Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 200 mm pulley at 720 rpm drives a 450 mm pulley by a belt with 3 % slip. Find the speed n2 of the driven pulley.
A 2.2 kW motor at 960 rpm drives gear A (40 teeth), which meshes with gear B (50 teeth). Gear C (16 teeth) on the same shaft as B drives gear D (50 teeth) on the output shaft. Each gear mesh has an efficiency of 97%. Find the output torque Tout.
A solid brass shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.
A solid aluminium shaft of diameter 25 mm is fixed at A. A torque of 250 N·m acts at B, 2.5 m from A, and a torque of 500 N·m in the opposite direction acts at the free end C, a further 1.5 m along. Find the maximum shear stress τmax in the shaft.
A point in a loaded part has σₓ = 40 MPa, σᵧ = −20 MPa and τₓᵧ = 30 MPa (tension positive). Find the maximum in-plane shear stress τmax.
A point in a loaded part has σₓ = 150 MPa, σᵧ = −50 MPa and τₓᵧ = −60 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 20° clockwise from the x-axis.
A bar is made of a steel segment (diameter 30 mm, length 300 mm, E = 200 GPa) joined end to end with a segment made of copper (diameter 40 mm, length 200 mm, E = 120 GPa). It is fixed at one end and pulled at the other. Find the axial load P that stretches it by 0.2 mm in total.
A steel segment (diameter 30 mm, length 500 mm, E = 200 GPa) and a segment made of copper (diameter 60 mm, length 400 mm, E = 120 GPa) are joined end to end and fixed between two rigid walls. An axial load of 80 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.
A column of length L made of aluminium is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of steel is pinned at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
In a free-vibration test of a damped mass–spring system, a displacement peak of 10 mm is followed 4 cycles later by a peak of 1.3 mm. Find the damping ratio ζ.
A 50 kg mass hangs from spring k₃ = 80 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 10 kN/m and k₂ = 30 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: n2 = 310.4 rpm
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: Tout = 80.43 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: φ = 2.394 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: τmax = 163 MPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Sense of TC taken as positive.
The segment with the largest internal torque has the largest stress (same diameter).
Answer: τmax = 42.43 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: σθ = 165.2 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: P = 58 kN
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: σ2 = 21.22 MPa
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: Pcr = 5.118 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: σcr = 31.58 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: ζ = 0.08091
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 3.676 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/machine-design