Formula sheets, the key method steps for every topic and 6 practice problems, with full solutions at the back.
Practice exercise (made-up values, not clinical guidance). A vial of penicillin G contains 5 000 000 units. Its practice label gives three strengths (see the table). You add 3.2 mL of diluent. The prescribed dose is 2 000 000 units. What volume V do you draw up? Round to one decimal place.
A vial holds 500 mg of powder. You add 2.3 mL of diluent, and the powder adds 0.2 mL of volume. The prescription is 240 mg. Draw up the dose: what volume V do you give?
A child weighing 6 kg is prescribed 7.5 mg/kg of a drug. The stock solution contains 25 mg/mL. Draw up the dose: what volume V do you give?
An infusion contains 40000 units of a drug in 250 mL. The prescription is 1500 units per hour. At what rate R do you set the pump, in mL/h?
Practice exercise (made-up values, not clinical guidance). A patient receives an IV bolus of 250 mg of gentamicin. The level back-extrapolated to time zero is 10 mg/L and the half-life is 3 h. Find the clearance CL in L/h.
Practice exercise (made-up values, not clinical guidance). A 57 kg patient takes oral theophylline (F = 1) every 8 h. The clearance is 0.04 L/kg/h. What dose D in mg gives an average steady-state level of 15 mg/L?
Answer: V = 2 mL
Reconstitution: the powder takes up space, so the final volume is the diluent plus the powder volume. Concentration = drug in the vial/final volume, and the volume to give = dose/concentration. On a multi-strength label, use the concentration that belongs to the amount of diluent you actually added. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: V = 1.2 mL
Strength to volume: turn the strength into mg per mL first. A w/v percentage is grams per 100 mL, so x% = 10x mg/mL. A ratio strength 1:n is 1 g in n mL. After reconstitution the concentration is the powder's dose over the final volume (diluent + powder volume). Then volume = dose/concentration.
Answer: V = 1.8 mL
Drawing up a dose: volume = (prescribed dose/stock strength) × stock volume. Convert to the same units first, then check that the volume fits the syringe and lands on one of its graduations.
On this 10 mL syringe every small line is 0.2 mL.
Answer: R = 9.375 mL/h
Dose calculation: the amount to give equals what is prescribed divided by what you have, times the quantity it comes in: amount = (desired dose/stock strength) × stock volume. Always keep the units the same (convert g to mg, mg to mcg first) and check that the answer is sensible.
Answer: CL = 5.776 L/h
Clearance and volume: at steady state the dosing rate equals the elimination rate, so the maintenance rate = CL × Css. A loading dose is LD = Vd × C/(S × F), with S the salt factor (fraction of active drug in the salt) and F the bioavailability (1 for IV). From two levels, k = ln(C₁/C₂)/Δt; for an IV bolus Vd = dose/C₀ and CL = k × Vd. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
Answer: D = 273.6 mg
Designing a regimen: with rapid IV doses the level falls from peak to trough during the interval, so τ = ln(Cpeak/Ctrough)/k and the dose that restores the peak is Vd × (Cpeak − Ctrough). The average steady-state level is Css,avg = S·F·dose/(CL·τ). An infusion rises as C = (R/CL)(1 − e−kt). For a drug cleared by the kidneys, the dose is scaled with the creatinine clearance. The numbers are for practice only; at the bedside always follow local protocols and have high-risk doses double-checked.
ExamProblems · examproblems.com/courses/pharmacy-calculations