω = 30000/314.2 = 95.49 N·m

Diameter from the allowable stress

d = ∛(16T/(π·τallow)) = ∛(16·95493/(π·50)) = 21.35 mm

Answer

d = 21.35 mm

In practice you would round up to the next standard size.

5.Mohr’s circle & stress transformation

Answer: θs = −41.44 °

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCτmax​

Angle on the circle

On Mohr’s circle the top point (+R) is 90° from the principal point σ₁; on the element that is 45°.

cos 2θs = 10/80.62 = 0.124, sin 2θs = −80/80.62 = −0.9923
2θs = atan2(−80, 10) = −82.87°

Angle on the element

θs = −41.44°
check: θs − θp = −41.44 − 3.563 = −45°

Answer

θs = −41.44°

Positive angles are counter-clockwise.

6.Mohr’s circle & stress transformation

Answer: τθ = 60.31 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Transformation equation

τθ = −35·−0.866 + 60·0.5 = 60.31 MPa

Answer

τθ = 60.31 MPa
7.Axial stress & strain

Answer: δ = 3.174 mm

Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).

Stress

A = π·30²/4 = 706.9 mm²
σ = P/A = 105·1000/706.9 = 148.5 MPa

Strain (Hooke’s law)

E for copper = 117 GPa = 117000 MPa.

ε = σ/E = 148.5/117000 = 0.00127 = 1270 µε

Elongation

δ = ε·L = 0.00127·2500 mm = 3.174 mm

Answer

δ = 3.174 mm
8.Axial stress & strain

Answer: σmax = 397.9 MPa

Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.

Same force in both segments

The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.

A1 = π·40²/4 = 1257 mm², A2 = π·16²/4 = 201.1 mm²
σ1 = 63.66 MPa
σ2 = 397.9 MPa

Largest stress

The thinner segment has the smaller area, so it carries the larger stress.

σmax = 397.9 MPa

Answer

σmax = 397.9 MPa
9.Column buckling

Answer: Pcr = 2.366 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·25⁴/64 = 19175 mm⁴

Effective length

KL = 1·4000 = 4000 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·19175/4000² = 2366 N = 2.366 kN

Answer

Pcr = 2.366 kN
10.Column buckling

Answer: σcr = 1.079 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·50⁴/64 = 306796 mm⁴

Radius of gyration and slenderness

A = 1963 mm²
r = √(I/A) = √(306796/1963) = 12.5 mm
KL = 2·5000 = 10000 mm
KL/r = 10000/12.5 = 800

Critical stress

σcr = π²E/(KL/r)² = π²·70000/800² = 1.079 MPa

Answer

σcr = 1.079 MPa
11.Mechanical vibrations

Answer: ζ = 0.09979

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Logarithmic decrement

δ = (1/1)·ln(40/21.3) = 0.6302

Damping ratio

ζ = δ/√(4π² + δ²) = 0.6302/√(39.48 + 0.3971) = 0.09979

Answer

ζ = 0.09979
12.Mechanical vibrations

Answer: keq = 16.67 kN/m

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.

1/keq = 1/100 + 1/20 → keq = 100·20/(100 + 20) = 16.67 kN/m

Answer

keq = 16.67 kN/m

ExamProblems · examproblems.com/courses/machine-design