Gears & gear trains
- Meshing gears
- n1·N1 = n2·N2
- Torque
- T2 = T1·(N2/N1)·η
- Power
- P = T·ω, ω = 2π·n/60
- Compound train
- total ratio = product of the stage ratios
Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.
A 125 mm pulley at 1440 rpm drives a 200 mm pulley by a belt with 4 % slip. Find the speed n2 of the driven pulley.
An open belt connects a 200 mm driving pulley at 1440 rpm to a 500 mm pulley; the centres are 500 mm apart. The coefficient of friction is 0.25 and the tight-side tension may not exceed 1000 N. Find the largest power P the belt can transmit without slipping, in kW (ignore centrifugal effects).
In a torsion test, a solid specimen of diameter 10 mm is twisted by a torque of 40 N·m. The two ends of a gauge length of 400 mm rotate 11.67° relative to each other (the material is still elastic). Find the shear modulus G of the material.
A solid steel shaft transmits 20 kW at 1000 rpm. The shear stress must not exceed 40 MPa and the twist must not exceed 0.75° per m of length. Find the smallest diameter d that satisfies both limits.
A point has σₓ = 20 MPa, σᵧ = 0 MPa and τₓᵧ = 60 MPa (tension positive). The element is rotated 50° counter-clockwise. Find the normal stress σy′ on the faces of the rotated element that are perpendicular to the rotated y′-axis.
A point in a loaded part has σₓ = −20 MPa, σᵧ = 20 MPa and τₓᵧ = 50 MPa (tension positive). Find the normal stress σθ on a plane whose normal is rotated 45° counter-clockwise from the x-axis.
Find the axial strain ε in the aluminium bar, in microstrain (µε = 10⁻⁶).
The stepped bar is fixed at the wall and loaded at its free end. Find the total elongation δ.
A column of length L made of steel is fixed at both ends. Using Euler’s formula, find its critical buckling load Pcr.
A solid round column of length L made of aluminium is fixed at the base and free at the top. It must carry 115 kN with a factor of safety of 2.5 against buckling. Find the smallest diameter d.
In a free-vibration test of a damped mass–spring system, a displacement peak of 15 mm is followed 2 cycles later by a peak of 10.3 mm. Find the damping ratio ζ.
A 25 kg mass hangs from two springs connected end to end (in series): the upper spring has k₁ = 30 kN/m and the lower one k₂ = 12 kN/m. Ignore damping and the masses of the springs. Find the natural frequency fn of vertical vibration in Hz.
Answer: n2 = 864 rpm
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: P = 7.073 kW
Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.
Answer: G = 80.02 GPa
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Compare: steel ≈ 80 GPa, brass ≈ 39 GPa, aluminium ≈ 26 GPa.
Answer: d = 36.92 mm
Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.
Both limits must hold, so the larger diameter governs.
Here stiffness governs.
Answer: σy′ = −47.35 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
The sum of the normal stresses does not change with rotation.
Answer: σθ = 50 MPa
Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.
Answer: ε = 505.3 µε
Hooke’s law: within the elastic range σ = E·ε. Combining with σ = P/A and ε = δ/L gives δ = PL/(AE).
E for aluminium = 70 GPa = 70000 MPa.
Answer: δ = 3.145 mm
Axially loaded members: each prismatic segment obeys δ = PL/(AE). For members in series the elongations add.
The free end carries P, so every section of the bar carries the same axial force P. Only the areas and materials change.
Answer: Pcr = 15.5 kN
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
A round section has the same I about every axis.
Answer: d = 107.9 mm
Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.
Check: the slenderness KL/r is 148.3, so the column is slender and Euler applies.
Answer: ζ = 0.0299
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Answer: fn = 2.947 Hz
Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.
Springs in series share the same force and add their deflections, so they combine as reciprocals: 1/k = 1/k1 + 1/k2.
ExamProblems · examproblems.com/courses/machine-design