Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
Nw​ = 45z = 4, 2900 rpm

A worm with 4 start(s) turns at 2900 rpm and drives a worm wheel with 45 teeth. Find the speed nw of the wheel.

z = 4Nw = 45n = 2900 rpm
nw = rpm
2.Gears & gear trainsHard
A = 36B = 50C = 12D = 72

In a compound gear train, gear A (36 teeth) on the input shaft turning at 1500 rpm drives gear B (50 teeth). Gear C (12 teeth) is fixed to the same shaft as B and drives gear D (72 teeth) on the output shaft. Find the output speed nout.

nin = 1500 rpmA = 36B = 50C = 12D = 72
nout = rpm
3.Torsion of shaftsMedium
do​ = ?T = 2000 N·m

A hollow shaft must carry a torque of 2000 N·m. Its inner diameter is to be 0.8 times its outer diameter, and the shear stress must not exceed 75 MPa. Find the smallest outer diameter do.

T = 2000 N·mdi/do = 0.8τallow = 75 MPa
do = mm
4.Torsion of shaftsHard
d = ?50 kW, 750 rpm

A solid brass shaft transmits 50 kW at 750 rpm. The shear stress must not exceed 40 MPa and the twist must not exceed 1° per m of length. Find the smallest diameter d that satisfies both limits.

P = 50 kWN = 750 rpmτallow = 40 MPaθallow = 1°/mG = 39 GPa
d = mm
5.Mohr’s circle & stress transformationMedium
σx​ = 120σy​ = −50τxy​ = 10MPa

A point in a loaded part has σₓ = 120 MPa, σᵧ = −50 MPa and τₓᵧ = 10 MPa (tension positive). Find the maximum in-plane shear stress τmax.

σx = 120 MPaσy = −50 MPaτxy = 10 MPa
τmax = MPa
6.Mohr’s circle & stress transformationHard
35°D = 600 mm, t = 12 mm, p = 2 MPap

A thin-walled cylindrical tank of inner diameter 600 mm and wall thickness 12 mm holds gas at a gauge pressure of 2 MPa. It is made from plate welded along a helical seam at 35° to the axis of the cylinder. Find the normal stress σn acting across the weld seam.

D = 600 mmt = 12 mmp = 2 MPaα = 35°
σn = MPa
7.Axial stress & strainMedium
Ø 10 mmCopper1 mP = 100 kN

Find the axial strain ε in the copper bar, in microstrain (µε = 10⁻⁶).

P = 100 kNd = 10 mmL = 1 mE = 117 GPa
ε = µε
8.Axial stress & strainHard
P = ?Ø30120 GPaØ80/60800 mm

A steel rod (diameter 30 mm, E = 200 GPa, allowable stress 150 MPa) sits inside a tube made of copper (outer diameter 80 mm, inner diameter 60 mm, E = 120 GPa, allowable stress 60 MPa). They are compressed together between rigid plates. Find the largest load Pmax.

rod: Ø30 mm, E = 200 GPa, σallow = 150 MPatube: Ø80/Ø60 mm, E = 120 GPa, σallow = 60 MPa
Pmax = kN
9.Column bucklingMedium
PL = 1.5 md = 50 mmcross-section

A column of length L made of aluminium is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.

L = 1.5 mE = 70 GPa (aluminium)d = 50 mm
Pcr = kN
10.Column bucklingHard
PL = 1.5 md = 40 mmcross-section

A column of length L made of steel is fixed at the base and free at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 1.5 mE = 200 GPa (steel)d = 40 mm
σcr = MPa
11.Mechanical vibrationsMedium
tx20 mm3 cycles4.4 mm

In a free-vibration test of a damped mass–spring system, a displacement peak of 20 mm is followed 3 cycles later by a peak of 4.4 mm. Find the damping ratio ζ.

x0 = 20 mmx3 = 4.4 mmn = 3
ζ =
12.Mechanical vibrationsHard
k1​ = 40k2​ = 40k3​ = 10m = 25 kg

A 25 kg mass hangs from spring k₃ = 10 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 40 kN/m and k₂ = 40 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.

m = 25 kgk1 = 40 kN/mk2 = 40 kN/mk3 = 10 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: nw = 257.8 rpm

Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.

Wheel speed

nw = n·z/Nw = 2900·4/45 = 257.8 rpm

Answer

nw = 257.8 rpm
2.Gears & gear trains

Answer: nout = 180 rpm

Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.

