Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 0.75 kW motor running at 1500 rpm drives a pinion with 15 teeth, which meshes with a gear with 40 teeth. The gear pair has an efficiency of 97%. Find the torque T1 on the motor shaft.
In a compound gear train, gear A (15 teeth) on the input shaft turning at 960 rpm drives gear B (48 teeth). Gear C (18 teeth) is fixed to the same shaft as B and drives gear D (60 teeth) on the output shaft. Find the output speed nout.
In a torsion test, a solid specimen of diameter 10 mm is twisted by a torque of 20 N·m. The two ends of a gauge length of 200 mm rotate 8.98° relative to each other (the material is still elastic). Find the shear modulus G of the material.
A hollow shaft must transmit 100 kW at 1450 rpm. Its inner diameter is to be 0.8 times its outer diameter, and the shear stress must not exceed 75 MPa. Find the smallest outer diameter do.
A point in a loaded part has σₓ = 140 MPa, σᵧ = 120 MPa and τₓᵧ = 50 MPa (tension positive). Find the maximum in-plane shear stress τmax.
A point in a loaded part has σₓ = 120 MPa, σᵧ = 100 MPa and τₓᵧ = 60 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 35° counter-clockwise from the x-axis.
A steel rod (diameter 20 mm, E = 200 GPa) sits inside a tube made of brass (outer diameter 100 mm, inner diameter 50 mm, E = 100 GPa). Both are 800 mm long and are compressed together between rigid plates by 80 kN. Find the shortening δ.
A steel segment (diameter 20 mm, length 300 mm, E = 200 GPa) and a segment made of aluminium (diameter 40 mm, length 500 mm, E = 70 GPa) are joined end to end and fixed between two rigid walls. An axial load of 100 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.
A column of length L made of steel is fixed at the base and pinned at the top. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of aluminium is pinned at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
In a free-vibration test of a damped mass–spring system, a displacement peak of 50 mm is followed 3 cycles later by a peak of 34.3 mm. Find the damping ratio ζ.
A 20 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 12 kN/m and the lower one k₂ = 50 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: T1 = 4.775 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nout = 90 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 10.67 : 1
Answer: G = 26 GPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Compare: steel ≈ 80 GPa, brass ≈ 39 GPa, aluminium ≈ 26 GPa.
Answer: do = 42.31 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
A solid shaft would need d = 35.5 mm; the hollow one is a little larger but much lighter.
Answer: τmax = 50.99 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: σθ = 169.8 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: δ = 0.09818 mm
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: σ2 = 36.33 MPa
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: Pcr = 20.98 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: σcr = 38.86 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: ζ = 0.01999
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 3.501 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/machine-design