Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
N1​ = 25, m = 2.5 mm

A 7.5 kW motor running at 960 rpm drives a pinion with 25 teeth and a module of 2.5 mm. Find the tangential force Ft on the pinion teeth.

P = 7.5 kWn = 960 rpmN1 = 25m = 2.5 mm
Ft = N
2.Gears & gear trainsHard
Ns​ = 24nr​ = ?Np​ = 24carrier fixed

In a planetary gear set the sun gear has 24 teeth and each planet gear has 24 teeth. The planet carrier is held fixed and the sun is driven at 1500 rpm. Find the speed nr of the ring gear (magnitude).

Ns = 24Np = 24ns = 1500 rpm
nr = rpm
3.Torsion of shaftsMedium
do​ = ?T = 750 N·m

A hollow shaft must carry a torque of 750 N·m. Its inner diameter is to be 0.6 times its outer diameter, and the shear stress must not exceed 60 MPa. Find the smallest outer diameter do.

T = 750 N·mdi/do = 0.6τallow = 60 MPa
do = mm
4.Torsion of shaftsHard
d = 25 mmTB​ = 400 N·mTC​ = 100 N·mABC1.5 m1.5 m

A solid aluminium shaft of diameter 25 mm is fixed at A. A torque of 400 N·m acts at B, 1.5 m from A, and a torque of 100 N·m in the opposite direction acts at the free end C, a further 1.5 m along. Find the magnitude of the angle of twist φC of end C, in degrees.

d = 25 mmTB = 400 N·mTC = 100 N·mAB = 1.5 mBC = 1.5 mG = 26 GPa
φC = °
5.Mohr’s circle & stress transformationMedium
σx​ = −50σy​ = 110τxy​ = 20MPa

A point in a loaded part has σₓ = −50 MPa, σᵧ = 110 MPa and τₓᵧ = 20 MPa (tension positive). Find the maximum in-plane shear stress τmax.

σx = −50 MPaσy = 110 MPaτxy = 20 MPa
τmax = MPa
6.Mohr’s circle & stress transformationHard
σx​ = 160σy​ = 90τxy​ = −50MPa

A point in a thin plate is in plane stress: σₓ = 160 MPa, σᵧ = 90 MPa and τₓᵧ = −50 MPa (σz = 0). The material has a yield strength of 350 MPa. Find the factor of safety n against yielding by the Tresca (maximum shear stress) criterion.

σx = 160 MPaσy = 90 MPaτxy = −50 MPaσY = 350 MPa
n =
7.Axial stress & strainMedium
Ø 25 mmAluminium3 mP = 75 kN

Find the elongation δ of the aluminium bar under the axial load.

P = 75 kNd = 25 mmL = 3 mE = 70 GPa
δ = mm
8.Axial stress & strainHard
60 kN12400 mm500 mmØ25Ø50σ2​ = ?

A steel segment (diameter 25 mm, length 400 mm, E = 200 GPa) and a segment made of copper (diameter 50 mm, length 500 mm, E = 120 GPa) are joined end to end and fixed between two rigid walls. An axial load of 60 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.

segment 1: steel, Ø25 mm, 400 mm, E = 200 GPasegment 2: copper, Ø50 mm, 500 mm, E = 120 GPaP = 60 kN
σ2 = MPa
9.Column bucklingMedium
PL = 2 md = 20 mmcross-section

A column of length L made of steel is fixed at the base and pinned at the top. Using Euler’s formula, find its critical buckling load Pcr.

L = 2 mE = 200 GPa (steel)d = 20 mm
Pcr = kN
10.Column bucklingHard
PL = 2 md = 20 mmcross-section

A column of length L made of steel is pinned at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 2 mE = 200 GPa (steel)d = 20 mm
σcr = MPa
11.Mechanical vibrationsMedium
tx10 mm5 cycles0.8 mm

In a free-vibration test of a damped mass–spring system, a displacement peak of 10 mm is followed 5 cycles later by a peak of 0.8 mm. Find the damping ratio ζ.

x0 = 10 mmx5 = 0.8 mmn = 5
ζ =
12.Mechanical vibrationsHard
k1​ = 40k2​ = 10k3​ = 80m = 20 kg

A 20 kg mass hangs from spring k₃ = 80 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 40 kN/m and k₂ = 10 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.

m = 20 kgk1 = 40 kN/mk2 = 10 kN/mk3 = 80 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: Ft = 2387 N

Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.

Torque on the pinion

ω = 2π·960/60 = 100.5 rad/s
T = P/ω = 7500/100.5 = 74.6 N·m

Pitch diameter

d = m·N = 2.5·25 = 62.5 mm

Tangential force

Ft = 2T/d = 2·74.6/0.0625 = 2387 N

Answer

Ft = 2387 N
2.Gears & gear trains

Answer: nr = 500 rpm

Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.

