Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A belt runs on a 160 mm driving pulley at 2880 rpm. The tension is 400 N on the tight side and 100 N on the slack side. Find the power P transmitted, in kW.
An open belt connects a 160 mm driving pulley at 1450 rpm to a 300 mm pulley; the centres are 1000 mm apart. The coefficient of friction is 0.35 and the tight-side tension may not exceed 2000 N. Find the largest power P the belt can transmit without slipping, in kW (ignore centrifugal effects).
In a torsion test, a solid specimen of diameter 15 mm is twisted by a torque of 20 N·m. The two ends of a gauge length of 250 mm rotate 1.48° relative to each other (the material is still elastic). Find the shear modulus G of the material.
A solid steel shaft transmits 50 kW at 500 rpm. The shear stress must not exceed 80 MPa and the twist must not exceed 0.75° per m of length. Find the smallest diameter d that satisfies both limits.
A point has σₓ = 50 MPa and σᵧ = 50 MPa. How large can the shear stress τxy (magnitude) become before the largest principal stress reaches 105 MPa?
A point in a thin plate is in plane stress: σₓ = 90 MPa, σᵧ = −20 MPa and τₓᵧ = 30 MPa (σz = 0). The material has a yield strength of 420 MPa. Find the factor of safety n against yielding by the Tresca (maximum shear stress) criterion.
A steel rod (diameter 20 mm, E = 200 GPa) sits inside a tube made of brass (outer diameter 80 mm, inner diameter 50 mm, E = 100 GPa). Both are 600 mm long and are compressed together between rigid plates by 250 kN. Find the shortening δ.
The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.
A column of length L made of steel is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.
A solid round column of length L made of aluminium is pinned at both ends. It must carry 45 kN with a factor of safety of 2.5 against buckling. Find the smallest diameter d.
A 12 kg mass on a spring with a stiffness of 200 kN/m has a viscous damper giving a damping ratio of 0.3. Find the damped natural frequency fd of its free vibration in Hz.
A 25 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 40 kN/m and k₂ = 12 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: P = 7.238 kW
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: P = 15.8 kW
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: G = 38.95 GPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Compare: steel ≈ 80 GPa, brass ≈ 39 GPa, aluminium ≈ 26 GPa.
Answer: d = 55.21 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Both limits must hold, so the larger diameter governs.
Here stiffness governs.
Answer: τxy = 55 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: n = 3.352
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.
n > 1 means the point does not yield; Tresca is slightly more conservative than von Mises.
Answer: δ = 0.4064 mm
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: δ = 4.037 mm
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
Answer: Pcr = 14.28 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: d = 95.43 mm
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Check: the slenderness KL/r is 209.6, so the column is slender and Euler applies.
Answer: fd = 19.6 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 52 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.
ExamProblems · examproblems.com/courses/machine-design