Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 100 mmd2​ = 250 mm1440 rpmn2​ = ?

A 100 mm pulley at 1440 rpm drives a 250 mm pulley by a belt with 2.5 % slip. Find the speed n2 of the driven pulley.

n1 = 1440 rpmd1 = 100 mmd2 = 250 mms = 2.5 %
n2 = rpm
2.Gears & gear trainsHard
d1​ = 80 mmd2​ = 200 mm1440 rpmC = 500 mmθ = ?

An open belt connects an 80 mm pulley and a 200 mm pulley whose centres are 500 mm apart. Find the angle of wrap θ on the smaller pulley, in degrees.

d1 = 80 mmd2 = 200 mmC = 500 mm
θ = °
3.Torsion of shaftsMedium
do​ = ?T = 250 N·m

A hollow shaft must carry a torque of 250 N·m. Its inner diameter is to be 0.7 times its outer diameter, and the shear stress must not exceed 40 MPa. Find the smallest outer diameter do.

T = 250 N·mdi/do = 0.7τallow = 40 MPa
do = mm
4.Torsion of shaftsHard
do​ = ?50 kW, 750 rpm

A hollow shaft must transmit 50 kW at 750 rpm. Its inner diameter is to be 0.6 times its outer diameter, and the shear stress must not exceed 40 MPa. Find the smallest outer diameter do.

P = 50 kWN = 750 rpmdi/do = 0.6τallow = 40 MPa
do = mm
5.Mohr’s circle & stress transformationMedium
σx​ = −80σy​ = 110τxy​ = −40MPa

A point in a loaded part has σₓ = −80 MPa, σᵧ = 110 MPa and τₓᵧ = −40 MPa (tension positive). Find the angle θp from the x-axis to the direction of the largest principal stress, between −90° and 90°.

σx = −80 MPaσy = 110 MPaτxy = −40 MPa
θp = °
6.Mohr’s circle & stress transformationHard
σx​ = −70σy​ = −70τxy​ = −50MPa

A point in a thin plate is in plane stress: σₓ = −70 MPa, σᵧ = −70 MPa and τₓᵧ = −50 MPa (σz = 0). The material has a yield strength of 420 MPa. Find the factor of safety n against yielding by the Tresca (maximum shear stress) criterion.

σx = −70 MPaσy = −70 MPaτxy = −50 MPaσY = 420 MPa
n =
7.Axial stress & strainMedium
Ø 30 mmBrass1.5 mP = 85 kN

Find the elongation δ of the brass bar under the axial load.

P = 85 kNd = 30 mmL = 1.5 mE = 100 GPa
δ = mm
8.Axial stress & strainHard
P = ?Ø40100 GPaØ120/50600 mm

A steel rod (diameter 40 mm, E = 200 GPa, allowable stress 150 MPa) sits inside a tube made of brass (outer diameter 120 mm, inner diameter 50 mm, E = 100 GPa, allowable stress 60 MPa). They are compressed together between rigid plates. Find the largest load Pmax.

rod: Ø40 mm, E = 200 GPa, σallow = 150 MPatube: Ø120/Ø50 mm, E = 100 GPa, σallow = 60 MPa
Pmax = kN
9.Column bucklingMedium
PL = 4 md = 40 mmcross-section

A column of length L made of aluminium is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 4 mE = 70 GPa (aluminium)d = 40 mm
Pcr = kN
10.Column bucklingHard
PL = 4 md = 50 mmcross-section

A column of length L made of aluminium is fixed at both ends. Find its slenderness and the critical buckling stress σcr from Euler’s formula.

L = 4 mE = 70 GPa (aluminium)d = 50 mm
σcr = MPa
11.Mechanical vibrationsMedium
k = 25 kN/mc = 500 N·s/mm = 40 kg

A 40 kg mass is supported by a spring with a stiffness of 25 kN/m and a viscous damper with a damping coefficient of 500 N·s/m. Find the damping ratio ζ.

m = 40 kgk = 25 kN/mc = 500 N·s/m
ζ =
12.Mechanical vibrationsHard
k1​ = 10k2​ = 60k3​ = 50m = 20 kg

A 20 kg mass hangs from spring k₃ = 50 kN/m. The top of k₃ is attached to a rigid bar that hangs from two springs side by side, k₁ = 10 kN/m and k₂ = 60 kN/m; the bar stays level. Ignore damping and the masses of the springs and bar. Find the natural frequency fn of vertical vibration in Hz.

m = 20 kgk1 = 10 kN/mk2 = 60 kN/mk3 = 50 kN/m
fn = Hz

3Solutions

1.Gears & gear trains

Answer: n2 = 561.6 rpm

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Speed without slip

1440·100/250 = 576 rpm

With slip

n2 = 576·0.975 = 561.6 rpm

Answer

n2 = 561.6 rpm
2.Gears & gear trains

Answer: θ = 166.2 °

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt angle

asin(0.12) = 6.892°

Angle of wrap

θ = 180 − 2·6.892 = 166.2°

Answer

θ = 166.2°
3.Torsion of shafts

Answer: do = 34.73 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Outer diameter from the allowable stress

T = 250 N·m = 250000 N·mm
1 − k⁴ = 1 − 0.7⁴ = 0.7599
do = ∛(16T/(π·τallow·(1 − k⁴))) = ∛(16·250000/(π·40·0.7599)) = 34.73 mm
di = 0.7·34.73 = 24.31 mm

Answer

do = 34.73 mm

A solid shaft would need d = 31.69 mm; the hollow one is a little larger but much lighter.

