Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A belt runs on a 120 mm driving pulley at 1450 rpm. The tension is 1000 N on the tight side and 250 N on the slack side. Find the power P transmitted, in kW.
In a planetary gear set the sun gear has 16 teeth and each planet gear has 15 teeth. The planet carrier is held fixed and the sun is driven at 1200 rpm. Find the speed nr of the ring gear (magnitude).
A solid brass shaft 2.5 m long carries a torque of 500 N·m. The angle of twist between its ends must not exceed 1°. Find the smallest diameter d that meets this limit.
A solid shaft must transmit 50 kW at 1000 rpm without the shear stress exceeding 50 MPa. Find the smallest diameter d that works.
A point in a thin plate is in plane stress: σₓ = 40 MPa, σᵧ = 90 MPa and τₓᵧ = 20 MPa, with σz = 0. Find the absolute maximum shear stress τabs at the point (considering all planes in three dimensions).
A point in a loaded part has σₓ = 130 MPa, σᵧ = −80 MPa and τₓᵧ = 30 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 35° counter-clockwise from the x-axis.
A bar is made of a steel segment (diameter 30 mm, length 600 mm, E = 200 GPa) joined end to end with a segment made of copper (diameter 40 mm, length 200 mm, E = 120 GPa). It is fixed at one end and pulled at the other. Find the axial load P that stretches it by 0.2 mm in total.
A steel segment (diameter 20 mm, length 500 mm, E = 200 GPa) and a segment made of bronze (diameter 40 mm, length 300 mm, E = 110 GPa) are joined end to end and fixed between two rigid walls. An axial load of 50 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.
A column of length L made of aluminium is fixed at the base and free at the top. Using Euler’s formula, find its critical buckling load Pcr.
A solid round column of length L made of aluminium is fixed at the base and pinned at the top. It must carry 140 kN with a factor of safety of 2.5 against buckling. Find the smallest diameter d.
In a free-vibration test of a damped mass–spring system, a displacement peak of 15 mm is followed 3 cycles later by a peak of 5.8 mm. Find the damping ratio ζ.
A 10 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 10 kN/m and the lower one k₂ = 25 kN/m. Find the equivalent stiffness keq of the spring system in kN/m.
Answer: P = 6.833 kW
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: nr = 417.4 rpm
Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.
With nc = 0 the sun drives the ring through the planets, which act as idlers.
The ring turns opposite to the sun.
Answer: d = 65.76 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
In practice you would round up to the next standard size.
Answer: d = 36.5 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
In practice you would round up to the next standard size.
Answer: τabs = 48.51 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. In three dimensions the absolute maximum shear stress is (σmax − σmin)/2 over all three principal stresses; in plane stress the third one is zero.
Here the out-of-plane circle governs: the absolute maximum is larger than the in-plane maximum R.
Answer: σθ = 89.1 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: P = 35.9 kN
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: σ2 = 31.26 MPa
Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.
Answer: Pcr = 47.98 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A rectangle buckles about its weak axis, using the smaller dimension cubed.
Answer: d = 116.2 mm
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Check: the slenderness KL/r is 144.6, so the column is slender and Euler applies.
Answer: ζ = 0.05035
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: keq = 7.143 kN/m
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/machine-design