Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 200 mmd2​ = 250 mm720 rpmT1​ = 1200 NT2​ = 240 NP = ?

A belt runs on a 200 mm driving pulley at 720 rpm. The tension is 1200 N on the tight side and 240 N on the slack side. Find the power P transmitted, in kW.

d1 = 200 mmn1 = 720 rpmT1 = 1200 NT2 = 240 N
P = kW
2.Gears & gear trainsHard
d1​ = 160 mmd2​ = 250 mm720 rpmC = 600 mmT1​ = 600 NT2​P = ?

An open belt connects a 160 mm driving pulley at 720 rpm to a 250 mm pulley; the centres are 600 mm apart. The coefficient of friction is 0.25 and the tight-side tension may not exceed 600 N. Find the largest power P the belt can transmit without slipping, in kW (ignore centrifugal effects).

d1 = 160 mmn1 = 720 rpmd2 = 250 mmC = 600 mmμ = 0.25T1 = 600 N
P = kW
3.Torsion of shaftsMedium
do​ = 40, di​ = 20 mmT = 100 N·mL = 1.2 m

A hollow brass shaft (outer diameter 40 mm, inner diameter 20 mm, length 1.2 m) is fixed at one end and twisted by a torque of 100 N·m at the other. Find the angle of twist φ in degrees.

T = 100 N·mdo = 40 mmdi = 20 mmL = 1.2 mG = 39 GPa
φ = °
4.Torsion of shaftsHard
Td = ?

A solid shaft must transmit 5 kW at 3000 rpm without the shear stress exceeding 60 MPa. Find the smallest diameter d that works.

P = 5 kWN = 3000 rpmτallow = 60 MPa
d = mm
5.Mohr’s circle & stress transformationMedium
σx​ = 80σy​ = 10τxy​ = −10MPa

A point in a loaded part has σₓ = 80 MPa, σᵧ = 10 MPa and τₓᵧ = −10 MPa (tension positive). Find the maximum in-plane shear stress τmax.

σx = 80 MPaσy = 10 MPaτxy = −10 MPa
τmax = MPa
6.Mohr’s circle & stress transformationHard
σx​ = 70σy​ = 70τxy​ = 60MPa

A point in a loaded part has σₓ = 70 MPa, σᵧ = 70 MPa and τₓᵧ = 60 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 15° counter-clockwise from the x-axis.

σx = 70 MPaσy = 70 MPaτxy = 60 MPaθ = 15°
σθ = MPa
7.Axial stress & strainMedium
250 kNØ4070 GPaØ120/60500 mmδ = ?

A steel rod (diameter 40 mm, E = 200 GPa) sits inside a tube made of aluminium (outer diameter 120 mm, inner diameter 60 mm, E = 70 GPa). Both are 500 mm long and are compressed together between rigid plates by 250 kN. Find the shortening δ.

P = 250 kNrod: Ø40 mm, E = 200 GPatube: Ø120/Ø60 mm, E = 70 GPaL = 500 mm
δ = mm
8.Axial stress & strainHard
80 kN12500 mm500 mmØ40Ø50σ2​ = ?

A steel segment (diameter 40 mm, length 500 mm, E = 200 GPa) and a segment made of copper (diameter 50 mm, length 500 mm, E = 120 GPa) are joined end to end and fixed between two rigid walls. An axial load of 80 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.

segment 1: steel, Ø40 mm, 500 mm, E = 200 GPasegment 2: copper, Ø50 mm, 500 mm, E = 120 GPaP = 80 kN
σ2 = MPa
9.Column bucklingMedium
PL = 2.5 md = 60 mmcross-section

A column of length L made of aluminium is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.

L = 2.5 mE = 70 GPa (aluminium)d = 60 mm
Pcr = kN
10.Column bucklingHard
PL = 2.5 md = 40 mmcross-section

A column of length L made of steel is fixed at the base and pinned at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 2.5 mE = 200 GPa (steel)d = 40 mm
σcr = MPa
11.Mechanical vibrationsMedium
k = 200 kN/mc = 140 N·s/mm = 10 kg

A 10 kg mass is supported by a spring with a stiffness of 200 kN/m and a viscous damper with a damping coefficient of 140 N·s/m. Find the damping ratio ζ.

m = 10 kgk = 200 kN/mc = 140 N·s/m
ζ =
12.Mechanical vibrationsHard
k1​ = 30k2​ = 30k3​ = 50m = 25 kg

