Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 120 mmd2​ = 400 mm1440 rpmT1​ = 800 NT2​ = 200 NP = ?

A belt runs on a 120 mm driving pulley at 1440 rpm. The tension is 800 N on the tight side and 200 N on the slack side. Find the power P transmitted, in kW.

d1 = 120 mmn1 = 1440 rpmT1 = 800 NT2 = 200 N
P = kW
2.Gears & gear trainsHard
A = 45B = 48C = 18D = ?

In a compound gear train, gear A (45 teeth) on the input shaft turns at 960 rpm and drives gear B (48 teeth). Gear C (18 teeth) is fixed to the same shaft as B and drives gear D on the output shaft. The output must turn at 324 rpm. How many teeth ND must gear D have?

nin = 960 rpmA = 45B = 48C = 18nout = 324 rpm
ND =
3.Torsion of shaftsMedium
d = 20 mmT = 40 N·m250 mmφ = 0.94°

In a torsion test, a solid specimen of diameter 20 mm is twisted by a torque of 40 N·m. The two ends of a gauge length of 250 mm rotate 0.94° relative to each other (the material is still elastic). Find the shear modulus G of the material.

T = 40 N·md = 20 mmL = 250 mmφ = 0.94°
G = GPa
4.Torsion of shaftsHard
d = 30 mmTB​ = 100 N·mTC​ = 250 N·mABC2 m1.2 m

A solid steel shaft of diameter 30 mm is fixed at A. A torque of 100 N·m acts at B, 2 m from A, and a torque of 250 N·m in the opposite direction acts at the free end C, a further 1.2 m along. Find the magnitude of the angle of twist φC of end C, in degrees.

d = 30 mmTB = 100 N·mTC = 250 N·mAB = 2 mBC = 1.2 mG = 80 GPa
φC = °
5.Mohr’s circle & stress transformationMedium
σx​ = 0σy​ = 110τxy​ = 60MPa

A point in a loaded part has σₓ = 0 MPa, σᵧ = 110 MPa and τₓᵧ = 60 MPa (tension positive). Find the angle θp from the x-axis to the direction of the largest principal stress, between −90° and 90°.

σx = 0 MPaσy = 110 MPaτxy = 60 MPa
θp = °
6.Mohr’s circle & stress transformationHard
σx​τxy​top surface of the shaft

A solid shaft of diameter 30 mm carries a bending moment of 1000 N·m together with a torque of 400 N·m. At the top surface, where the bending stress is tensile and largest, find the largest principal stress σ1.

d = 30 mmM = 1000 N·mT = 400 N·m
σ1 = MPa
7.Axial stress & strainMedium
200 kNØ40100 GPaØ80/60500 mmδ = ?

A steel rod (diameter 40 mm, E = 200 GPa) sits inside a tube made of brass (outer diameter 80 mm, inner diameter 60 mm, E = 100 GPa). Both are 500 mm long and are compressed together between rigid plates by 200 kN. Find the shortening δ.

P = 200 kNrod: Ø40 mm, E = 200 GPatube: Ø80/Ø60 mm, E = 100 GPaL = 500 mm
δ = mm
8.Axial stress & strainHard
60 kN12300 mm400 mmØ30Ø50σ2​ = ?

A steel segment (diameter 30 mm, length 300 mm, E = 200 GPa) and a segment made of copper (diameter 50 mm, length 400 mm, E = 120 GPa) are joined end to end and fixed between two rigid walls. An axial load of 60 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.

segment 1: steel, Ø30 mm, 300 mm, E = 200 GPasegment 2: copper, Ø50 mm, 400 mm, E = 120 GPaP = 60 kN
σ2 = MPa
9.Column bucklingMedium
PL = 2 m25 × 100 mmcross-section

A column of length L made of steel is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.

L = 2 mE = 200 GPa (steel)b × h = 25 × 100 mm
Pcr = kN
10.Column bucklingHard
PL = 1 md = 25 mmcross-section

A column of length L made of aluminium is pinned at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 1 mE = 70 GPa (aluminium)d = 25 mm
σcr = MPa
11.Mechanical vibrationsMedium
tx50 mm5 cycles1.1 mm

In a free-vibration test of a damped mass–spring system, a displacement peak of 50 mm is followed 5 cycles later by a peak of 1.1 mm. Find the damping ratio ζ.

x0 = 50 mmx5 = 1.1 mmn = 5
ζ =
12.Mechanical vibrationsHard
k1​ = 12k2​ = 20m = 20 kg

A 20 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 12 kN/m and k₂ = 20 kN/m. The mass stays level. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.

m = 20 kgk1 = 12 kN/mk2 = 20 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: P = 5.429 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt speed

v = 9.048 m/s

Power

P = (800 − 200)·9.048 = 5429 W = 5.429 kW

Answer

P = 5.429 kW
2.Gears & gear trains

Answer: ND = 50

Gear trains: meshing gears have the same speed at the teeth, so n₁·N₁ = n₂·N₂: the gear with fewer teeth turns faster. Gears on one shaft turn at the same speed. Power is passed on (minus losses), so torque goes up when speed goes down: T₂ = T₁·(N₂/N₁)·η, and P = T·ω with ω = 2π·n/60.

