Physics 2: Electricity and Magnetism: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problems Back to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Coulomb’s law & electric fields

Coulomb’s law: F = k·|q₁q₂|/r²
Field of a point charge: E = k·|q|/r²
Constant: k = 8.99 × 10⁹ N·m²/C²
Force on a charge: F = q·E

Series & parallel resistors

Resistors in series: R_eq = R₁ + R₂ + …
Resistors in parallel: 1/R_eq = 1/R₁ + 1/R₂ + …
Two in parallel: R_eq = R₁R₂ / (R₁ + R₂)
Ohm's law: V = I·R
Power: P = V·I = I²R = V²/R

Method

Start at the end of the network furthest from the terminals.
Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
Redraw the circuit after each step.
Repeat until one resistor is left between the terminals.

RC & RL transients

Time constant: τ = RC | τ = L/R
Response: x(t) = x(∞) + [x(0) − x(∞)]·e^−t/τ
Capacitor at DC: open circuit; v_C cannot jump
Inductor at DC: short circuit; i_L cannot jump
Settled: t ≈ 5τ

Method

Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
Use x(t) = x(∞) + [x(0) − x(∞)]·e^−t/τ.

Magnetic fields & induction

Long straight wire: B = μ₀I/(2πr)
Centre of a flat coil: B = μ₀NI/(2R)
Long solenoid: B = μ₀nI, n = N/L
Constant: μ₀ = 4π × 10⁻⁷ T·m/A
Force on a wire: F = BIL·sin θ
Force on a charge: F = |q|vB·sin θ
Circular motion: r = mv/(|q|B), T = 2πm/(|q|B)
Parallel wires: F/L = μ₀I₁I₂/(2πd)
Flux: Φ = BA·cos θ
Faraday’s law: ε = −N·ΔΦ/Δt
Moving rod: ε = BLv
Generator: E₀ = NBAω, E_rms = E₀/√2
Inductance: ε = L·ΔI/Δt, L = μ₀N²A/l, W = ½LI²
Mutual inductance: ε₂ = M·di₁/dt, M = k√(L₁L₂)
Velocity selector and spectrometer: v = E/B, r = √(2mV/|q|)/B

Method

Convert every quantity to SI units: cm to m, cm² to m², mT and µT to T.
Pick the right formula: B = μ₀I/(2πr) for a wire, μ₀NI/(2R) for the centre of a coil, μ₀nI inside a solenoid; F = BIL·sin θ or |q|vB·sin θ for forces.
For induction, find the change of flux ΔΦ = Δ(BA·cos θ) and use ε = N·ΔΦ/Δt, or ε = BLv for a moving rod and NBAω for a rotating coil.
Find directions separately with the right-hand rules, and Lenz’s law for induced currents.

AC impedance & phasors

Impedances: Z_R = R, Z_L = jωL, Z_C = 1/(jωC)
Angular frequency: ω = 2πf
Magnitude and angle: |Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law: V = I·Z

Method

Convert the frequency: ω = 2πf.
Find each reactance: X_L = ωL and X_C = 1/(ωC).
Add impedances like resistors, with Z = R + jX.
Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

2Practice problems

1.Coulomb’s law & electric fieldsMedium

Charges of +10 µC and +5 µC are 30 cm apart. At what distance x from the +10 µC charge, on the line between them, is the electric field zero?

q₁ = +10 µCq₂ = +5 µCd = 30 cm

x = cm

2.Coulomb’s law & electric fieldsHard

Charges of +1 µC and +1 µC are 16 cm apart. Point P lies 8 cm from the midpoint between them, on the perpendicular bisector. Find the magnitude of the electric field E at P. Use k = 8.99 × 10⁹ N·m²/C².

q₁ = +1 µCq₂ = +1 µCd = 16 cmh = 8 cm

E = N/C

3.Series & parallel resistorsMedium

Find the current I_R1 delivered by the source, which flows through R₁.

V₁ = 6 VR₁ = 15 ΩR₂ = 2 ΩR₃ = 20 ΩR₄ = 2 Ω

I_R1 = A

4.Series & parallel resistorsHard

Find the current I_R1 delivered by the source, which flows through R₁.

