Machine Design: cram pack

Formula sheets, the key method steps for every topic and 12 practice problems, with full solutions at the back.

New problemsBack to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Gears & gear trains

Meshing gears
n1·N1 = n2·N2
Torque
T2 = T1·(N2/N1)·η
Power
P = T·ω, ω = 2π·n/60
Compound train
total ratio = product of the stage ratios

Torsion of shafts

Shear stress
τ = T·r/J
Solid shaft
J = πd⁴/32
Hollow shaft
J = π(D⁴ − d⁴)/32
Angle of twist
φ = TL/(GJ)
Power
P = T·ω = 2πnT/60

Method

  1. Find the polar moment of area: J = πd⁴/32 for a solid shaft.
  2. Shear stress at the surface: τ = T·r/J, with r the outer radius.
  3. Angle of twist: φ = TL/(GJ) in radians.
  4. If power is given, find the torque first with P = T·ω, ω = 2πn/60.

Mohr’s circle & stress transformation

Centre
C = (σx + σy)/2
Radius
R = √(((σx − σy)/2)² + τxy²)
Principal stresses
σ1,2 = C ± R
Principal direction
tan 2θp = 2τxy/(σx − σy)
Inclined plane
σθ = C + (σx − σy)/2·cos 2θ + τxy·sin 2θ

Method

  1. Calculate the centre of Mohr’s circle: C = (σx + σy)/2.
  2. Calculate the radius: R = √(((σx − σy)/2)² + τxy²).
  3. The principal stresses are C ± R and the largest in-plane shear stress is R.
  4. Angles on the circle are double the angles on the element: tan 2θp = 2τxy/(σx − σy).

Axial stress & strain

Normal stress
σ = F/A
Strain
ε = ΔL/L
Hooke’s law
σ = E·ε
Elongation
ΔL = FL/(EA)
Thermal strain
εT = α·ΔT

Column buckling

Euler load
Pcr = π²EI/(KL)²
Effective length factor
K = 1 pinned–pinned, 0.5 fixed–fixed, 0.7 fixed–pinned, 2 fixed–free
Critical stress
σcr = Pcr/A
Slenderness
λ = KL/r, r = √(I/A)

Mechanical vibrations

Natural frequency
ωn = √(k/m), fn = ωn/(2π)
From static deflection
ωn = √(g/δst)
Critical damping
cc = 2√(km) = 2mωn
Damping ratio
ζ = c/cc
Damped frequency
ωd = ωn√(1 − ζ²)
Logarithmic decrement
δ = (1/n)·ln(x0/xn), ζ = δ/√(4π² + δ²)
Springs in parallel
k = k1 + k2
Springs in series
1/k = 1/k1 + 1/k2

2Practice problems

1.Gears & gear trainsMedium
d1​ = 150 mmd2​ = 400 mm2880 rpmT1​ = 1500 NT2​ = 600 NP = ?

A belt runs on a 150 mm driving pulley at 2880 rpm. The tension is 1500 N on the tight side and 600 N on the slack side. Find the power P transmitted, in kW.

d1 = 150 mmn1 = 2880 rpmT1 = 1500 NT2 = 600 N
P = kW
2.Gears & gear trainsHard
Ns​ = 12nr​ = ?Np​ = 18carrier fixed

In a planetary gear set the sun gear has 12 teeth and each planet gear has 18 teeth. The planet carrier is held fixed and the sun is driven at 3000 rpm. Find the speed nr of the ring gear (magnitude).

Ns = 12Np = 18ns = 3000 rpm
nr = rpm
3.Torsion of shaftsMedium
T = 200 N·md = 20 mmL = 0.5 mφ = ?

A solid steel shaft is fixed at the wall and twisted by a torque T at its free end. Find the angle of twist φ of the free end, in degrees.

