Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 80 mmd2​ = 250 mm1440 rpmn2​ = ?

An 80 mm pulley at 1440 rpm drives a 250 mm pulley by a belt with 4 % slip. Find the speed n2 of the driven pulley.

n1 = 1440 rpmd1 = 80 mmd2 = 250 mms = 4 %
n2 = rpm
2.Gears & gear trainsHard
A = 18B = 24C = 16D = 80

In a compound gear train, gear A (18 teeth) on the input shaft turning at 2900 rpm drives gear B (24 teeth). Gear C (16 teeth) is fixed to the same shaft as B and drives gear D (80 teeth) on the output shaft. Find the output speed nout.

nin = 2900 rpmA = 18B = 24C = 16D = 80
nout = rpm
3.Torsion of shaftsMedium
T = 100 N·md = 50 mmL = 1.5 mφ = ?

A solid aluminium shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.

T = 100 N·md = 50 mmL = 1.5 mG = 26 GPa
φ = °
4.Torsion of shaftsHard
d = 30 mmT0​ = 1500 N·mACBa = 1.2 mb = 0.5 m

A solid aluminium shaft of diameter 30 mm is fixed to rigid walls at both ends A and B. A torque of 1500 N·m is applied at C, 1.2 m from A and 0.5 m from B. Find the reaction torque TA at wall A.

d = 30 mmT0 = 1500 N·ma = 1.2 mb = 0.5 m
TA = N·m
5.Mohr’s circle & stress transformationMedium
σx​ = −60σy​ = 120τxy​ = 30MPa

A point in a loaded part has σₓ = −60 MPa, σᵧ = 120 MPa and τₓᵧ = 30 MPa (tension positive). Find the maximum in-plane shear stress τmax.

σx = −60 MPaσy = 120 MPaτxy = 30 MPa
τmax = MPa
6.Mohr’s circle & stress transformationHard
30°D = 600 mm, t = 10 mm, p = 1 MPap

A thin-walled cylindrical tank of inner diameter 600 mm and wall thickness 10 mm holds gas at a gauge pressure of 1 MPa. It is made from plate welded along a helical seam at 30° to the axis of the cylinder. Find the normal stress σn acting across the weld seam.

D = 600 mmt = 10 mmp = 1 MPaα = 30°
σn = MPa
7.Axial stress & strainMedium
P = ?12600 mm300 mmØ40Ø30δ = 0.2 mm

A bar is made of a steel segment (diameter 40 mm, length 600 mm, E = 200 GPa) joined end to end with a segment made of aluminium (diameter 30 mm, length 300 mm, E = 70 GPa). It is fixed at one end and pulled at the other. Find the axial load P that stretches it by 0.2 mm in total.

segment 1: steel, Ø40 mm, 600 mm, E = 200 GPasegment 2: aluminium, Ø30 mm, 300 mm, E = 70 GPaδ = 0.2 mm
P = kN
8.Axial stress & strainHard
60 kN12500 mm400 mmØ25Ø40σ2​ = ?

A steel segment (diameter 25 mm, length 500 mm, E = 200 GPa) and a segment made of bronze (diameter 40 mm, length 400 mm, E = 110 GPa) are joined end to end and fixed between two rigid walls. An axial load of 60 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.

segment 1: steel, Ø25 mm, 500 mm, E = 200 GPasegment 2: bronze, Ø40 mm, 400 mm, E = 110 GPaP = 60 kN
σ2 = MPa
9.Column bucklingMedium
PL = 4 m30 × 100 mmcross-section

A column of length L made of steel is fixed at the base and pinned at the top. Using Euler’s formula, find its critical buckling load Pcr.

L = 4 mE = 200 GPa (steel)b × h = 30 × 100 mm
Pcr = kN
10.Column bucklingHard
PL = 3 md = 50 mmcross-section

A column of length L made of aluminium is fixed at the base and free at the top. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 3 mE = 70 GPa (aluminium)d = 50 mm
σcr = MPa
11.Mechanical vibrationsMedium
tx10 mm1 cycle8.8 mm

In a free-vibration test of a damped mass–spring system, a displacement peak of 10 mm is followed one cycle later by a peak of 8.8 mm. Find the damping ratio ζ.

x0 = 10 mmx1 = 8.8 mmn = 1
ζ =
12.Mechanical vibrationsHard
k1​ = 60k2​ = 25m = 10 kg

A 10 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 60 kN/m and the lower one k₂ = 25 kN/m. Find the equivalent stiffness keq of the spring system in kN/m.

m = 10 kgk1 = 60 kN/mk2 = 25 kN/m
keq = kN/m

3Solutions

1.Gears & gear trains

Answer: n2 = 442.4 rpm

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Speed without slip

1440·80/250 = 460.8 rpm

With slip

n2 = 460.8·0.96 = 442.4 rpm

Answer

n2 = 442.4 rpm
2.Gears & gear trains

Answer: nout = 435 rpm

Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.