V₁ = 24 VR₁ = 20 ΩR₂ = 10 ΩR₃ = 20 ΩR₄ = 10 ΩR₅ = 12 ΩR₆ = 2 Ω

I_R1 = A

5.RC & RL transientsMedium

The source Vₛ charges the capacitor through R₁, and R₂ is connected in parallel with C. The capacitor is uncharged when the switch closes at t = 0. Find the time constant τ of the circuit after the switch closes.

V_s = 24 VR₁ = 1 kΩR₂ = 2.2 kΩC = 33 µF

τ = ms

6.RC & RL transientsHard

The switch has been closed for a long time, so the circuit is in steady state. At t = 0 the switch opens. Find the capacitor voltage v_C at t = 250 ms.

V_s = 24 VR₁ = 3.3 kΩR₂ = 3.3 kΩC = 100 µFt = 250 ms

v_C = V

7.Magnetic fields & inductionMedium

Two long parallel wires 20 cm apart carry currents of 12 A and 30 A in opposite directions. Find the magnitude of the magnetic flux density B at point P, halfway between them.

I₁ = 12 AI₂ = 30 Ad = 20 cmμ₀ = 4π × 10⁻⁷ T·m/A

B = µT

8.Magnetic fields & inductionHard

A coil of 20 turns, 8 cm × 20 cm, rotates at 1500 rpm in a uniform field of 0.1 T about an axis perpendicular to the field. Find the rms value E_rms of the emf.

N = 20A = 8 cm × 20 cmB = 0.1 Tn = 1500 rpm

E_rms = V

9.AC impedance & phasorsMedium

A series RLC circuit is connected to a 24 V (rms), 60 Hz supply. Find the real power P taken from the supply.

V = 24 V (rms)f = 60 HzR = 15 ΩL = 250 mHC = 47 µF

P = W

10.AC impedance & phasorsHard

A series RLC circuit is driven by a 5 V (rms) source whose frequency is set to the resonant frequency of the circuit. Find the rms voltage V_L across the inductor.

V = 5 V (rms)R = 50 ΩL = 100 mHC = 0.22 µF

V_L = V

3Solutions

1.Coulomb’s law & electric fields

Answer: x = 17.57 cm

Coulomb’s law: two point charges attract or repel with F = k·|q₁·q₂|/r², with k = 8.99 × 10⁹ N·m²/C². The field of a point charge is E = k·|q|/r², pointing away from a positive charge and towards a negative one. Forces and fields from several charges add as vectors.

Equal fields

10/x² = 5/(30 − x)²

(30 − x)/x = √(5/10) = 0.7071

Position

x = 30/(1 + 0.7071) = 17.57 cm

Answer

x = 17.57 cm

The zero point is always closer to the smaller charge.

2.Coulomb’s law & electric fields

Answer: E = 993264 N/C

Distance and field of one charge

r = √(8² + 8²) = 11.31 cm

E₁ = k·1 × 10⁻⁶/0.1131² = 702344 N/C

Components

The components along the line joining the charges cancel.

E = 2·E₁·(h/r) = 2·702344·0.7071 = 993264 N/C

Answer

E = 993264 N/C

The field points along the bisector, away from the charges.

3.Series & parallel resistors

Answer: I_R1 = 0.3564 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R₃ + R₄ = 20 + 2 = 22 Ω

R₂ ∥ 22 = 2·22/(2+22) = 1.833 Ω

R_eq = R₁ + 1.833 = 15 + 1.833 = 16.83 Ω

Current from the source

The source sees only R_eq, so Ohm’s law gives the current it delivers. That current flows through R₁.

I_R1 = V₁/R_eq = 6/16.83 = 0.3564 A

Answer

I_R1 = 0.3564 A

4.Series & parallel resistors

Answer: I_R1 = 0.8821 A

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R₅ + R₆ = 12 + 2 = 14 Ω

R₄ ∥ 14 = 5.833 Ω

R₃ + 5.833 = 25.83 Ω

R₂ ∥ 25.83 = 7.209 Ω

R_eq = R₁ + 7.209 = 20 + 7.209 = 27.21 Ω

Current from the source

The source sees only R_eq, so Ohm’s law gives the current it delivers. That current flows through R₁.