T = 200 N·md = 20 mmL = 0.5 mG = 80 GPa
φ = °
4.Torsion of shaftsHard
d = 30 mmTB​ = 250 N·mTC​ = 200 N·mABC0.5 m1.5 m

A solid aluminium shaft of diameter 30 mm is fixed at A. A torque of 250 N·m acts at B, 0.5 m from A, and a torque of 200 N·m in the same direction acts at the free end C, a further 1.5 m along. Find the maximum shear stress τmax in the shaft.

d = 30 mmTB = 250 N·mTC = 200 N·mAB = 0.5 mBC = 1.5 m
τmax = MPa
5.Mohr’s circle & stress transformationMedium
σx​ = 130σy​ = −10MPaτxy​ = ?

A point has σₓ = 130 MPa and σᵧ = −10 MPa. How large can the shear stress τxy (magnitude) become before the largest principal stress reaches 140 MPa?

σx = 130 MPaσy = −10 MPaσ1 = 140 MPa
τxy = MPa
6.Mohr’s circle & stress transformationHard
σy​ = −50τxy​ = 50MPa

A point in a thin plate is in plane stress: σₓ = 0 MPa, σᵧ = −50 MPa and τₓᵧ = 50 MPa (σz = 0). The material has a yield strength of 420 MPa. Find the factor of safety n against yielding by the von Mises (distortion energy) criterion.

σx = 0 MPaσy = −50 MPaτxy = 50 MPaσY = 420 MPa
n =
7.Axial stress & strainMedium
80 kNØ40100 GPaØ120/70500 mmδ = ?

A steel rod (diameter 40 mm, E = 200 GPa) sits inside a tube made of brass (outer diameter 120 mm, inner diameter 70 mm, E = 100 GPa). Both are 500 mm long and are compressed together between rigid plates by 80 kN. Find the shortening δ.

P = 80 kNrod: Ø40 mm, E = 200 GPatube: Ø120/Ø70 mm, E = 100 GPaL = 500 mm
δ = mm
8.Axial stress & strainHard
100 kN12400 mm400 mmØ30Ø60σ2​ = ?

A steel segment (diameter 30 mm, length 400 mm, E = 200 GPa) and a segment made of brass (diameter 60 mm, length 400 mm, E = 100 GPa) are joined end to end and fixed between two rigid walls. An axial load of 100 kN acts at the joint, towards segment 2. Find the magnitude of the stress σ2 in segment 2.

segment 1: steel, Ø30 mm, 400 mm, E = 200 GPasegment 2: brass, Ø60 mm, 400 mm, E = 100 GPaP = 100 kN
σ2 = MPa
9.Column bucklingMedium
PL = 2 md = 30 mmcross-section

A column of length L made of aluminium is pinned at both ends. Using Euler’s formula, find its critical buckling load Pcr.

L = 2 mE = 70 GPa (aluminium)d = 30 mm
Pcr = kN
10.Column bucklingHard
P = 145 kNL = 2.5 md = ?cross-section

A solid round column of length L made of aluminium is pinned at both ends. It must carry 145 kN with a factor of safety of 3 against buckling. Find the smallest diameter d.

P = 145 kNn = 3L = 2.5 mE = 70 GPa (aluminium)
d = mm
11.Mechanical vibrationsMedium
tx25 mm3 cycles8.1 mm

In a free-vibration test of a damped mass–spring system, a displacement peak of 25 mm is followed 3 cycles later by a peak of 8.1 mm. Find the damping ratio ζ.

x0 = 25 mmx3 = 8.1 mmn = 3
ζ =
12.Mechanical vibrationsHard
k1​ = 25k2​ = 30m = 5 kg

A 5 kg mass hangs from two springs side by side (in parallel), with stiffnesses k₁ = 25 kN/m and k₂ = 30 kN/m. The mass stays level. Find the equivalent stiffness keq of the spring system in kN/m.