Ring gear teeth

Nr = Ns + 2·Np = 24 + 2·24 = 72

Willis equation with the carrier fixed

With nc = 0 the sun drives the ring through the planets, which act as idlers.

nr = −ns·Ns/Nr = −1500·24/72 = −500 rpm
|nr| = 500 rpm

Answer

nr = 500 rpm

The ring turns opposite to the sun.

3.Torsion of shafts

Answer: do = 41.82 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Outer diameter from the allowable stress

T = 750 N·m = 750000 N·mm
1 − k⁴ = 1 − 0.6⁴ = 0.8704
do = ∛(16T/(π·τallow·(1 − k⁴))) = ∛(16·750000/(π·60·0.8704)) = 41.82 mm
di = 0.6·41.82 = 25.09 mm

Answer

do = 41.82 mm

A solid shaft would need d = 39.93 mm; the hollow one is a little larger but much lighter.

4.Torsion of shafts

Answer: φC = 17.24 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Internal torques

Sense of TC taken as positive.

TBC = TC = 100 N·m
TAB = TC − TB = 100 − 400 = −300 N·m

Twist of each segment

J = π·25⁴/32 = 38350 mm⁴
G = 26 GPa = 26000 MPa
φAB = −300000·1500/(26000·38350) = −0.4513 rad
φBC = 100000·1500/(26000·38350) = 0.1504 rad

Twist of end C

φC = −0.4513 + 0.1504 = −0.3009 rad → |φC| = 17.24°

Answer

φC = 17.24°
5.Mohr’s circle & stress transformation

Answer: τmax = 82.46 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCτmax​

Radius of Mohr’s circle

τmax = R = √(((−50 − 110)/2)² + 20²) = 82.46 MPa

Answer

τmax = 82.46 MPa
6.Mohr’s circle & stress transformation

Answer: n = 1.881

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.

στxyCσ1​σ2​

Principal stresses

C = 125 MPa, R = 61.03 MPa
σ1 = 186 MPa, σ2 = 63.97 MPa, σ3 = 0

Tresca

σmax − σmin = 186 MPa
n = 350/186 = 1.881

Answer

n = 1.881

n > 1 means the point does not yield; Tresca is slightly more conservative than von Mises.

7.Axial stress & strain

Answer: δ = 6.548 mm

Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).

Stress

A = π·25²/4 = 490.9 mm²
σ = P/A = 75·1000/490.9 = 152.8 MPa

Strain (Hooke’s law)

E for aluminium = 70 GPa = 70000 MPa.

ε = σ/E = 152.8/70000 = 0.002183 = 2183 µε

Elongation

δ = ε·L = 0.002183·3000 mm = 6.548 mm

Answer

δ = 6.548 mm
8.Axial stress & strain

Answer: σ2 = 20.09 MPa

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Stiffnesses

k₁ = 200000·490.9/400 = 245437 N/mm
k₂ = 120000·1963/500 = 471239 N/mm

Share of segment 2

F2 = 60000·471239/716676 = 39452 N

Stress

σ2 = 39452/1963 = 20.09 MPa (compression)

Answer

σ2 = 20.09 MPa
9.Column buckling

Answer: Pcr = 7.91 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·20⁴/64 = 7854 mm⁴

Effective length

KL = 0.7·2000 = 1400 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·7854/1400² = 7910 N = 7.91 kN

Answer

Pcr = 7.91 kN
10.Column buckling

Answer: σcr = 12.34 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·20⁴/64 = 7854 mm⁴

Radius of gyration and slenderness

A = 314.2 mm²
r = √(I/A) = √(7854/314.2) = 5 mm
KL = 1·2000 = 2000 mm
KL/r = 2000/5 = 400

Critical stress

σcr = π²E/(KL/r)² = π²·200000/400² = 12.34 MPa

Answer

σcr = 12.34 MPa
11.Mechanical vibrations

Answer: ζ = 0.08014

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Logarithmic decrement

δ = (1/5)·ln(10/0.8) = 0.5051

Damping ratio

ζ = δ/√(4π² + δ²) = 0.5051/√(39.48 + 0.2552) = 0.08014

Answer

ζ = 0.08014
12.Mechanical vibrations

Answer: fn = 6.243 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.

k12 = 40 + 10 = 50 kN/m
keq = 50·80/(50 + 80) = 30.77 kN/m

Natural frequency

ωn = √(30769/20) = 39.22 rad/s
fn = 39.22/(2π) = 6.243 Hz

Answer

fn = 6.243 Hz

ExamProblems · examproblems.com/courses/machine-design