A 25 kg mass hangs from spring k₃ = 50 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 30 kN/m and k₂ = 30 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.

m = 25 kgk1 = 30 kN/mk2 = 30 kN/mk3 = 50 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: P = 7.238 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt speed

v = 7.54 m/s

Power

P = (1200 − 240)·7.54 = 7238 W = 7.238 kW

Answer

P = 7.238 kW
2.Gears & gear trains

Answer: P = 1.906 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Angle of wrap

θ = 2.991 rad

Slack-side tension

eμθ = e0.7479 = 2.112, T₂ = 600/2.112 = 284 N

Power

P = (600 − 284)·6.032 = 1.906 kW

Answer

P = 1.906 kW
3.Torsion of shafts

Answer: φ = 0.7482 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Polar second moment of area

J = π(40⁴ − 20⁴)/32 = 235619 mm⁴

Angle of twist

T = 100 N·m = 100000 N·mm
L = 1.2 m = 1200 mm
G = 39 GPa = 39000 MPa
φ = TL/(GJ) = 100000·1200/(39000·235619) = 0.01306 rad
φ = 0.01306·180/π = 0.7482°

Answer

φ = 0.7482°
4.Torsion of shafts

Answer: d = 11.05 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Torque

ω = 2πN/60 = 2π·3000/60 = 314.2 rad/s
T = P/ω = 5000/314.2 = 15.92 N·m

Diameter from the allowable stress

d = ∛(16T/(π·τallow)) = ∛(16·15915/(π·60)) = 11.05 mm

Answer

d = 11.05 mm

In practice you would round up to the next standard size.

5.Mohr’s circle & stress transformation

Answer: τmax = 36.4 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCτmax​

Radius of Mohr’s circle

τmax = R = √(((80 − 10)/2)² + −10²) = 36.4 MPa

Answer

τmax = 36.4 MPa
6.Mohr’s circle & stress transformation

Answer: σθ = 100 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Transformation equation

σθ = 70 + 0·0.866 + 60·0.5 = 100 MPa

Answer

σθ = 100 MPa
7.Axial stress & strain

Answer: δ = 0.1479 mm

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

Ar = π·40²/4 = 1257 mm²
At = π(120² − 60²)/4 = 8482 mm²

Combined axial stiffness

ΣEA = 200·10³·1257 + 70·10³·8482 = 8.451 × 10⁸ N

Shortening

δ = 250000·500/8.451 × 10⁸ = 0.1479 mm

Answer

δ = 0.1479 mm
8.Axial stress & strain

Answer: σ2 = 19.71 MPa

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Stiffnesses

k₁ = 200000·1257/500 = 502655 N/mm
k₂ = 120000·1963/500 = 471239 N/mm

Share of segment 2

F2 = 80000·471239/973894 = 38710 N

Stress

σ2 = 38710/1963 = 19.71 MPa (compression)

Answer

σ2 = 19.71 MPa
9.Column buckling

Answer: Pcr = 17.58 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·60⁴/64 = 636173 mm⁴

Effective length

KL = 2·2500 = 5000 mm

Critical load

Pcr = π²EI/(KL)² = π²·70000·636173/5000² = 17581 N = 17.58 kN

Answer

Pcr = 17.58 kN
10.Column buckling

Answer: σcr = 64.45 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·40⁴/64 = 125664 mm⁴

Radius of gyration and slenderness

A = 1257 mm²
r = √(I/A) = √(125664/1257) = 10 mm
KL = 0.7·2500 = 1750 mm
KL/r = 1750/10 = 175

Critical stress

σcr = π²E/(KL/r)² = π²·200000/175² = 64.45 MPa

Answer

σcr = 64.45 MPa
11.Mechanical vibrations

Answer: ζ = 0.0495

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Critical damping

cc = 2·√(k·m) = 2·√(200000·10) = 2828 N·s/m

Damping ratio

ζ = c/cc = 140/2828 = 0.0495

Answer

ζ = 0.0495

ζ < 1, so the system is underdamped and oscillates as it decays.

12.Mechanical vibrations

Answer: fn = 5.257 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.

k12 = 30 + 30 = 60 kN/m
keq = 60·50/(60 + 50) = 27.27 kN/m

Natural frequency

ωn = √(27273/25) = 33.03 rad/s
fn = 33.03/(2π) = 5.257 Hz

Answer

fn = 5.257 Hz

ExamProblems · examproblems.com/courses/machine-design