Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 0.55 kW motor at 1440 rpm drives a worm with 2 start(s). The worm wheel has 80 teeth and the drive has an efficiency of 70%. Find the output torque Tw on the wheel shaft.
An open belt connects a 100 mm driving pulley at 960 rpm to a 500 mm pulley; the centres are 1200 mm apart. The coefficient of friction is 0.3 and the tight-side tension may not exceed 800 N. Find the largest power P the belt can transmit without slipping, in kW (ignore centrifugal effects).
A solid steel shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.
A hollow shaft transmits 50 kW at 750 rpm. Find the maximum shear stress τmax in the shaft.
A point has σₓ = 90 MPa, σᵧ = 20 MPa and τₓᵧ = 30 MPa (tension positive). The element is rotated 20° clockwise. Find the normal stress σy′ on the faces of the rotated element that are perpendicular to the rotated y′-axis.
A point in a thin plate is in plane stress: σₓ = 90 MPa, σᵧ = −60 MPa and τₓᵧ = 30 MPa (σz = 0). Find the von Mises equivalent stress σvM.
Find the elongation δ of the steel bar under the axial load.
The stepped bar is fixed at the wall and loaded at its free end. Find the largest normal stress σmax in the bar.
A column of length L made of steel is fixed at the base and pinned at the top. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of steel is fixed at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
A 200 kg mass on a spring with a stiffness of 80 kN/m has a viscous damper giving a damping ratio of 0.4. Find the damped natural frequency fd of its free vibration in Hz.
A 10 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 25 kN/m and the lower one k₂ = 40 kN/m. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: Tw = 102.1 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: P = 2.289 kW
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: φ = 5.699 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: τmax = 5.492 MPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: σy′ = 47.47 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
The sum of the normal stresses does not change with rotation.
Answer: σvM = 140.7 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.
Answer: δ = 1.986 mm
Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).
E for steel = 200 GPa = 200000 MPa.
Answer: σmax = 382 MPa
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
The thinner segment has the smaller area, so it carries the larger stress.
Answer: Pcr = 900 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: σcr = 17.77 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: fd = 2.917 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 15.38 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/machine-design