Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 3 kW motor running at 1450 rpm drives a pinion with 30 teeth and a module of 5 mm. Find the tangential force Ft on the pinion teeth.
An open belt connects a 125 mm pulley and a 315 mm pulley whose centres are 600 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.
In a torsion test, a solid specimen of diameter 12 mm is twisted by a torque of 20 N·m. The two ends of a gauge length of 300 mm rotate 2.11° relative to each other (the material is still elastic). Find the shear modulus G of the material.
A solid brass shaft of diameter 40 mm is fixed at A. A torque of 750 N·m acts at B, 3 m from A, and a torque of 100 N·m in the opposite direction acts at the free end C, a further 0.5 m along. Find the maximum shear stress τmax in the shaft.
A point in a loaded part has σₓ = 160 MPa, σᵧ = 20 MPa and τₓᵧ = −10 MPa (tension positive). Find the angle θp from the x-axis to the direction of the largest principal stress, between −90° and 90°.
A point in a loaded part has σₓ = 0 MPa, σᵧ = −10 MPa and τₓᵧ = 30 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 20° counter-clockwise from the x-axis.
A steel rod (diameter 20 mm, E = 200 GPa) sits inside a tube made of copper (outer diameter 120 mm, inner diameter 70 mm, E = 120 GPa). Both are 300 mm long and are compressed together between rigid plates by 150 kN. Find the shortening δ.
A steel segment (diameter 25 mm, length 600 mm, E = 200 GPa) and a segment made of copper (diameter 40 mm, length 300 mm, E = 120 GPa) are joined end to end and fixed between two rigid walls. An axial load of 60 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.
A column of length L made of aluminium is fixed at the base and pinned at the top. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of aluminium is fixed at the base and pinned at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
An 80 kg mass is supported by a spring with a stiffness of 12 kN/m and a viscous damper with a damping coefficient of 100 N·s/m. Find the damping ratio ζ.
A 50 kg mass hangs from spring k₃ = 50 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 30 kN/m and k₂ = 100 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: Ft = 263.4 N
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: θ = 161.8 °
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: G = 80.03 GPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Compare: steel ≈ 80 GPa, brass ≈ 39 GPa, aluminium ≈ 26 GPa.
Answer: τmax = 51.73 MPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Sense of TC taken as positive.
The segment with the largest internal torque has the largest stress (same diameter).
Answer: θp = −4.065 °
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Point x sits at an angle 2θp from the σ-axis on Mohr’s circle; the quadrant follows from the signs of σₓ − σᵧ and τₓᵧ.
Positive angles are counter-clockwise.
Answer: σθ = 18.11 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: δ = 0.04696 mm
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: σ2 = 36.02 MPa
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: Pcr = 9.914 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: σcr = 12.69 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: ζ = 0.05103
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: fn = 4.277 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/machine-design