Coulomb’s law & electric fields
- Coulomb’s law
- F = k·|q1q2|/r²
- Field of a point charge
- E = k·|q|/r²
- Constant
- k = 8.99 × 10⁹ N·m²/C²
- Force on a charge
- F = q·E
Physics 2: Electricity and Magnetism: cram pack
Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.
1Formulas and methods
Series & parallel resistors
- Resistors in series
- Req = R1 + R2 + …
- Resistors in parallel
- 1/Req = 1/R1 + 1/R2 + …
- Two in parallel
- Req = R1R2 / (R1 + R2)
- Ohm's law
- V = I·R
- Power
- P = V·I = I²R = V²/R
Method
- Start at the end of the network furthest from the terminals.
- Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
- Redraw the circuit after each step.
- Repeat until one resistor is left between the terminals.
RC & RL transients
- Time constant
- τ = RC | τ = L/R
- Response
- x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ
- Capacitor at DC
- open circuit; vC cannot jump
- Inductor at DC
- short circuit; iL cannot jump
- Settled
- t ≈ 5τ
Method
- Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
- Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
- Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
- Use x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ.
Magnetic fields & induction
- Long straight wire
- B = μ0I/(2πr)
- Centre of a flat coil
- B = μ0NI/(2R)
- Long solenoid
- B = μ0nI, n = N/L
- Constant
- μ0 = 4π × 10⁻⁷ T·m/A
- Force on a wire
- F = BIL·sin θ
- Force on a charge
- F = |q|vB·sin θ
- Circular motion
- r = mv/(|q|B), T = 2πm/(|q|B)
- Parallel wires
- F/L = μ0I1I2/(2πd)
- Flux
- Φ = BA·cos θ
- Faraday’s law
- ε = −N·ΔΦ/Δt
- Moving rod
- ε = BLv
- Generator
- E0 = NBAω, Erms = E0/√2
- Inductance
- ε = L·ΔI/Δt, L = μ0N²A/l, W = ½LI²
- Mutual inductance
- ε2 = M·di1/dt, M = k√(L1L2)
- Velocity selector and spectrometer
- v = E/B, r = √(2mV/|q|)/B
Method
- Convert every quantity to SI units: cm to m, cm² to m², mT and µT to T.
- Pick the right formula: B = μ₀I/(2πr) for a wire, μ₀NI/(2R) for the centre of a coil, μ₀nI inside a solenoid; F = BIL·sin θ or |q|vB·sin θ for forces.
- For induction, find the change of flux ΔΦ = Δ(BA·cos θ) and use ε = N·ΔΦ/Δt, or ε = BLv for a moving rod and NBAω for a rotating coil.
- Find directions separately with the right-hand rules, and Lenz’s law for induced currents.
AC impedance & phasors
- Impedances
- ZR = R, ZL = jωL, ZC = 1/(jωC)
- Angular frequency
- ω = 2πf
- Magnitude and angle
- |Z| = √(R² + X²), φ = atan(X/R)
- Phasor Ohm’s law
- V = I·Z
Method
- Convert the frequency: ω = 2πf.
- Find each reactance: XL = ωL and XC = 1/(ωC).
- Add impedances like resistors, with Z = R + jX.
- Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.
2Practice problems
1.Coulomb’s law & electric fieldsMedium
Three point charges lie on a straight line: +1 µC on the left, +4 µC on the right 30 cm away, and +5 µC between them, 18 cm from the left charge. Find the magnitude of the net electric force F on the middle charge. Use k = 8.99 × 10⁹ N·m²/C².
qL = +1 µCqR = +4 µCqM = +5 µCrL = 18 cmrR = 12 cm
F = N
2.Coulomb’s law & electric fieldsHard
Three positive point charges sit at the corners of a right triangle: q₃ = 3 µC is at the right-angle corner, q₁ = 3 µC is 8 cm from it along one side and q₂ = 2 µC is 10 cm from it along the other side. Find the magnitude of the net electric force F on q₃.
q1 = 3 µCq2 = 2 µCq3 = 3 µCr13 = 8 cmr23 = 10 cm
F = N
3.Series & parallel resistorsMedium
Find the equivalent resistance Req seen by the source V1.
