Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A belt runs on a 150 mm driving pulley at 1450 rpm. The tension is 1500 N on the tight side and 600 N on the slack side. Find the power P transmitted, in kW.
In a compound gear train, gear A (16 teeth) on the input shaft turning at 960 rpm drives gear B (32 teeth). Gear C (15 teeth) is fixed to the same shaft as B and drives gear D (60 teeth) on the output shaft. Find the output speed nout.
A stepped solid steel shaft is fixed at A. Segment AB has diameter 25 mm and length 1.2 m; segment BC has diameter 20 mm and length 0.5 m. A torque of 500 N·m acts at the free end C. Find the angle of twist φC of end C, in degrees.
A solid aluminium shaft of diameter 40 mm is fixed at A. A torque of 1000 N·m acts at B, 1.5 m from A, and a torque of 200 N·m in the opposite direction acts at the free end C, a further 1.2 m along. Find the maximum shear stress τmax in the shaft.
A point has σₓ = 40 MPa, σᵧ = 60 MPa and τₓᵧ = 20 MPa (tension positive). Find the angle θs, between −90° and 90°, from the x-axis to the normal of the plane on which the shear stress has its maximum positive value +R (shear positive in the same sense as τₓᵧ).
A point in a loaded part has σₓ = 160 MPa, σᵧ = 70 MPa and τₓᵧ = 30 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 50° counter-clockwise from the x-axis.
A steel rod (diameter 25 mm, E = 200 GPa) sits inside a tube made of copper (outer diameter 120 mm, inner diameter 70 mm, E = 120 GPa). Both are 300 mm long and are compressed together between rigid plates by 300 kN. Find the shortening δ.
The stepped bar is fixed at the wall and loaded at its free end. Find the largest normal stress σmax in the bar.
A column of length L made of steel is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of steel is fixed at the base and free at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
A 50 kg mass on a spring with a stiffness of 50 kN/m has a viscous damper giving a damping ratio of 0.35. Find the damped natural frequency fd of its free vibration in Hz.
A 25 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 30 kN/m and k₂ = 80 kN/m. The mass stays level. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: P = 10.25 kW
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: nout = 120 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 8 : 1
Answer: φC = 22.6 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: τmax = 63.66 MPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Sense of TC taken as positive.
The segment with the largest internal torque has the largest stress (same diameter).
Answer: θs = 13.28 °
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
On Mohr’s circle the top point (+R) is 90° from the principal point σ₁; on the element that is 45°.
Positive angles are counter-clockwise.
Answer: σθ = 136.7 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: δ = 0.09059 mm
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: σmax = 1017 MPa
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
The thinner segment has the smaller area, so it carries the larger stress.
Answer: Pcr = 110.2 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: σcr = 27.76 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: fd = 4.715 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 10.56 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/machine-design