Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 120 mmd2​ = 500 mm1500 rpmT1​ = 800 NT2​ = 240 NP = ?

A belt runs on a 120 mm driving pulley at 1500 rpm. The tension is 800 N on the tight side and 240 N on the slack side. Find the power P transmitted, in kW.

d1 = 120 mmn1 = 1500 rpmT1 = 800 NT2 = 240 N
P = kW
2.Gears & gear trainsHard
Ns​ = 15ring fixedNp​ = 15nc​ = ?

In a planetary gear set the sun gear has 15 teeth and each planet gear has 15 teeth. The ring gear is held fixed and the sun is driven at 1200 rpm. Find the speed nc of the planet carrier.

Ns = 15Np = 15ns = 1200 rpm
nc = rpm
3.Torsion of shaftsMedium
T = 500 N·md = 50 mmL = 1.5 mφ = ?

A solid aluminium shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.

T = 500 N·md = 50 mmL = 1.5 mG = 26 GPa
φ = °
4.Torsion of shaftsHard
do​ = ?50 kW, 1450 rpm

A hollow shaft must transmit 50 kW at 1450 rpm. Its inner diameter is to be 0.8 times its outer diameter, and the shear stress must not exceed 75 MPa. Find the smallest outer diameter do.

P = 50 kWN = 1450 rpmdi/do = 0.8τallow = 75 MPa
do = mm
5.Mohr’s circle & stress transformationMedium
σx​ = −30σy​ = 60MPaτxy​ = ?

A point has σₓ = −30 MPa and σᵧ = 60 MPa. How large can the shear stress τxy (magnitude) become before the largest principal stress reaches 90 MPa?

σx = −30 MPaσy = 60 MPaσ1 = 90 MPa
τxy = MPa
6.Mohr’s circle & stress transformationHard
σx​ = −80σy​ = 100τxy​ = 10MPa

A point in a thin plate is in plane stress: σₓ = −80 MPa, σᵧ = 100 MPa and τₓᵧ = 10 MPa (σz = 0). The material has a yield strength of 350 MPa. Find the factor of safety n against yielding by the von Mises (distortion energy) criterion.

σx = −80 MPaσy = 100 MPaτxy = 10 MPaσY = 350 MPa
n =
7.Axial stress & strainMedium
300 kNØ2570 GPaØ100/50600 mmδ = ?

A steel rod (diameter 25 mm, E = 200 GPa) sits inside a tube made of aluminium (outer diameter 100 mm, inner diameter 50 mm, E = 70 GPa). Both are 600 mm long and are compressed together between rigid plates by 300 kN. Find the shortening δ.

P = 300 kNrod: Ø25 mm, E = 200 GPatube: Ø100/Ø50 mm, E = 70 GPaL = 600 mm
δ = mm
8.Axial stress & strainHard
P = ?Ø25120 GPaØ120/70800 mm

A steel rod (diameter 25 mm, E = 200 GPa, allowable stress 250 MPa) sits inside a tube made of copper (outer diameter 120 mm, inner diameter 70 mm, E = 120 GPa, allowable stress 80 MPa). They are compressed together between rigid plates. Find the largest load Pmax.

rod: Ø25 mm, E = 200 GPa, σallow = 250 MPatube: Ø120/Ø70 mm, E = 120 GPa, σallow = 80 MPa
Pmax = kN
9.Column bucklingMedium
PL = 5 md = 80 mmcross-section

A column of length L made of steel is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 5 mE = 200 GPa (steel)d = 80 mm
Pcr = kN
10.Column bucklingHard
P = 55 kNL = 2.5 md = ?cross-section

A solid round column of length L made of steel is fixed at the base and free at the top. It must carry 55 kN with a factor of safety of 2 against buckling. Find the smallest diameter d.

P = 55 kNn = 2L = 2.5 mE = 200 GPa (steel)
d = mm
11.Mechanical vibrationsMedium
k = 8 kN/mc = 170 N·s/mm = 10 kg

A 10 kg mass is supported by a spring with a stiffness of 8 kN/m and a viscous damper with a damping coefficient of 170 N·s/m. Find the damping ratio ζ.

m = 10 kgk = 8 kN/mc = 170 N·s/m
ζ =
12.Mechanical vibrationsHard
k1​ = 20k2​ = 30m = 10 kg

A 10 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 20 kN/m and the lower one k₂ = 30 kN/m. Find the equivalent stiffness keq of the spring system in kN/m.

m = 10 kgk1 = 20 kN/mk2 = 30 kN/m
keq = kN/m

3Solutions

1.Gears & gear trains

Answer: P = 5.278 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt speed

v = 9.425 m/s

Power

P = (800 − 240)·9.425 = 5278 W = 5.278 kW

Answer

P = 5.278 kW
2.Gears & gear trains

Answer: nc = 300 rpm

Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.