V1 = 15 VR1 = 10 ΩR2 = 15 ΩR3 = 10 ΩR4 = 10 Ω
Req = Ω
4.Series & parallel resistorsHard
Find the equivalent resistance Req seen by the source V1.
V1 = 36 VR1 = 30 ΩR2 = 30 ΩR3 = 2 ΩR4 = 6 ΩR5 = 12 ΩR6 = 25 Ω
Req = Ω
5.RC & RL transientsMedium
The inductor carries no current before the switch closes at t = 0. How long after the switch closes does the current reach 50% of its final value? Find t.
Vs = 12 VR = 20 ΩL = 22 mH
t = ms
6.RC & RL transientsHard
The switch has been closed for a long time, so the circuit is in steady state. At t = 0 the switch opens. Find the capacitor voltage vC at t = 500 ms.
Vs = 10 VR1 = 3.3 kΩR2 = 4.7 kΩC = 220 µFt = 500 ms
vC = V
7.Magnetic fields & inductionMedium
A wire carries a current down the page through a uniform magnetic field pointing out of the page. Click the direction of the magnetic force on the wire.
I: down the pageB: out of the page
- 1up the page
- 2to the right
- 3down the page
- 4to the left
8.Magnetic fields & inductionHard
A coil of 250 turns, 10 cm × 5 cm, rotates in a uniform field of 0.3 T about an axis perpendicular to the field. At what speed n (in revolutions per minute) must it turn to give an rms emf of 83.3 V?
N = 250A = 10 cm × 5 cmB = 0.3 TErms = 83.3 V
n = rpm
9.AC impedance & phasorsMedium
A series RLC circuit is connected to a 12 V (rms), 500 Hz supply. Find the phase angle φ of the impedance, in degrees (positive when the current lags the voltage).
V = 12 V (rms)f = 500 HzR = 50 ΩL = 250 mHC = 4.7 µF
φ = °
10.AC impedance & phasorsHard
A series RLC circuit has R = 50 Ω, L = 50 mH and C = 0.047 µF. Find its quality factor Q at resonance.
R = 50 ΩL = 50 mHC = 0.047 µF
Q =
3Solutions
1.Coulomb’s law & electric fields
Answer: F = 11.1 N
Coulomb’s law: two point charges attract or repel with F = k·|q₁·q₂|/r², with k = 8.99 × 10⁹ N·m²/C². The field of a point charge is E = k·|q|/r², pointing away from a positive charge and towards a negative one. Forces and fields from several charges add as vectors.
Force from each charge
Right is positive.
FL = +k·1·5 × 10⁻¹²/0.18² = 1.387 N
FR = −k·4·5 × 10⁻¹²/0.12² = −12.49 N
Net force
F = 1.387 + (−12.49) = −11.1 N → |F| = 11.1 N
Answer
F = 11.1 N
The net force points to the left.
2.Coulomb’s law & electric fields
Answer: F = 13.74 N
Coulomb’s law: two point charges attract or repel with F = k·|q₁·q₂|/r², with k = 8.99 × 10⁹ N·m²/C². The field of a point charge is E = k·|q|/r², pointing away from a positive charge and towards a negative one. Forces and fields from several charges add as vectors.
Each force on q₃
F1 = k·3·3 × 10⁻¹²/0.08² = 12.64 N
F2 = k·2·3 × 10⁻¹²/0.1² = 5.394 N
Vector sum
F = √(12.64² + 5.394²) = 13.74 N
Answer
F = 13.74 N
3.Series & parallel resistors
Answer: Req = 18.57 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R3 + R4 = 10 + 10 = 20 Ω
R2 ∥ 20 = 15·20/(15+20) = 8.571 Ω
Req = R1 + 8.571 = 10 + 8.571 = 18.57 Ω
Answer
Req = 18.57 Ω
4.Series & parallel resistors
Answer: Req = 35.78 Ω
Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.
Combine resistors from the far end
Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.
