Machine Design: cram pack

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = e^μθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τ_max = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(d_o⁴ − d_i⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τ_max = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(d_o⁴ − d_i⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω. When both ends are fixed, statics alone gives only T_A + T_B = T₀; the second equation is compatibility (equal twist of both parts at the loaded section).

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).

Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.

Euler buckling: a slender column becomes unstable at P_cr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Euler buckling: a slender column becomes unstable at P_cr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Free vibration of a mass–spring system: the undamped natural frequency is ω_n = √(k/m) in rad/s, and f_n = ω_n/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/c_c, with critical damping c_c = 2·√(k·m) = 2·m·ω_n. An underdamped system (ζ < 1) oscillates at ω_d = ω_n·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Free vibration of a mass–spring system: the undamped natural frequency is ω_n = √(k/m) in rad/s, and f_n = ω_n/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/c_c, with critical damping c_c = 2·√(k·m) = 2·m·ω_n. An underdamped system (ζ < 1) oscillates at ω_d = ω_n·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.