4.Torsion of shafts

Answer: do = 45.33 mm

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Torque

ω = 2πN/60 = 2π·750/60 = 78.54 rad/s
T = P/ω = 50000/78.54 = 636.6 N·m

Outer diameter from the allowable stress

T = 636.6 N·m = 636620 N·mm
1 − k⁴ = 1 − 0.6⁴ = 0.8704
do = ∛(16T/(π·τallow·(1 − k⁴))) = ∛(16·636620/(π·40·0.8704)) = 45.33 mm
di = 0.6·45.33 = 27.2 mm

Answer

do = 45.33 mm

A solid shaft would need d = 43.28 mm; the hollow one is a little larger but much lighter.

5.Mohr’s circle & stress transformation

Answer: θp = −78.58 °

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

στxyCσ1​σ2​

Angle on the circle

Point x sits at an angle 2θp from the σ-axis on Mohr’s circle; the quadrant follows from the signs of σₓ − σᵧ and τₓᵧ.

2θp = atan2(2·−40, −80 − 110) = −157.2°

Angle on the element

θp = −78.58°

Answer

θp = −78.58°

Positive angles are counter-clockwise.

6.Mohr’s circle & stress transformation

Answer: n = 3.5

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.

στxyCσ1​σ2​

Principal stresses

C = −70 MPa, R = 50 MPa
σ1 = −20 MPa, σ2 = −120 MPa, σ3 = 0

Tresca

σmax − σmin = 120 MPa
n = 420/120 = 3.5

Answer

n = 3.5

n > 1 means the point does not yield; Tresca is slightly more conservative than von Mises.

7.Axial stress & strain

Answer: δ = 1.804 mm

Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).

Stress

A = π·30²/4 = 706.9 mm²
σ = P/A = 85·1000/706.9 = 120.3 MPa

Strain (Hooke’s law)

E for brass = 100 GPa = 100000 MPa.

ε = σ/E = 120.3/100000 = 0.001203 = 1203 µε

Elongation

δ = ε·L = 0.001203·1500 mm = 1.804 mm

Answer

δ = 1.804 mm
8.Axial stress & strain

Answer: Pmax = 711.6 kN

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

Ar = π·40²/4 = 1257 mm²
At = π(120² − 50²)/4 = 9346 mm²

Combined axial stiffness

ΣEA = 200·10³·1257 + 100·10³·9346 = 1.186 × 10⁹ N

Governing strain

ε = min(0.00075, 0.0006) = 0.0006 (brass)

Largest load

Pmax = 0.0006·1.186 × 10⁹ = 711571 N = 711.6 kN

Answer

Pmax = 711.6 kN
9.Column buckling

Answer: Pcr = 21.7 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·40⁴/64 = 125664 mm⁴

Effective length

KL = 0.5·4000 = 2000 mm

Critical load

Pcr = π²EI/(KL)² = π²·70000·125664/2000² = 21704 N = 21.7 kN

Answer

Pcr = 21.7 kN
10.Column buckling

Answer: σcr = 26.99 MPa

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·50⁴/64 = 306796 mm⁴

Radius of gyration and slenderness

A = 1963 mm²
r = √(I/A) = √(306796/1963) = 12.5 mm
KL = 0.5·4000 = 2000 mm
KL/r = 2000/12.5 = 160

Critical stress

σcr = π²E/(KL/r)² = π²·70000/160² = 26.99 MPa

Answer

σcr = 26.99 MPa
11.Mechanical vibrations

Answer: ζ = 0.25

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Critical damping

cc = 2·√(k·m) = 2·√(25000·40) = 2000 N·s/m

Damping ratio

ζ = c/cc = 500/2000 = 0.25

Answer

ζ = 0.25

ζ < 1, so the system is underdamped and oscillates as it decays.

12.Mechanical vibrations

Answer: fn = 6.078 Hz

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Only k1 and k2 are in parallel. That pair is in series with k3, so combine them as reciprocals.

k12 = 10 + 60 = 70 kN/m
keq = 70·50/(70 + 50) = 29.17 kN/m

Natural frequency

ωn = √(29167/20) = 38.19 rad/s
fn = 38.19/(2π) = 6.078 Hz

Answer

fn = 6.078 Hz

ExamProblems · examproblems.com/courses/machine-design