Physics 2: Electricity and Magnetism: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problems Back to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Coulomb’s law & electric fields

Coulomb’s law: F = k·|q₁q₂|/r²
Field of a point charge: E = k·|q|/r²
Constant: k = 8.99 × 10⁹ N·m²/C²
Force on a charge: F = q·E

Series & parallel resistors

Resistors in series: R_eq = R₁ + R₂ + …
Resistors in parallel: 1/R_eq = 1/R₁ + 1/R₂ + …
Two in parallel: R_eq = R₁R₂ / (R₁ + R₂)
Ohm's law: V = I·R
Power: P = V·I = I²R = V²/R

Method

Start at the end of the network furthest from the terminals.
Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
Redraw the circuit after each step.
Repeat until one resistor is left between the terminals.

RC & RL transients

Time constant: τ = RC | τ = L/R
Response: x(t) = x(∞) + [x(0) − x(∞)]·e^−t/τ
Capacitor at DC: open circuit; v_C cannot jump
Inductor at DC: short circuit; i_L cannot jump
Settled: t ≈ 5τ

Method

Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
Use x(t) = x(∞) + [x(0) − x(∞)]·e^−t/τ.

Magnetic fields & induction

Long straight wire: B = μ₀I/(2πr)
Centre of a flat coil: B = μ₀NI/(2R)
Long solenoid: B = μ₀nI, n = N/L
Constant: μ₀ = 4π × 10⁻⁷ T·m/A
Force on a wire: F = BIL·sin θ
Force on a charge: F = |q|vB·sin θ
Circular motion: r = mv/(|q|B), T = 2πm/(|q|B)
Parallel wires: F/L = μ₀I₁I₂/(2πd)
Flux: Φ = BA·cos θ
Faraday’s law: ε = −N·ΔΦ/Δt
Moving rod: ε = BLv
Generator: E₀ = NBAω, E_rms = E₀/√2
Inductance: ε = L·ΔI/Δt, L = μ₀N²A/l, W = ½LI²
Mutual inductance: ε₂ = M·di₁/dt, M = k√(L₁L₂)
Velocity selector and spectrometer: v = E/B, r = √(2mV/|q|)/B

Method

Convert every quantity to SI units: cm to m, cm² to m², mT and µT to T.
Pick the right formula: B = μ₀I/(2πr) for a wire, μ₀NI/(2R) for the centre of a coil, μ₀nI inside a solenoid; F = BIL·sin θ or |q|vB·sin θ for forces.
For induction, find the change of flux ΔΦ = Δ(BA·cos θ) and use ε = N·ΔΦ/Δt, or ε = BLv for a moving rod and NBAω for a rotating coil.
Find directions separately with the right-hand rules, and Lenz’s law for induced currents.

AC impedance & phasors

Impedances: Z_R = R, Z_L = jωL, Z_C = 1/(jωC)
Angular frequency: ω = 2πf
Magnitude and angle: |Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law: V = I·Z

Method

Convert the frequency: ω = 2πf.
Find each reactance: X_L = ωL and X_C = 1/(ωC).
Add impedances like resistors, with Z = R + jX.
Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

2Practice problems

1.Coulomb’s law & electric fieldsMedium

A charge of +4 µC and a charge of +1 µC are 30 cm apart. Point P lies on the line between them, 12 cm from the first charge. Find the magnitude of the electric field E at P.

q₁ = +4 µCq₂ = +1 µCr₁ = 12 cmr₂ = 18 cm

E = N/C

2.Coulomb’s law & electric fieldsHard

Two identical small balls, each of mass 3 g, hang from the same point on insulating threads 40 cm long. They are given equal charges and each thread settles at 10° from the vertical. Use g = 9.81 m/s². Find the charge q on each ball in nC. Use k = 8.99 × 10⁹ N·m²/C².

m = 3 gL = 40 cmθ = 10°g = 9.81 m/s²

q = nC

3.Series & parallel resistorsMedium

Find the current I_R1 delivered by the source, which flows through R₁.

