Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 150 mmd2​ = 300 mm1500 rpmn2​ = ?

A 150 mm pulley at 1500 rpm drives a 300 mm pulley by a belt with 1 % slip. Find the speed n2 of the driven pulley.

n1 = 1500 rpmd1 = 150 mmd2 = 300 mms = 1 %
n2 = rpm
2.Gears & gear trainsHard
Ns​ = 16nr​ = ?Np​ = 24carrier fixed

In a planetary gear set the sun gear has 16 teeth and each planet gear has 24 teeth. The planet carrier is held fixed and the sun is driven at 1200 rpm. Find the speed nr of the ring gear (magnitude).

Ns = 16Np = 24ns = 1200 rpm
nr = rpm
3.Torsion of shaftsMedium
T = 100 N·md = 20 mmL = 1.5 mφ = ?

A solid steel shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.

T = 100 N·md = 20 mmL = 1.5 mG = 80 GPa
φ = °
4.Torsion of shaftsHard
d = 25 mmT0​ = 1000 N·mACBa = 2 mb = 0.8 m

A solid steel shaft of diameter 25 mm is fixed to rigid walls at both ends A and B. A torque of 1000 N·m is applied at C, 2 m from A and 0.8 m from B. Find the reaction torque TA at wall A.

d = 25 mmT0 = 1000 N·ma = 2 mb = 0.8 m
TA = N·m
5.Mohr’s circle & stress transformationMedium
σx​ = 30σy​ = 10τxy​ = −20MPa

A point in a loaded part has σₓ = 30 MPa, σᵧ = 10 MPa and τₓᵧ = −20 MPa (tension positive). Find the angle θp from the x-axis to the direction of the largest principal stress, between −90° and 90°.

σx = 30 MPaσy = 10 MPaτxy = −20 MPa
θp = °
6.Mohr’s circle & stress transformationHard
σx​ = −70σy​ = 10τxy​ = 40MPa

A point in a loaded part has σₓ = −70 MPa, σᵧ = 10 MPa and τₓᵧ = 40 MPa (tension positive). Find the shear stress τθ on a plane whose normal is rotated 45° clockwise from the x-axis (positive in the same sense as τₓᵧ).

σx = −70 MPaσy = 10 MPaτxy = 40 MPaθ = -45°
τθ = MPa
7.Axial stress & strainMedium
P = ?12600 mm200 mmØ20Ø50δ = 0.25 mm

A bar is made of a steel segment (diameter 20 mm, length 600 mm, E = 200 GPa) joined end to end with a segment made of brass (diameter 50 mm, length 200 mm, E = 100 GPa). It is fixed at one end and pulled at the other. Find the axial load P that stretches it by 0.25 mm in total.

segment 1: steel, Ø20 mm, 600 mm, E = 200 GPasegment 2: brass, Ø50 mm, 200 mm, E = 100 GPaδ = 0.25 mm
P = kN
8.Axial stress & strainHard
Ø 30 mmBrass2 mØ 16 mmAluminium0.5 mP = 115 kN

The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.

P = 115 kNsegment 1: Ø30 mm, 2 m, brass (E = 100 GPa)segment 2: Ø16 mm, 0.5 m, aluminium (E = 70 GPa)
δ = mm
9.Column bucklingMedium
PL = 6 md = 80 mmcross-section

A column of length L made of steel is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 6 mE = 200 GPa (steel)d = 80 mm
Pcr = kN
10.Column bucklingHard
PL = 1 md = 20 mmcross-section

A column of length L made of steel is fixed at the base and pinned at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 1 mE = 200 GPa (steel)d = 20 mm
σcr = MPa
11.Mechanical vibrationsMedium
k = 150 kN/mζ = 0.5m = 250 kg

A 250 kg mass on a spring with a stiffness of 150 kN/m has a viscous damper giving a damping ratio of 0.5. Find the damped natural frequency fd of its free vibration in Hz.

m = 250 kgk = 150 kN/mζ = 0.5
fd = Hz
12.Mechanical vibrationsHard
k1​ = 20k2​ = 12m = 20 kg

A 20 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 20 kN/m and the lower one k₂ = 12 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.

m = 20 kgk1 = 20 kN/mk2 = 12 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: n2 = 742.5 rpm

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Speed without slip

1500·150/300 = 750 rpm

With slip

n2 = 750·0.99 = 742.5 rpm

Answer

n2 = 742.5 rpm
2.Gears & gear trains

Answer: nr = 300 rpm

Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.

