Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 150 mm pulley at 1450 rpm drives a 450 mm pulley by a belt with 2.5 % slip. Find the speed n2 of the driven pulley.
In a compound gear train, gear A (48 teeth) on the input shaft turning at 960 rpm drives gear B (80 teeth). Gear C (12 teeth) is fixed to the same shaft as B and drives gear D (16 teeth) on the output shaft. Find the output speed nout.
A solid brass shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.
A solid steel shaft transmits 50 kW at 1000 rpm. The shear stress must not exceed 80 MPa and the twist must not exceed 0.75° per m of length. Find the smallest diameter d that satisfies both limits.
A point in a loaded part has σₓ = 30 MPa, σᵧ = −20 MPa and τₓᵧ = −40 MPa (tension positive). Find the maximum in-plane shear stress τmax.
A solid shaft of diameter 30 mm carries a bending moment of 500 N·m together with a torque of 1500 N·m. At the top surface, where the bending stress is tensile and largest, find the largest principal stress σ1.
A steel rod (diameter 20 mm, E = 200 GPa) sits inside a tube made of aluminium (outer diameter 80 mm, inner diameter 50 mm, E = 70 GPa). Both are 500 mm long and are compressed together between rigid plates by 50 kN. Find the shortening δ.
A steel rod (diameter 40 mm, E = 200 GPa, allowable stress 250 MPa) sits inside a tube made of copper (outer diameter 100 mm, inner diameter 70 mm, E = 120 GPa, allowable stress 60 MPa). They are compressed together between rigid plates. Find the largest load Pmax.
A column of length L made of aluminium is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of steel is fixed at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
A 5 kg mass is supported by a spring with a stiffness of 5 kN/m and a viscous damper with a damping coefficient of 160 N·s/m. Find the damping ratio ζ.
A 20 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 60 kN/m and the lower one k₂ = 15 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: n2 = 471.2 rpm
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: nout = 432 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 2.222 : 1
Answer: φ = 13.86 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: d = 46.42 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Both limits must hold, so the larger diameter governs.
Here stiffness governs.
Answer: τmax = 47.17 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: σ1 = 392.6 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: δ = 0.09017 mm
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: Pmax = 366 kN
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: Pcr = 154.3 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: σcr = 8.567 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: ζ = 0.506
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: fn = 3.898 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/machine-design