Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 100 mmd2​ = 400 mm960 rpmT1​ = 800 NT2​ = 160 NP = ?

A belt runs on a 100 mm driving pulley at 960 rpm. The tension is 800 N on the tight side and 160 N on the slack side. Find the power P transmitted, in kW.

d1 = 100 mmn1 = 960 rpmT1 = 800 NT2 = 160 N
P = kW
2.Gears & gear trainsHard
A = 24B = 40C = 50D = ?

In a compound gear train, gear A (24 teeth) on the input shaft turns at 3000 rpm and drives gear B (40 teeth). Gear C (50 teeth) is fixed to the same shaft as B and drives gear D on the output shaft. The output must turn at 1500 rpm. How many teeth ND must gear D have?

nin = 3000 rpmA = 24B = 40C = 50nout = 1500 rpm
ND =
3.Torsion of shaftsMedium
T = 250 N·md = 30 mmL = 3 mφ = ?

A solid brass shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.

T = 250 N·md = 30 mmL = 3 mG = 39 GPa
φ = °
4.Torsion of shaftsHard
d = 30 mmTB​ = 250 N·mTC​ = 750 N·mABC3 m1.5 m

A solid brass shaft of diameter 30 mm is fixed at A. A torque of 250 N·m acts at B, 3 m from A, and a torque of 750 N·m in the opposite direction acts at the free end C, a further 1.5 m along. Find the maximum shear stress τmax in the shaft.

d = 30 mmTB = 250 N·mTC = 750 N·mAB = 3 mBC = 1.5 m
τmax = MPa
5.Mohr’s circle & stress transformationMedium
σx​ = −60σy​ = 90τxy​ = −60MPa

A point in a loaded part has σₓ = −60 MPa, σᵧ = 90 MPa and τₓᵧ = −60 MPa (tension positive). Find the maximum in-plane shear stress τmax.

σx = −60 MPaσy = 90 MPaτxy = −60 MPa
τmax = MPa
6.Mohr’s circle & stress transformationHard
σx​ = −10σy​ = 70τxy​ = 60MPa

A point in a loaded part has σₓ = −10 MPa, σᵧ = 70 MPa and τₓᵧ = 60 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 20° counter-clockwise from the x-axis.

σx = −10 MPaσy = 70 MPaτxy = 60 MPaθ = 20°
σθ = MPa
7.Axial stress & strainMedium
P = ?12300 mm400 mmØ25Ø40δ = 0.3 mm

A bar is made of a steel segment (diameter 25 mm, length 300 mm, E = 200 GPa) joined end to end with a segment made of aluminium (diameter 40 mm, length 400 mm, E = 70 GPa). It is fixed at one end and pulled at the other. Find the axial load P that stretches it by 0.3 mm in total.

segment 1: steel, Ø25 mm, 300 mm, E = 200 GPasegment 2: aluminium, Ø40 mm, 400 mm, E = 70 GPaδ = 0.3 mm
P = kN
8.Axial stress & strainHard
Ø 25 mmBrass1 mØ 12 mmSteel1.5 mP = 15 kN

The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.

P = 15 kNsegment 1: Ø25 mm, 1 m, brass (E = 100 GPa)segment 2: Ø12 mm, 1.5 m, steel (E = 200 GPa)
δ = mm
9.Column bucklingMedium
PL = 5 md = 25 mmcross-section

A column of length L made of aluminium is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 5 mE = 70 GPa (aluminium)d = 25 mm
Pcr = kN
10.Column bucklingHard
P = 125 kNL = 5 md = ?cross-section

A solid round column of length L made of steel is fixed at both ends. It must carry 125 kN with a factor of safety of 2.5 against buckling. Find the smallest diameter d.

P = 125 kNn = 2.5L = 5 mE = 200 GPa (steel)
d = mm
11.Mechanical vibrationsMedium
k = 50 kN/mc = 220 N·s/mm = 25 kg

A 25 kg mass is supported by a spring with a stiffness of 50 kN/m and a viscous damper with a damping coefficient of 220 N·s/m. Find the damping ratio ζ.

m = 25 kgk = 50 kN/mc = 220 N·s/m
ζ =
12.Mechanical vibrationsHard
k1​ = 20k2​ = 5m = 25 kg

A 25 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 20 kN/m and the lower one k₂ = 5 kN/m. Find the equivalent stiffness keq of the spring system in kN/m.

m = 25 kgk1 = 20 kN/mk2 = 5 kN/m
keq = kN/m

3Solutions

1.Gears & gear trains

Answer: P = 3.217 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt speed

v = 5.027 m/s

Power

P = (800 − 160)·5.027 = 3217 W = 3.217 kW

Answer

P = 3.217 kW
2.Gears & gear trains

Answer: ND = 60

Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.

