Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 3 kW motor running at 1450 rpm drives a pinion with 24 teeth and a module of 4 mm. Find the tangential force Ft on the pinion teeth.
In a planetary gear set the sun gear has 30 teeth and each planet gear has 20 teeth. The ring gear is held fixed and the sun is driven at 1440 rpm. Find the speed nc of the planet carrier.
A solid steel shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.
A solid shaft must transmit 50 kW at 3000 rpm without the shear stress exceeding 40 MPa. Find the smallest diameter d that works.
A point in a loaded part has σₓ = 120 MPa, σᵧ = 70 MPa and τₓᵧ = −20 MPa (tension positive). Find the angle θp from the x-axis to the direction of the largest principal stress, between −90° and 90°.
A point in a thin plate is in plane stress: σₓ = −50 MPa, σᵧ = 120 MPa and τₓᵧ = 10 MPa (σz = 0). The material has a yield strength of 250 MPa. Find the factor of safety n against yielding by the von Mises (distortion energy) criterion.
Find the elongation δ of the steel bar under the axial load.
The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.
A column of length L made of aluminium is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of steel is pinned at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
In a free-vibration test of a damped mass–spring system, a displacement peak of 10 mm is followed 5 cycles later by a peak of 0.8 mm. Find the damping ratio ζ.
A 25 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 25 kN/m and k₂ = 60 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: Ft = 411.6 N
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: nc = 432 rpm
Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.
Set nr = 0 and solve for the carrier speed.
The carrier turns in the same direction as the sun.
Answer: φ = 14.94 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: d = 27.26 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
In practice you would round up to the next standard size.
Answer: θp = −19.33 °
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Point x sits at an angle 2θp from the σ-axis on Mohr’s circle; the quadrant follows from the signs of σₓ − σᵧ and τₓᵧ.
Positive angles are counter-clockwise.
Answer: n = 1.641
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.
n > 1 means the point does not yield; Tresca is slightly more conservative than von Mises.
Answer: δ = 0.6631 mm
Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).
E for steel = 200 GPa = 200000 MPa.
Answer: δ = 8.056 mm
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
Answer: Pcr = 47.98 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: σcr = 49.35 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: ζ = 0.08014
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 85 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/machine-design