V₁ = 6 VR₁ = 20 ΩR₂ = 2 ΩR₃ = 12 ΩR₄ = 2 Ω

I_R1 = A

4.Series & parallel resistorsHard

Find the equivalent resistance R_eq seen by the source V₁.

V₁ = 5 VR₁ = 4 ΩR₂ = 5 ΩR₃ = 4 ΩR₄ = 30 ΩR₅ = 5 ΩR₆ = 3 Ω

R_eq = Ω

5.RC & RL transientsMedium

The inductor carries a steady current of 1 A. At t = 0 the switch closes the loop through R and the source is removed, so the inductor current decays through R. Find the voltage v_R across R at t = 5 ms.

i(0) = 1 AR = 10 ΩL = 100 mHt = 5 ms

v_R = V

6.RC & RL transientsHard

The switch across R₂ has been closed for a long time, so the inductor current is steady. At t = 0 the switch opens. Find the inductor current i at t = 1 ms.

V_s = 10 VR₁ = 47 ΩR₂ = 33 ΩL = 33 mHt = 1 ms

i = A

7.Magnetic fields & inductionMedium

A coil of 50 turns, area 100 cm² and resistance 4 Ω forms a closed circuit. A uniform field perpendicular to the coil rises steadily from 0.2 T to 0.3 T in 200 ms. Find the average induced current I.

N = 50A = 100 cm²B: 0.2 T → 0.3 TΔt = 200 msR = 4 Ω

I = mA

8.Magnetic fields & inductionHard

A long air-core solenoid has 2000 turns, a length of 25 cm and a diameter of 5 cm. Find the energy W stored in its magnetic field when it carries 1 A.

N = 2000l = 25 cm⌀ = 5 cmI = 1 Aμ₀ = 4π × 10⁻⁷ T·m/A

W = mJ

9.AC impedance & phasorsMedium

A series RLC circuit with L = 200 mH must resonate at 100 Hz. Find the capacitance C needed.

f₀ = 100 HzL = 200 mH

C = µF

10.AC impedance & phasorsHard

A series RLC circuit is connected to a 100 V (rms), 1000 Hz supply. Find the resonant frequency f₀ of the circuit.

V = 100 V (rms)f = 1000 HzR = 80 ΩL = 50 mHC = 4.7 µF

f₀ = Hz

3Solutions

1.Coulomb’s law & electric fields

Answer: E = 2.22 × 10⁶ N/C

Coulomb’s law: two point charges attract or repel with F = k·|q₁·q₂|/r², with k = 8.99 × 10⁹ N·m²/C². The field of a point charge is E = k·|q|/r², pointing away from a positive charge and towards a negative one. Forces and fields from several charges add as vectors.

Field of each charge

E₁ = k·4 × 10⁻⁶/0.12² = 2.497 × 10⁶ N/C

E₂ = k·1 × 10⁻⁶/0.18² = 277469 N/C

Directions and sum

Both charges are positive: at P their fields point away from each charge, so in opposite directions.

E = |2.497 × 10⁶ − 277469| = 2.22 × 10⁶ N/C

Answer

E = 2.22 × 10⁶ N/C

2.Coulomb’s law & electric fields

Answer: q = 105.5 nC

Electric force from the equilibrium

The tension's horizontal part balances F, its vertical part balances m·g.

F = m·g·tan θ = 0.003·9.81·tan 10° = 0.005189 N

Separation

r = 2·L·sin θ = 2·0.4·sin 10° = 0.1389 m

Charge

F = k·q²/r² → q = r·√(F/k) = 0.1389·√(0.005189/8.99 × 10⁹) = 1.055 × 10⁻⁷ C = 105.5 nC

Answer

q = 105.5 nC

3.Series & parallel resistors

Answer: I_R1 = 0.2759 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R₃ + R₄ = 12 + 2 = 14 Ω

R₂ ∥ 14 = 2·14/(2+14) = 1.75 Ω

R_eq = R₁ + 1.75 = 20 + 1.75 = 21.75 Ω

Current from the source

The source sees only R_eq, so Ohm’s law gives the current it delivers. That current flows through R₁.