Intermediate shaft speed

nB = nC = 960·45/48 = 900 rpm

Teeth on gear D

ND = C·nC/nout = 18·900/324 = 50

Answer

ND = 50
3.Torsion of shafts

Answer: G = 38.8 GPa

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Polar moment and angle

J = π·20⁴/32 = 15708 mm⁴
φ = 0.94·π/180 = 0.01641 rad

Shear modulus

T = 40 N·m = 40000 N·mm
G = TL/(Jφ) = 40000·250/(15708·0.01641) = 38804 MPa
G = 38.8 GPa

Answer

G = 38.8 GPa

Compare: steel ≈ 80 GPa, brass ≈ 39 GPa, aluminium ≈ 26 GPa.

4.Torsion of shafts

Answer: φC = 5.404 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Internal torques

Sense of TC taken as positive.

TBC = TC = 250 N·m
TAB = TC − TB = 250 − 100 = 150 N·m

Twist of each segment

J = π·30⁴/32 = 79522 mm⁴
G = 80 GPa = 80000 MPa
φAB = 150000·2000/(80000·79522) = 0.04716 rad
φBC = 250000·1200/(80000·79522) = 0.04716 rad

Twist of end C

φC = 0.04716 + 0.04716 = 0.09431 rad → |φC| = 5.404°

Answer

φC = 5.404°
5.Mohr’s circle & stress transformation

Answer: θp = 66.26 °

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCσ1​σ2​

Angle on the circle

Point x sits at an angle 2θp from the σ-axis on Mohr’s circle; the quadrant follows from the signs of σₓ − σᵧ and τₓᵧ.

2θp = atan2(2·60, 0 − 110) = 132.5°

Angle on the element

θp = 66.26°

Answer

θp = 66.26°

Positive angles are counter-clockwise.

6.Mohr’s circle & stress transformation

Answer: σ1 = 391.8 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Stresses at the surface

σ = 32M/(πd³) = 32·1000000/(π·30³) = 377.3 MPa
τ = 16T/(πd³) = 16·400000/(π·30³) = 75.45 MPa
στxyCσ1​σ2​

Mohr’s circle

C = σ/2 = 188.6 MPa
R = √(188.6² + 75.45²) = 203.2 MPa
σ1 = C + R = 391.8 MPa
σ2 = C − R = −14.53 MPa

Answer

σ1 = 391.8 MPa
7.Axial stress & strain

Answer: δ = 0.2122 mm

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

Ar = π·40²/4 = 1257 mm²
At = π(80² − 60²)/4 = 2199 mm²

Combined axial stiffness

ΣEA = 200·10³·1257 + 100·10³·2199 = 4.712 × 10⁸ N

Shortening

δ = 200000·500/4.712 × 10⁸ = 0.2122 mm

Answer

δ = 0.2122 mm
8.Axial stress & strain

Answer: σ2 = 16.98 MPa

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Stiffnesses

k₁ = 200000·706.9/300 = 471239 N/mm
k₂ = 120000·1963/400 = 589049 N/mm

Share of segment 2

F2 = 60000·589049/1.06 × 10⁶ = 33333 N

Stress

σ2 = 33333/1963 = 16.98 MPa (compression)

Answer

σ2 = 16.98 MPa
9.Column buckling

Answer: Pcr = 16.06 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A rectangle buckles about its weak axis, using the smaller dimension cubed.

Imin = h·b³/12 = 100·25³/12 = 130208 mm⁴

Effective length

KL = 2·2000 = 4000 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·130208/4000² = 16064 N = 16.06 kN

Answer

Pcr = 16.06 kN
10.Column buckling

Answer: σcr = 26.99 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·25⁴/64 = 19175 mm⁴

Radius of gyration and slenderness

A = 490.9 mm²
r = √(I/A) = √(19175/490.9) = 6.25 mm
KL = 1·1000 = 1000 mm
KL/r = 1000/6.25 = 160

Critical stress

σcr = π²E/(KL/r)² = π²·70000/160² = 26.99 MPa

Answer

σcr = 26.99 MPa
11.Mechanical vibrations

Answer: ζ = 0.1206

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Logarithmic decrement

δ = (1/5)·ln(50/1.1) = 0.7633

Damping ratio

ζ = δ/√(4π² + δ²) = 0.7633/√(39.48 + 0.5827) = 0.1206

Answer

ζ = 0.1206
12.Mechanical vibrations

Answer: fn = 6.366 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.

keq = 12 + 20 = 32 kN/m

Natural frequency

ωn = √(32000/20) = 40 rad/s
fn = 40/(2π) = 6.366 Hz

Answer

fn = 6.366 Hz

ExamProblems · examproblems.com/courses/machine-design