Ring gear teeth

Nr = Ns + 2·Np = 15 + 2·15 = 45

Willis equation with the ring fixed

Set nr = 0 and solve for the carrier speed.

(1200 − nc)/(0 − nc) = −45/15
nc = ns·Ns/(Ns + Nr) = 1200·15/60 = 300 rpm

Answer

nc = 300 rpm

The carrier turns in the same direction as the sun.

3.Torsion of shafts

Answer: φ = 2.694 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Polar second moment of area

J = π·50⁴/32 = 613592 mm⁴

Angle of twist

φ = TL/(GJ) = 500·1000·1500/(26000·613592) = 0.04701 rad
φ = 0.04701·180/π = 2.694°

Answer

φ = 2.694°
4.Torsion of shafts

Answer: do = 33.58 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Torque

ω = 2πN/60 = 2π·1450/60 = 151.8 rad/s
T = P/ω = 50000/151.8 = 329.3 N·m

Outer diameter from the allowable stress

T = 329.3 N·m = 329286 N·mm
1 − k⁴ = 1 − 0.8⁴ = 0.5904
do = ∛(16T/(π·τallow·(1 − k⁴))) = ∛(16·329286/(π·75·0.5904)) = 33.58 mm
di = 0.8·33.58 = 26.87 mm

Answer

do = 33.58 mm

A solid shaft would need d = 28.17 mm; the hollow one is a little larger but much lighter.

5.Mohr’s circle & stress transformation

Answer: τxy = 60 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Required radius

C = (−30 + 60)/2 = 15 MPa
R = σ1 − C = 90 − 15 = 75 MPa
στxyCσ1​σ2​

Shear stress

τxy = √(R² − ((σₓ − σᵧ)/2)²) = √(75² − 45²) = 60 MPa

Answer

τxy = 60 MPa
6.Mohr’s circle & stress transformation

Answer: n = 2.227

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.

στxyCσ1​σ2​

Principal stresses

C = 10 MPa, R = 90.55 MPa
σ1 = 100.6 MPa, σ2 = −80.55 MPa, σ3 = 0

Von Mises

σvM = √(100.6² − 100.6·(−80.55) + (−80.55)²) = 157.2 MPa
n = 350/157.2 = 2.227

Answer

n = 2.227

n > 1 means the point does not yield; Tresca is slightly more conservative than von Mises.

7.Axial stress & strain

Answer: δ = 0.3526 mm

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

Ar = π·25²/4 = 490.9 mm²
At = π(100² − 50²)/4 = 5890 mm²

Combined axial stiffness

ΣEA = 200·10³·490.9 + 70·10³·5890 = 5.105 × 10⁸ N

Shortening

δ = 300000·600/5.105 × 10⁸ = 0.3526 mm

Answer

δ = 0.3526 mm
8.Axial stress & strain

Answer: Pmax = 662.4 kN

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

Ar = π·25²/4 = 490.9 mm²
At = π(120² − 70²)/4 = 7461 mm²

Combined axial stiffness

ΣEA = 200·10³·490.9 + 120·10³·7461 = 9.935 × 10⁸ N

Governing strain

ε = min(0.00125, 0.0006667) = 0.0006667 (copper)

Largest load

Pmax = 0.0006667·9.935 × 10⁸ = 662352 N = 662.4 kN

Answer

Pmax = 662.4 kN
9.Column buckling

Answer: Pcr = 635 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·80⁴/64 = 2.011 × 10⁶ mm⁴

Effective length

KL = 0.5·5000 = 2500 mm

Critical load

Pcr = π²EI/(KL)² = π²·200000·2.011 × 10⁶/2500² = 635009 N = 635 kN

Answer

Pcr = 635 kN
10.Column buckling

Answer: d = 72.99 mm

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Required critical load

Pcr = n·P = 2·55000 = 110000 N
KL = 2·2500 = 5000 mm

Solve for the diameter

d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·110000·5000²/(π³·200000))^(1/4) = 72.99 mm

Answer

d = 72.99 mm

Check: the slenderness KL/r is 274, so the column is slender and Euler applies.

11.Mechanical vibrations

Answer: ζ = 0.3005

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Critical damping

cc = 2·√(k·m) = 2·√(8000·10) = 565.7 N·s/m

Damping ratio

ζ = c/cc = 170/565.7 = 0.3005

Answer

ζ = 0.3005

ζ < 1, so the system is underdamped and oscillates as it decays.

12.Mechanical vibrations

Answer: keq = 12 kN/m

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.

1/keq = 1/20 + 1/30 → keq = 20·30/(20 + 30) = 12 kN/m

Answer

keq = 12 kN/m

ExamProblems · examproblems.com/courses/machine-design