R5 + R6 = 12 + 25 = 37 Ω
R4 ∥ 37 = 5.163 Ω
R3 + 5.163 = 7.163 Ω
R2 ∥ 7.163 = 5.782 Ω
Req = R1 + 5.782 = 30 + 5.782 = 35.78 Ω
Answer
Req = 35.78 Ω
5.RC & RL transients
Answer: t = 0.7625 ms
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Time constant and final current
Long after the switch closes the inductor behaves like a short circuit, so the final current is set by R alone.
τ = L/R = 22 mH / 20 Ω = 1.1 ms
i(∞) = Vs/R = 12/20 = 0.6 A
Solve for the time
0.5 = 1 − e−t/τ → t = −τ·ln(1 − 0.5)
t = −1.1·ln(0.5) = 0.7625 ms
Answer
t = 0.7625 ms
6.RC & RL transients
Answer: vC = 3.622 V
First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.
Initial capacitor voltage
In steady state the capacitor is an open circuit, so R₁ and R₂ form a voltage divider. The capacitor voltage cannot jump when the switch opens.
vC(0) = 10·4.7/(3.3 + 4.7) = 5.875 V
Time constant after the switch opens
τ = R2·C = 4.7·220 = 1034 ms
Discharge
vC(t) = 5.875·e−500/1034 = 3.622 V
Answer
vC = 3.622 V
7.Magnetic fields & induction
Answer: to the left
Magnetic forces: a straight wire carrying I in a field B feels F = BIL·sin θ, and a moving charge F = |q|vB·sin θ, where θ is the angle between the current (or velocity) and B. The force is perpendicular to both: point the fingers of the right hand along I or v, curl them towards B, and the thumb gives F for a positive charge; reverse it for a negative charge. Because F is perpendicular to v, a charge moving across a uniform field moves on a circle: |q|vB = mv²/r gives r = mv/(|q|B) and the period T = 2πm/(|q|B), which does not depend on the speed. Two parallel wires attract for currents in the same direction: F/L = μ₀I₁I₂/(2πd).
Right-hand rule
Point the fingers along the current or velocity and curl them towards B; the thumb gives the force on a positive charge.
I: down the page, B: out of the page
Direction of the force
to the left
Answer
F: to the left
8.Magnetic fields & induction
Answer: n = 3000 rpm
Electromagnetic induction: the flux through a loop is Φ = BA·cos θ, with θ between B and the normal of the loop. Faraday's law: a change of flux induces emf = −N·dΦ/dt in a coil of N turns, and Lenz's law says the induced current flows so that its own field opposes the change. A rod moving across a field gives emf = BLv. A coil rotating at ω gives e = NBAω·sin ωt, peak NBAω. Self-inductance: emf = −L·di/dt, with L = μ₀N²A/l for a long solenoid, and the energy stored is W = ½LI². Two coupled coils: emf₂ = −M·di₁/dt with M = k√(L₁L₂).
Peak emf
E₀ = √2·Erms = 117.8 V
Angular speed
ω = E₀/(NBA) = 117.8/(250·0.3·0.005) = 314.1 rad/s
Revolutions per minute
n = 60·314.1/(2π) = 3000 rpm
Answer
n = 3000 rpm
9.AC impedance & phasors
Answer: φ = 86.01 °
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
Reactances
ω = 2πf = 2π·500 = 3142 rad/s
XL = ωL = 3142·0.25 = 785.4 Ω
XC = 1/(ωC) = 1/(3142·4.7·10⁻⁶) = 67.73 Ω
Impedance
In series the impedances add as complex numbers: Z = R + j(XL − XC).
|Z| = √(R² + (XL − XC)²) = √(50² + (717.7)²) = 719.4 Ω
Phase angle
φ = arctan((XL − XC)/R) = arctan(717.7/50) = 86.01°
Answer
φ = 86.01°
10.AC impedance & phasors
Answer: Q = 20.63
AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.
Resonant frequency
f0 = 1/(2π·√(0.05·0.047·10⁻⁶)) = 3283 Hz
Quality factor
Q compares the reactance at resonance with the resistance: Q = ω₀L/R.
Q = (1/R)·√(L/C) = (1/50)·√(0.05/(0.047·10⁻⁶)) = 20.63
Answer
Q = 20.63
ExamProblems · examproblems.com/courses/physics-2-electricity-and-magnetism