m = 5 kgk1 = 25 kN/mk2 = 30 kN/m
keq = kN/m

3Solutions

1.Gears & gear trains

Answer: P = 20.36 kW

Belt drives: without slip, both pulleys have the same rim speed v = π·d·n/60, so n₁·d₁ = n₂·d₂ and the speed ratio is d₂/d₁. Slip s makes the driven pulley a little slower: n₂ = n₁·(d₁/d₂)·(1 − s). The power transmitted is P = (T₁ − T₂)·v, with T₁ the tension on the tight side and T₂ on the slack side. Friction limits the ratio of the tensions: T₁/T₂ = eμθ, where θ is the angle of wrap in radians on the smaller pulley; for an open belt θ = π − 2·asin((d₂ − d₁)/(2C)) with centre distance C.

Belt speed

v = 22.62 m/s

Power

P = (1500 − 600)·22.62 = 20358 W = 20.36 kW

Answer

P = 20.36 kW
2.Gears & gear trains

Answer: nr = 750 rpm

Planetary gear sets: the speeds of sun, ring and carrier are linked by the Willis equation (ns − nc)/(nr − nc) = −Nr/Ns: seen from the carrier, the set is an ordinary train with the planets as idlers. Holding one member fixed turns the set into a single-ratio reducer.

Ring gear teeth

Nr = Ns + 2·Np = 12 + 2·18 = 48

Willis equation with the carrier fixed

With nc = 0 the sun drives the ring through the planets, which act as idlers.

nr = −ns·Ns/Nr = −3000·12/48 = −750 rpm
|nr| = 750 rpm

Answer

nr = 750 rpm

The ring turns opposite to the sun.

3.Torsion of shafts

Answer: φ = 4.559 °

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Polar second moment of area

J = π·20⁴/32 = 15708 mm⁴

Angle of twist

φ = TL/(GJ) = 200·1000·500/(80000·15708) = 0.07958 rad
φ = 0.07958·180/π = 4.559°

Answer

φ = 4.559°
4.Torsion of shafts

Answer: τmax = 84.88 MPa

Torsion of circular shafts: shear stress grows linearly from zero at the centre to τmax = T·r/J at the surface, with J = πd⁴/32 for a solid shaft and J = π(do⁴ − di⁴)/32 for a hollow one. The angle of twist is φ = TL/(GJ) in radians. Power and torque are linked by P = T·ω.

Internal torques

Sense of TC taken as positive.

TBC = TC = 200 N·m
TAB = TC + TB = 200 + 250 = 450 N·m

Maximum shear stress

The segment with the largest internal torque has the largest stress (same diameter).

|T|max = 450 N·m
τmax = 16·450000/(π·30³) = 84.88 MPa

Answer

τmax = 84.88 MPa
5.Mohr’s circle & stress transformation

Answer: τxy = 38.73 MPa

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R.

Required radius

C = (130 + (−10))/2 = 60 MPa
R = σ1 − C = 140 − 60 = 80 MPa
στxyCσ1​σ2​

Shear stress

τxy = √(R² − ((σₓ − σᵧ)/2)²) = √(80² − 70²) = 38.73 MPa

Answer

τxy = 38.73 MPa
6.Mohr’s circle & stress transformation

Answer: n = 4.2

Plane stress transformation: on a plane rotated by θ, σ = (σₓ + σᵧ)/2 + (σₓ − σᵧ)/2·cos 2θ + τₓᵧ·sin 2θ. Mohr’s circle shows all planes at once: its centre is at C = (σₓ + σᵧ)/2 and its radius is R = √(((σₓ − σᵧ)/2)² + τₓᵧ²). The principal stresses are C ± R, and the largest in-plane shear stress is R. Yield criteria: von Mises predicts yield when σvM = √(σ₁² − σ₁σ₂ + σ₂²) reaches σY; Tresca when the absolute maximum shear stress reaches σY/2.