Intermediate shaft speed

nB = nC = 3000·24/40 = 1800 rpm

Teeth on gear D

ND = C·nC/nout = 50·1800/1500 = 60

Answer

ND = 60
3.Torsion of shafts

Answer: φ = 13.86 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Polar second moment of area

J = π·30⁴/32 = 79522 mm⁴

Angle of twist

φ = TL/(GJ) = 250·1000·3000/(39000·79522) = 0.2418 rad
φ = 0.2418·180/π = 13.86°

Answer

φ = 13.86°
4.Torsion of shafts

Answer: τmax = 141.5 MPa

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Internal torques

Sense of TC taken as positive.

TBC = TC = 750 N·m
TAB = TC − TB = 750 − 250 = 500 N·m

Maximum shear stress

The segment with the largest internal torque has the largest stress (same diameter).

|T|max = 750 N·m
τmax = 16·750000/(π·30³) = 141.5 MPa

Answer

τmax = 141.5 MPa
5.Mohr’s circle & stress transformation

Answer: τmax = 96.05 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCτmax​

Radius of Mohr’s circle

τmax = R = √(((−60 − 90)/2)² + −60²) = 96.05 MPa

Answer

τmax = 96.05 MPa
6.Mohr’s circle & stress transformation

Answer: σθ = 37.93 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Transformation equation

σθ = 30 + −40·0.766 + 60·0.6428 = 37.93 MPa

Answer

σθ = 37.93 MPa
7.Axial stress & strain

Answer: P = 39.46 kN

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

A₁ = 490.9 mm², A₂ = 1257 mm²

Flexibilities

L₁/(E₁A₁) = 300/(200000·490.9) = 3.056 × 10⁻⁶ mm/N
L₂/(E₂A₂) = 400/(70000·1257) = 4.547 × 10⁻⁶ mm/N

Load

P = 0.3/7.603 × 10⁻⁶ = 39458 N = 39.46 kN

Answer

P = 39.46 kN
8.Axial stress & strain

Answer: δ = 1.3 mm

Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.

Same force in both segments

The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.

A1 = π·25²/4 = 490.9 mm², A2 = π·12²/4 = 113.1 mm²
σ1 = 30.56 MPa
σ2 = 132.6 MPa

Add the segment elongations

δ1 = σ1L1/E1 = 30.56·1000/100000 = 0.3056 mm
δ2 = σ2L2/E2 = 132.6·1500/200000 = 0.9947 mm
δ = δ1 + δ2 = 1.3 mm

Answer

δ = 1.3 mm
9.Column buckling

Answer: Pcr = 2.12 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·25⁴/64 = 19175 mm⁴

Effective length

KL = 0.5·5000 = 2500 mm

Critical load

Pcr = π²EI/(KL)² = π²·70000·19175/2500² = 2120 N = 2.12 kN

Answer

Pcr = 2.12 kN
10.Column buckling

Answer: d = 67.01 mm

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Required critical load

Pcr = n·P = 2.5·125000 = 312500 N
KL = 0.5·5000 = 2500 mm

Solve for the diameter

d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·312500·2500²/(π³·200000))^(1/4) = 67.01 mm

Answer

d = 67.01 mm

Check: the slenderness KL/r is 149.2, so the column is slender and Euler applies.

11.Mechanical vibrations

Answer: ζ = 0.09839

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Critical damping

cc = 2·√(k·m) = 2·√(50000·25) = 2236 N·s/m

Damping ratio

ζ = c/cc = 220/2236 = 0.09839

Answer

ζ = 0.09839

ζ < 1, so the system is underdamped and oscillates as it decays.

12.Mechanical vibrations

Answer: keq = 4 kN/m

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.

1/keq = 1/20 + 1/5 → keq = 20·5/(20 + 5) = 4 kN/m

Answer

keq = 4 kN/m

ExamProblems · examproblems.com/courses/machine-design