I_R1 = V₁/R_eq = 6/21.75 = 0.2759 A

Answer

I_R1 = 0.2759 A

4.Series & parallel resistors

Answer: R_eq = 7.368 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R₅ + R₆ = 5 + 3 = 8 Ω

R₄ ∥ 8 = 6.316 Ω

R₃ + 6.316 = 10.32 Ω

R₂ ∥ 10.32 = 3.368 Ω

R_eq = R₁ + 3.368 = 4 + 3.368 = 7.368 Ω

Answer

R_eq = 7.368 Ω

5.RC & RL transients

Answer: v_R = 6.065 V

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e^−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Time constant

τ = L/R = 100 mH / 10 Ω = 10 ms

Decay of the current

i(t) = 1·e^−5/10 = 0.6065 A

v_R = R·i = 10·0.6065 = 6.065 V

Answer

v_R = 6.065 V

6.RC & RL transients

Answer: i = 0.1328 A

Initial value, final value, time constant

Before t = 0 the closed switch bypasses R₂; afterwards R₁ and R₂ are both in the loop.

i(0) = 10/47 = 0.2128 A

i(∞) = 10/(47 + 33) = 0.125 A

τ = L/R = 33/80 = 0.4125 ms

i(t) = 0.125 + (0.2128 − 0.125)·e^−t/τ

Current at the given time

i(1) = 0.125 + (0.08777)·e^−1/0.4125 = 0.1328 A

Answer

i = 0.1328 A

7.Magnetic fields & induction

Answer: I = 62.5 mA

Electromagnetic induction: the flux through a loop is Φ = BA·cos θ, with θ between B and the normal of the loop. Faraday's law: a change of flux induces emf = −N·dΦ/dt in a coil of N turns, and Lenz's law says the induced current flows so that its own field opposes the change. A rod moving across a field gives emf = BLv. A coil rotating at ω gives e = NBAω·sin ωt, peak NBAω. Self-inductance: emf = −L·di/dt, with L = μ₀N²A/l for a long solenoid, and the energy stored is W = ½LI². Two coupled coils: emf₂ = −M·di₁/dt with M = k√(L₁L₂).

Change of flux per turn

ΔΦ = (0.3 − 0.2)·0.01 = 0.001 Wb

Average emf

ε = NΔΦ/Δt = 50·0.001/0.2 = 0.25 V

Current

I = ε/R = 0.25/4 = 0.0625 A

Answer

I = 62.5 mA

8.Magnetic fields & induction

Answer: W = 19.74 mJ

Self-inductance

L = μ₀N²A/l = 39.48 mH

Stored energy

W = ½LI² = ½·0.03948·1² = 0.01974 J = 19.74 mJ

Answer

W = 19.74 mJ

9.AC impedance & phasors

Answer: C = 12.67 µF

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Resonance condition

At resonance the inductive and capacitive reactances cancel: ωL = 1/(ωC).

ω₀ = 2π·100 = 628.3 rad/s

C = 1/(ω₀²·L) = 1/(628.3²·0.2) = 12.67 µF

Answer

C = 12.67 µF

10.AC impedance & phasors

Answer: f₀ = 328.3 Hz

Resonance

At resonance the inductive and capacitive reactances cancel: ωL = 1/(ωC). The supply frequency does not matter.

f₀ = 1/(2π√(LC)) = 1/(2π·√(0.05·4.7·10⁻⁶)) = 328.3 Hz

Answer

f₀ = 328.3 Hz

ExamProblems · examproblems.com/courses/physics-2-electricity-and-magnetism