First stage

nB = 2900·18/24 = 2175 rpm = nC

Second stage

nout = 2175·16/80 = 435 rpm

Answer

nout = 435 rpm

total ratio = 6.667 : 1

3.Torsion of shafts

Answer: φ = 0.5387 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Polar second moment of area

J = π·50⁴/32 = 613592 mm⁴

Angle of twist

φ = TL/(GJ) = 100·1000·1500/(26000·613592) = 0.009402 rad
φ = 0.009402·180/π = 0.5387°

Answer

φ = 0.5387°
4.Torsion of shafts

Answer: TA = 441.2 N·m

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω. When both ends are fixed, statics alone gives only TA + TB = T₀; the second equation is compatibility (equal twist of both parts at the loaded section).

Equilibrium and compatibility

TA + TB = 1500
TA·a = TB·b
TA = 1500·0.5/1.7 = 441.2 N·m
TB = 1500·1.2/1.7 = 1059 N·m

Answer

TA = 441.2 N·m
5.Mohr’s circle & stress transformation

Answer: τmax = 94.87 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCτmax​

Radius of Mohr’s circle

τmax = R = √(((−60 − 120)/2)² + 30²) = 94.87 MPa

Answer

τmax = 94.87 MPa
6.Mohr’s circle & stress transformation

Answer: σn = 26.25 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Thin-walled cylinder: hoop stress σh = pr/t and axial stress σa = pr/(2t); these are the principal stresses in the wall.

Wall stresses

r = 600/2 = 300 mm
σh = pr/t = 1·300/10 = 30 MPa
σa = pr/(2t) = 15 MPa

Transform to the seam

Take x along the axis (σa) and y around the hoop (σh). The seam’s normal makes 90° − α with the axis.

σn = 15·sin²30° + 30·cos²30° = 26.25 MPa

Answer

σn = 26.25 MPa
7.Axial stress & strain

Answer: P = 23.67 kN

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

A₁ = 1257 mm², A₂ = 706.9 mm²

Flexibilities

L₁/(E₁A₁) = 600/(200000·1257) = 2.387 × 10⁻⁶ mm/N
L₂/(E₂A₂) = 300/(70000·706.9) = 6.063 × 10⁻⁶ mm/N

Load

P = 0.2/8.45 × 10⁻⁶ = 23668 N = 23.67 kN

Answer

P = 23.67 kN
8.Axial stress & strain

Answer: σ2 = 30.45 MPa

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Stiffnesses

k₁ = 200000·490.9/500 = 196350 N/mm
k₂ = 110000·1257/400 = 345575 N/mm

Share of segment 2

F2 = 60000·345575/541925 = 38261 N

Stress

σ2 = 38261/1257 = 30.45 MPa (compression)

Answer

σ2 = 30.45 MPa
9.Column buckling

Answer: Pcr = 56.65 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A rectangle buckles about its weak axis, using the smaller dimension cubed.

Imin = h·b³/12 = 100·30³/12 = 225000 mm⁴

Effective length

KL = 0.7·4000 = 2800 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·225000/2800² = 56650 N = 56.65 kN

Answer

Pcr = 56.65 kN
10.Column buckling

Answer: σcr = 2.999 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·50⁴/64 = 306796 mm⁴

Radius of gyration and slenderness

A = 1963 mm²
r = √(I/A) = √(306796/1963) = 12.5 mm
KL = 2·3000 = 6000 mm
KL/r = 6000/12.5 = 480

Critical stress

σcr = π²E/(KL/r)² = π²·70000/480² = 2.999 MPa

Answer

σcr = 2.999 MPa
11.Mechanical vibrations

Answer: ζ = 0.02034

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Logarithmic decrement

δ = (1/1)·ln(10/8.8) = 0.1278

Damping ratio

ζ = δ/√(4π² + δ²) = 0.1278/√(39.48 + 0.01634) = 0.02034

Answer

ζ = 0.02034
12.Mechanical vibrations

Answer: keq = 17.65 kN/m

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.

1/keq = 1/60 + 1/25 → keq = 60·25/(60 + 25) = 17.65 kN/m

Answer

keq = 17.65 kN/m

ExamProblems · examproblems.com/courses/machine-design