Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 7.5 kW motor running at 1450 rpm drives a pinion with 18 teeth, which meshes with a gear with 20 teeth. Ignore losses. Find the output torque T2 on the gear shaft.
An open belt connects a 120 mm pulley and a 300 mm pulley whose centres are 600 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.
A hollow brass shaft (outer diameter 75 mm, inner diameter 45 mm, length 2.5 m) is fixed at one end and twisted by a torque of 400 N·m at the other. Find the angle of twist φ in degrees.
A solid shaft must transmit 15 kW at 1000 rpm without the shear stress exceeding 40 MPa. Find the smallest diameter d that works.
A point has σₓ = 20 MPa and σᵧ = −20 MPa. How large can the shear stress τxy (magnitude) become before the largest principal stress reaches 65 MPa?
A point in a loaded part has σₓ = 90 MPa, σᵧ = −40 MPa and τₓᵧ = 60 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 15° counter-clockwise from the x-axis.
A steel rod (diameter 25 mm, E = 200 GPa) sits inside a tube made of brass (outer diameter 100 mm, inner diameter 60 mm, E = 100 GPa). Both are 800 mm long and are compressed together between rigid plates by 200 kN. Find the shortening δ.
The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.
A column of length L made of steel is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A column of length L made of steel is pinned at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.
In a free-vibration test of a damped mass–spring system, a displacement peak of 12 mm is followed 2 cycles later by a peak of 1.8 mm. Find the damping ratio ζ.
A 5 kg mass hangs from spring k₃ = 100 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 30 kN/m and k₂ = 50 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.
Answer: T2 = 54.88 N·m
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
Answer: θ = 162.7 °
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: φ = 0.5434 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: d = 26.32 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
In practice you would round up to the next standard size.
Answer: τxy = 61.85 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: σθ = 111.3 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: δ = 0.2663 mm
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: δ = 2.924 mm
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
Answer: Pcr = 2.481 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: σcr = 7.896 MPa
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: ζ = 0.1493
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 15.01 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.
ExamProblems · examproblems.com/courses/machine-design