Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 3 kW motor running at 960 rpm drives a pinion with 20 teeth, which meshes with a gear with 24 teeth. The gear pair has an efficiency of 97%. Find the output torque T2 on the gear shaft.
In a compound gear train, gear A (15 teeth) on the input shaft turning at 2900 rpm drives gear B (20 teeth). Gear C (30 teeth) is fixed to the same shaft as B and drives gear D (80 teeth) on the output shaft. Find the output speed nout.
A solid aluminium shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.
A solid shaft must transmit 10 kW at 500 rpm without the shear stress exceeding 80 MPa. Find the smallest diameter d that works.
A point in a thin plate is in plane stress: σₓ = 120 MPa, σᵧ = 20 MPa and τₓᵧ = −20 MPa, with σz = 0. Find the absolute maximum shear stress τabs at the point (considering all planes in three dimensions).
A point in a thin plate is in plane stress: σₓ = 70 MPa, σᵧ = −20 MPa and τₓᵧ = 40 MPa (σz = 0). The material has a yield strength of 275 MPa. Find the factor of safety n against yielding by the Tresca (maximum shear stress) criterion.
Find the elongation δ of the copper bar under the axial load.
A steel rod (diameter 20 mm, E = 200 GPa, allowable stress 200 MPa) sits inside a tube made of copper (outer diameter 100 mm, inner diameter 50 mm, E = 120 GPa, allowable stress 100 MPa). They are compressed together between rigid plates. Find the largest load Pmax.
A column of length L made of aluminium is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A solid round column of length L made of steel is pinned at both ends. It must carry 105 kN with a factor of safety of 3 against buckling. Find the smallest diameter d.
A 150 kg mass on a spring with a stiffness of 80 kN/m has a viscous damper giving a damping ratio of 0.35. Find the damped natural frequency fd of its free vibration in Hz.
A 10 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 100 kN/m and k₂ = 40 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: T2 = 34.74 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nout = 815.6 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 3.556 : 1
Answer: φ = 13.86 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: d = 22.99 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
In practice you would round up to the next standard size.
Answer: τabs = 61.93 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. In three dimensions the absolute maximum shear stress is (σmax − σmin)/2 over all three principal stresses; in plane stress the third one is zero.
Here the out-of-plane circle governs: the absolute maximum is larger than the in-plane maximum R.
Answer: n = 2.284
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.
n > 1 means the point does not yield; Tresca is slightly more conservative than von Mises.
Answer: δ = 11.43 mm
Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).
E for copper = 117 GPa = 117000 MPa.
Answer: Pmax = 641.4 kN
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: Pcr = 5.426 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: d = 60.05 mm
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Check: the slenderness KL/r is 133.2, so the column is slender and Euler applies.
Answer: fd = 3.443 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 140 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/machine-design