I_R1 = V₁/R_eq = 24/27.21 = 0.8821 A

Answer

I_R1 = 0.8821 A

5.RC & RL transients

Answer: τ = 22.69 ms

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e^−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Thévenin equivalent seen by the capacitor

Short the source to find R_th; open the capacitor to find the voltage it will settle at.

R_th = R₁ ∥ R₂ = 1·2.2/(1 + 2.2) = 0.6875 kΩ

v_C(∞) = 24·2.2/(1 + 2.2) = 16.5 V

Time constant

τ = R_th·C = 0.6875·33 = 22.69 ms

Answer

τ = 22.69 ms

6.RC & RL transients

Answer: v_C = 5.626 V

Initial capacitor voltage

In steady state the capacitor is an open circuit, so R₁ and R₂ form a voltage divider. The capacitor voltage cannot jump when the switch opens.

v_C(0) = 24·3.3/(3.3 + 3.3) = 12 V

Time constant after the switch opens

τ = R₂·C = 3.3·100 = 330 ms

Discharge

v_C(t) = 12·e^−250/330 = 5.626 V

Answer

v_C = 5.626 V

7.Magnetic fields & induction

Answer: B = 84 µT

Magnetic field of currents: around a long straight wire the field lines are circles (right-hand grip rule) with B = μ₀I/(2πr). At the centre of a flat circular coil of N turns, B = μ₀NI/(2R). Inside a long solenoid the field is uniform, B = μ₀nI with n = N/L turns per metre, whatever the radius. μ₀ = 4π × 10⁻⁷ T·m/A. Work in SI units (metres and amperes), and add the fields of several sources as vectors.

Field of each wire at P

B₁ = 2 × 10⁻⁷·12/0.1 = 24 µT

B₂ = 2 × 10⁻⁷·30/0.1 = 60 µT

Combine

B = B₁ + B₂ = 84 µT

Answer

B = 84 µT

8.Magnetic fields & induction

Answer: E_rms = 3.554 V

Electromagnetic induction: the flux through a loop is Φ = BA·cos θ, with θ between B and the normal of the loop. Faraday's law: a change of flux induces emf = −N·dΦ/dt in a coil of N turns, and Lenz's law says the induced current flows so that its own field opposes the change. A rod moving across a field gives emf = BLv. A coil rotating at ω gives e = NBAω·sin ωt, peak NBAω. Self-inductance: emf = −L·di/dt, with L = μ₀N²A/l for a long solenoid, and the energy stored is W = ½LI². Two coupled coils: emf₂ = −M·di₁/dt with M = k√(L₁L₂).

Angular speed and area

ω = 2π·1500/60 = 157.1 rad/s

A = 0.016 m²

Peak emf

E₀ = NBAω = 20·0.1·0.016·157.1 = 5.027 V

rms value

E_rms = 5.027/√2 = 3.554 V

Answer

E_rms = 3.554 V

9.AC impedance & phasors

Answer: P = 5.222 W

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

X_L = 94.25 Ω, X_C = 56.44 Ω

Impedance

|Z| = √(15² + (37.81)²) = 40.68 Ω

Real power

Inductors and capacitors only store and return energy; the resistor absorbs all of the real power.

I = 24/40.68 = 0.59 A

P = I²·R = 0.59²·15 = 5.222 W

Answer

P = 5.222 W

10.AC impedance & phasors

Answer: V_L = 67.42 V

Resonance

At resonance the reactances cancel, so the impedance is just R.

ω₀ = 1/√(LC) = 1/√(0.1·0.22·10⁻⁶) = 6742 rad/s

I = V/R = 5/50 = 0.1 A

Voltage across the inductor

X_L = ω₀L = 6742·0.1 = 674.2 Ω

V_L = I·X_L = 0.1·674.2 = 67.42 V

Answer

V_L = 67.42 V

This is Q = 13.48 times the supply voltage.

ExamProblems · examproblems.com/courses/physics-2-electricity-and-magnetism