Ring gear teeth

Nr = Ns + 2·Np = 16 + 2·24 = 64

Willis equation with the carrier fixed

With nc = 0 the sun drives the ring through the planets, which act as idlers.

nr = −ns·Ns/Nr = −1200·16/64 = −300 rpm
|nr| = 300 rpm

Answer

nr = 300 rpm

The ring turns opposite to the sun.

3.Torsion of shafts

Answer: φ = 6.839 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Polar second moment of area

J = π·20⁴/32 = 15708 mm⁴

Angle of twist

φ = TL/(GJ) = 100·1000·1500/(80000·15708) = 0.1194 rad
φ = 0.1194·180/π = 6.839°

Answer

φ = 6.839°
4.Torsion of shafts

Answer: TA = 285.7 N·m

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω. When both ends are fixed, statics alone gives only TA + TB = T₀; the second equation is compatibility (equal twist of both parts at the loaded section).

Equilibrium and compatibility

TA + TB = 1000
TA·a = TB·b
TA = 1000·0.8/2.8 = 285.7 N·m
TB = 1000·2/2.8 = 714.3 N·m

Answer

TA = 285.7 N·m
5.Mohr’s circle & stress transformation

Answer: θp = −31.72 °

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCσ1​σ2​

Angle on the circle

Point x sits at an angle 2θp from the σ-axis on Mohr’s circle; the quadrant follows from the signs of σₓ − σᵧ and τₓᵧ.

2θp = atan2(2·−20, 30 − 10) = −63.43°

Angle on the element

θp = −31.72°

Answer

θp = −31.72°

Positive angles are counter-clockwise.

6.Mohr’s circle & stress transformation

Answer: τθ = −40 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Transformation equation

τθ = −−40·−1 + 40·0 = −40 MPa

Answer

τθ = −40 MPa
7.Axial stress & strain

Answer: P = 23.66 kN

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

A₁ = 314.2 mm², A₂ = 1963 mm²

Flexibilities

L₁/(E₁A₁) = 600/(200000·314.2) = 9.549 × 10⁻⁶ mm/N
L₂/(E₂A₂) = 200/(100000·1963) = 1.019 × 10⁻⁶ mm/N

Load

P = 0.25/1.057 × 10⁻⁵ = 23657 N = 23.66 kN

Answer

P = 23.66 kN
8.Axial stress & strain

Answer: δ = 7.339 mm

Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.

Same force in both segments

The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.

A1 = π·30²/4 = 706.9 mm², A2 = π·16²/4 = 201.1 mm²
σ1 = 162.7 MPa
σ2 = 572 MPa

Add the segment elongations

δ1 = σ1L1/E1 = 162.7·2000/100000 = 3.254 mm
δ2 = σ2L2/E2 = 572·500/70000 = 4.085 mm
δ = δ1 + δ2 = 7.339 mm

Answer

δ = 7.339 mm
9.Column buckling

Answer: Pcr = 110.2 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·80⁴/64 = 2.011 × 10⁶ mm⁴

Effective length

KL = 1·6000 = 6000 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·2.011 × 10⁶/6000² = 110245 N = 110.2 kN

Answer

Pcr = 110.2 kN
10.Column buckling

Answer: σcr = 100.7 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·20⁴/64 = 7854 mm⁴

Radius of gyration and slenderness

A = 314.2 mm²
r = √(I/A) = √(7854/314.2) = 5 mm
KL = 0.7·1000 = 700 mm
KL/r = 700/5 = 140

Critical stress

σcr = π²E/(KL/r)² = π²·200000/140² = 100.7 MPa

Answer

σcr = 100.7 MPa
11.Mechanical vibrations

Answer: fd = 3.376 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Undamped natural frequency

ωn = √(150000/250) = 24.49 rad/s
fn = 24.49/(2π) = 3.898 Hz

Damped natural frequency

fd = fn·√(1 − ζ²) = 3.898·√(1 − 0.5²) = 3.376 Hz

Answer

fd = 3.376 Hz
12.Mechanical vibrations

Answer: fn = 3.082 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.

1/keq = 1/20 + 1/12 → keq = 20·12/(20 + 12) = 7.5 kN/m

Natural frequency

ωn = √(7500/20) = 19.36 rad/s
fn = 19.36/(2π) = 3.082 Hz

Answer

fn = 3.082 Hz

ExamProblems · examproblems.com/courses/machine-design