First stage

nB = 1500·36/50 = 1080 rpm = nC

Second stage

nout = 1080·12/72 = 180 rpm

Answer

nout = 180 rpm

total ratio = 8.333 : 1

3.Torsion of shafts

Answer: do = 61.27 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Outer diameter from the allowable stress

T = 2000 N·m = 2 × 10⁶ N·mm
1 − k⁴ = 1 − 0.8⁴ = 0.5904
do = ∛(16T/(π·τallow·(1 − k⁴))) = ∛(16·2 × 10⁶/(π·75·0.5904)) = 61.27 mm
di = 0.8·61.27 = 49.02 mm

Answer

do = 61.27 mm

A solid shaft would need d = 51.4 mm; the hollow one is a little larger but much lighter.

4.Torsion of shafts

Answer: d = 55.56 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Torque

ω = 2πN/60 = 2π·750/60 = 78.54 rad/s
T = P/ω = 50000/78.54 = 636.6 N·m

Diameter for strength

T = 636.6 N·m = 636620 N·mm
dτ = ∛(16·636620/(π·40)) = 43.28 mm

Diameter for stiffness

θ = 1·π/180/1000 = 1.745 × 10⁻⁵ rad/mm
G = 39 GPa = 39000 MPa
dφ = (32·636620/(π·39000·1.745 × 10⁻⁵))1/4 = 55.56 mm

Governing diameter

Both limits must hold, so the larger diameter governs.

d = max(43.28, 55.56) = 55.56 mm

Answer

d = 55.56 mm

Here stiffness governs.

5.Mohr’s circle & stress transformation

Answer: τmax = 85.59 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCτmax​

Radius of Mohr’s circle

τmax = R = √(((120 − −50)/2)² + 10²) = 85.59 MPa

Answer

τmax = 85.59 MPa
6.Mohr’s circle & stress transformation

Answer: σn = 41.78 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Thin-walled cylinder: hoop stress σh = pr/t and axial stress σa = pr/(2t); these are the principal stresses in the wall.

Wall stresses

r = 600/2 = 300 mm
σh = pr/t = 2·300/12 = 50 MPa
σa = pr/(2t) = 25 MPa

Transform to the seam

Take x along the axis (σa) and y around the hoop (σh). The seam’s normal makes 90° − α with the axis.

σn = 25·sin²35° + 50·cos²35° = 41.78 MPa

Answer

σn = 41.78 MPa
7.Axial stress & strain

Answer: ε = 10882 µε

Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).

Stress

A = π·10²/4 = 78.54 mm²
σ = P/A = 100·1000/78.54 = 1273 MPa

Strain (Hooke’s law)

E for copper = 117 GPa = 117000 MPa.

ε = σ/E = 1273/117000 = 0.01088 = 10882 µε

Answer

ε = 10882 µε
8.Axial stress & strain

Answer: Pmax = 202.6 kN

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

Ar = π·30²/4 = 706.9 mm²
At = π(80² − 60²)/4 = 2199 mm²

Combined axial stiffness

ΣEA = 200·10³·706.9 + 120·10³·2199 = 4.053 × 10⁸ N

Governing strain

ε = min(0.00075, 0.0005) = 0.0005 (copper)

Largest load

Pmax = 0.0005·4.053 × 10⁸ = 202633 N = 202.6 kN

Answer

Pmax = 202.6 kN
9.Column buckling

Answer: Pcr = 23.55 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·50⁴/64 = 306796 mm⁴

Effective length

KL = 2·1500 = 3000 mm

Critical load

Pcr = π²EI/(KL)² = π²·70000·306796/3000² = 23551 N = 23.55 kN

Answer

Pcr = 23.55 kN
10.Column buckling

Answer: σcr = 21.93 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·40⁴/64 = 125664 mm⁴

Radius of gyration and slenderness

A = 1257 mm²
r = √(I/A) = √(125664/1257) = 10 mm
KL = 2·1500 = 3000 mm
KL/r = 3000/10 = 300

Critical stress

σcr = π²E/(KL/r)² = π²·200000/300² = 21.93 MPa

Answer

σcr = 21.93 MPa
11.Mechanical vibrations

Answer: ζ = 0.08007

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Logarithmic decrement

δ = (1/3)·ln(20/4.4) = 0.5047

Damping ratio

ζ = δ/√(4π² + δ²) = 0.5047/√(39.48 + 0.2547) = 0.08007

Answer

ζ = 0.08007
12.Mechanical vibrations

Answer: fn = 3.001 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.

k12 = 40 + 40 = 80 kN/m
keq = 80·10/(80 + 10) = 8.889 kN/m

Natural frequency

ωn = √(8889/25) = 18.86 rad/s
fn = 18.86/(2π) = 3.001 Hz

Answer

fn = 3.001 Hz

ExamProblems · examproblems.com/courses/machine-design