Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
Two parallel shafts are 240 mm apart. They must be connected by a pair of spur gears with a module of 5 mm and a speed reduction of 3 : 1. How many teeth N1 must the pinion have?
In a compound gear train, gear A (40 teeth) on the input shaft turning at 1500 rpm drives gear B (80 teeth). Gear C (24 teeth) is fixed to the same shaft as B and drives gear D (32 teeth) on the output shaft. Find the output speed nout.
A solid brass shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.
A solid shaft must transmit 5 kW at 1450 rpm without the shear stress exceeding 50 MPa. Find the smallest diameter d that works.
A point in a loaded part has σₓ = 140 MPa, σᵧ = 120 MPa and τₓᵧ = 20 MPa (tension positive). Find the angle θp from the x-axis to the direction of the largest principal stress, between −90° and 90°.
A point in a thin plate is in plane stress: σₓ = −40 MPa, σᵧ = −20 MPa and τₓᵧ = −40 MPa (σz = 0). The material has a yield strength of 350 MPa. Find the factor of safety n against yielding by the von Mises (distortion energy) criterion.
Find the axial strain ε in the aluminium bar, in microstrain (µε = 10⁻⁶).
The stepped bar is fixed at the wall and loaded at its free end. Find the largest normal stress σmax in the bar.
A column of length L made of aluminium is fixed at the base and pinned at the top. Using Euler’s formula, find its critical buckling load Pcr.
A solid round column of length L made of steel is fixed at the base and pinned at the top. It must carry 125 kN with a factor of safety of 2 against buckling. Find the smallest diameter d.
A 5 kg mass on a spring with a stiffness of 40 kN/m has a viscous damper giving a damping ratio of 0.5. Find the damped natural frequency fd of its free vibration in Hz.
A 25 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 80 kN/m and the lower one k₂ = 10 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: N1 = 24
Gear geometry: the module m sets the tooth size. A gear with N teeth has a pitch diameter d = m·N, two meshing gears have the same module, and their centre distance is a = (d₁ + d₂)/2 = m·(N₁ + N₂)/2. The pitch-line speed is v = π·d·n/60, and the tangential tooth force follows from the torque: Ft = 2T/d.
Answer: nout = 562.5 rpm
Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.
total ratio = 2.667 : 1
Answer: φ = 1.437 °
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Answer: d = 14.97 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
In practice you would round up to the next standard size.
Answer: θp = 31.72 °
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Point x sits at an angle 2θp from the σ-axis on Mohr’s circle; the quadrant follows from the signs of σₓ − σᵧ and τₓᵧ.
Positive angles are counter-clockwise.
Answer: n = 4.518
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.
n > 1 means the point does not yield; Tresca is slightly more conservative than von Mises.
Answer: ε = 4547 µε
Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).
E for aluminium = 70 GPa = 70000 MPa.
Answer: σmax = 1017 MPa
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
The thinner segment has the smaller area, so it carries the larger stress.
Answer: Pcr = 18.05 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: d = 53.02 mm
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Check: the slenderness KL/r is 132, so the column is slender and Euler applies.
Answer: fd = 12.33 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 3.001 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/machine-design