στxyCσ1​σ2​

Principal stresses

C = −25 MPa, R = 55.9 MPa
σ1 = 30.9 MPa, σ2 = −80.9 MPa, σ3 = 0

Von Mises

σvM = √(30.9² − 30.9·(−80.9) + (−80.9)²) = 100 MPa
n = 420/100 = 4.2

Answer

n = 4.2

n > 1 means the point does not yield; Tresca is slightly more conservative than von Mises.

7.Axial stress & strain

Answer: δ = 0.0401 mm

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Areas

Ar = π·40²/4 = 1257 mm²
At = π(120² − 70²)/4 = 7461 mm²

Combined axial stiffness

ΣEA = 200·10³·1257 + 100·10³·7461 = 9.975 × 10⁸ N

Shortening

δ = 80000·500/9.975 × 10⁸ = 0.0401 mm

Answer

δ = 0.0401 mm
8.Axial stress & strain

Answer: σ2 = 23.58 MPa

Two materials: in series (one after the other) every segment carries the same force and the elongations add: δ = P·Σ L/(E·A). In parallel (side by side between rigid plates) both parts shorten by the same amount, so their strains are equal: the stiffer part takes the larger share, Pi = P·EiAi/ΣEA, and σi = Ei·ε. A bar held between two rigid walls with a load at the junction is statically indeterminate: the two segments share the load in proportion to their stiffness k = EA/L.

Stiffnesses

k₁ = 200000·706.9/400 = 353429 N/mm
k₂ = 100000·2827/400 = 706858 N/mm

Share of segment 2

F2 = 100000·706858/1.06 × 10⁶ = 66667 N

Stress

σ2 = 66667/2827 = 23.58 MPa (compression)

Answer

σ2 = 23.58 MPa
9.Column buckling

Answer: Pcr = 6.867 kN

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Smallest second moment of area

A round section has the same I about every axis.

I = πd⁴/64 = π·30⁴/64 = 39761 mm⁴

Effective length

KL = 1·2000 = 2000 mm

Critical load

Pcr = π²EI/(KL)² = π²·70000·39761/2000² = 6867 N = 6.867 kN

Answer

Pcr = 6.867 kN
10.Column buckling

Answer: d = 94.62 mm

Euler buckling: a slender column becomes unstable at Pcr = π²EI/(KL)², where KL is the effective length: K = 1 for pinned–pinned, 2 for fixed–free, 0.7 for fixed–pinned and 0.5 for fixed–fixed. It buckles about the axis with the smallest I. The formula holds for slender columns, whose critical stress stays below the yield stress.

Required critical load

Pcr = n·P = 3·145000 = 435000 N
KL = 1·2500 = 2500 mm

Solve for the diameter

d = (64·n·P·(KL)²/(π³E))^(1/4) = (64·435000·2500²/(π³·70000))^(1/4) = 94.62 mm

Answer

d = 94.62 mm

Check: the slenderness KL/r is 105.7, so the column is slender and Euler applies.

11.Mechanical vibrations

Answer: ζ = 0.05968

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Logarithmic decrement

δ = (1/3)·ln(25/8.1) = 0.3757

Damping ratio

ζ = δ/√(4π² + δ²) = 0.3757/√(39.48 + 0.1411) = 0.05968

Answer

ζ = 0.05968
12.Mechanical vibrations

Answer: keq = 55 kN/m

Free vibration of a mass–spring system: the undamped natural frequency is ωn = √(k/m) in rad/s, and fn = ωn/(2π) in Hz. A viscous damper c gives the damping ratio ζ = c/cc, with critical damping cc = 2·√(k·m) = 2·m·ωn. An underdamped system (ζ < 1) oscillates at ωd = ωn·√(1 − ζ²). Springs in parallel add, k = k₁ + k₂; springs in series add as reciprocals, 1/k = 1/k₁ + 1/k₂.

Equivalent stiffness

Springs side by side share the deflection and add their forces, so their stiffnesses simply add: k = k1 + k2.

keq = 25 + 30 = 55 kN/m

Answer

keq = 55 kN/m

ExamProblems · examproblems.com/courses/machine-design