Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 1.5 kW motor running at 1450 rpm drives a pinion with 18 teeth, which meshes with a gear with 50 teeth. The gear pair has an efficiency of 98%. Find the output torque T2 on the gear shaft.
In a planetary gear set the sun gear has 12 teeth and each planet gear has 15 teeth. The planet carrier is held fixed and the sun is driven at 900 rpm. Find the speed nr of the ring gear (magnitude).
A solid aluminium shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.
A solid aluminium shaft transmits 10 kW at 500 rpm. The shear stress must not exceed 50 MPa and the twist must not exceed 0.25° per m of length. Find the smallest diameter d that satisfies both limits.
A point has σₓ = 160 MPa, σᵧ = −70 MPa and τₓᵧ = −50 MPa (tension positive). Find the angle θs, between −90° and 90°, from the x-axis to the normal of the plane on which the shear stress has its maximum positive value +R (shear positive in the same sense as τₓᵧ).
A point in a thin plate is in plane stress: σₓ = −20 MPa, σᵧ = −80 MPa and τₓᵧ = 60 MPa (σz = 0). The material has a yield strength of 350 MPa. Find the factor of safety n against yielding by the von Mises (distortion energy) criterion.
A steel rod (diameter 40 mm, E = 200 GPa) sits inside a tube made of copper (outer diameter 80 mm, inner diameter 50 mm, E = 120 GPa). Both are 500 mm long and are compressed together between rigid plates by 100 kN. Find the shortening δ.
A steel segment (diameter 40 mm, length 400 mm, E = 200 GPa) and a segment made of brass (diameter 50 mm, length 400 mm, E = 100 GPa) are joined end to end and fixed between two rigid walls. An axial load of 100 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.
A column of length L made of steel is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A solid round column of length L made of aluminium is fixed at the base and free at the top. It must carry 65 kN with a factor of safety of 2 against buckling. Find the smallest diameter d.
A 12 kg mass is supported by a spring with a stiffness of 5 kN/m and a viscous damper with a damping coefficient of 70 N·s/m. Find the damping ratio ζ.
A 20 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 15 kN/m and k₂ = 5 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: T2 = 26.89 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: nr = 257.1 rpm
Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.
With nc = 0 the sun drives the ring through the planets, which act as idlers.
The ring turns opposite to the sun.
Answer: φ = 4.209 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: d = 64.35 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Both limits must hold, so the larger diameter governs.
Here stiffness governs.
Answer: θs = −56.75 °
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
On Mohr’s circle the top point (+R) is 90° from the principal point σ₁; on the element that is 45°.
Positive angles are counter-clockwise.
Answer: n = 2.767
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.
n > 1 means the point does not yield; Tresca is slightly more conservative than von Mises.
Answer: δ = 0.08079 mm
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: σ2 = 22.34 MPa
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: Pcr = 12.85 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: d = 153.3 mm
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Check: the slenderness KL/r is 313.2, so the column is slender and Euler applies.
Answer: ζ = 0.1429
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
ζ < 1, so the system is underdamped and oscillates as it decays.
Answer: keq = 20 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/machine-design