Physics 2: Electricity and Magnetism: cram pack

Formula sheets, the key method steps for every topic and 10 practice problems, with full solutions at the back.

New problems Back to the course

In the print window, choose “Save as PDF” to keep a copy on your device.

1Formulas and methods

Coulomb’s law & electric fields

Coulomb’s law: F = k·|q₁q₂|/r²
Field of a point charge: E = k·|q|/r²
Constant: k = 8.99 × 10⁹ N·m²/C²
Force on a charge: F = q·E

Series & parallel resistors

Resistors in series: R_eq = R₁ + R₂ + …
Resistors in parallel: 1/R_eq = 1/R₁ + 1/R₂ + …
Two in parallel: R_eq = R₁R₂ / (R₁ + R₂)
Ohm's law: V = I·R
Power: P = V·I = I²R = V²/R

Method

Start at the end of the network furthest from the terminals.
Combine resistors in series by adding them, and resistors in parallel with 1/R = 1/R₁ + 1/R₂ + …
Redraw the circuit after each step.
Repeat until one resistor is left between the terminals.

RC & RL transients

Time constant: τ = RC | τ = L/R
Response: x(t) = x(∞) + [x(0) − x(∞)]·e^−t/τ
Capacitor at DC: open circuit; v_C cannot jump
Inductor at DC: short circuit; i_L cannot jump
Settled: t ≈ 5τ

Method

Find the initial value just after switching: a capacitor voltage and an inductor current cannot jump.
Find the final value long after switching: a capacitor acts as an open circuit, an inductor as a short circuit.
Find the time constant: τ = RC or τ = L/R, using the resistance seen by the capacitor or inductor.
Use x(t) = x(∞) + [x(0) − x(∞)]·e^−t/τ.

Magnetic fields & induction

Long straight wire: B = μ₀I/(2πr)
Centre of a flat coil: B = μ₀NI/(2R)
Long solenoid: B = μ₀nI, n = N/L
Constant: μ₀ = 4π × 10⁻⁷ T·m/A
Force on a wire: F = BIL·sin θ
Force on a charge: F = |q|vB·sin θ
Circular motion: r = mv/(|q|B), T = 2πm/(|q|B)
Parallel wires: F/L = μ₀I₁I₂/(2πd)
Flux: Φ = BA·cos θ
Faraday’s law: ε = −N·ΔΦ/Δt
Moving rod: ε = BLv
Generator: E₀ = NBAω, E_rms = E₀/√2
Inductance: ε = L·ΔI/Δt, L = μ₀N²A/l, W = ½LI²
Mutual inductance: ε₂ = M·di₁/dt, M = k√(L₁L₂)
Velocity selector and spectrometer: v = E/B, r = √(2mV/|q|)/B

Method

Convert every quantity to SI units: cm to m, cm² to m², mT and µT to T.
Pick the right formula: B = μ₀I/(2πr) for a wire, μ₀NI/(2R) for the centre of a coil, μ₀nI inside a solenoid; F = BIL·sin θ or |q|vB·sin θ for forces.
For induction, find the change of flux ΔΦ = Δ(BA·cos θ) and use ε = N·ΔΦ/Δt, or ε = BLv for a moving rod and NBAω for a rotating coil.
Find directions separately with the right-hand rules, and Lenz’s law for induced currents.

AC impedance & phasors

Impedances: Z_R = R, Z_L = jωL, Z_C = 1/(jωC)
Angular frequency: ω = 2πf
Magnitude and angle: |Z| = √(R² + X²), φ = atan(X/R)
Phasor Ohm’s law: V = I·Z

Method

Convert the frequency: ω = 2πf.
Find each reactance: X_L = ωL and X_C = 1/(ωC).
Add impedances like resistors, with Z = R + jX.
Find the magnitude |Z| = √(R² + X²) and the angle φ = atan(X/R), then use Ohm’s law with phasors.

2Practice problems

1.Coulomb’s law & electric fieldsMedium

Three point charges lie on a straight line: +4 µC on the left, −8 µC on the right 30 cm away, and −5 µC between them, 22.5 cm from the left charge. Find the magnitude of the net electric force F on the middle charge. Use k = 8.99 × 10⁹ N·m²/C².

q_L = +4 µCq_R = −8 µCq_M = −5 µCr_L = 22.5 cmr_R = 7.5 cm

F = N

2.Coulomb’s law & electric fieldsHard

An electron enters the uniform field between two parallel plates moving parallel to them at 5 × 10⁷ m/s. The plates are 10 cm long and the field between them is 1700 N/C. Electron charge 1.602 × 10⁻¹⁹ C, mass 9.109 × 10⁻³¹ kg; ignore gravity. How far y is it deflected sideways when it leaves the plates? Give the answer in mm.

v₀ = 5 × 10⁷ m/sL = 10 cmE = 1700 N/Ce = 1.602 × 10⁻¹⁹ Cm_e = 9.109 × 10⁻³¹ kg

y = mm

3.Series & parallel resistorsMedium

Find the current I_R2 through R₂.

V₁ = 12 VR₁ = 3 ΩR₂ = 4 ΩR₃ = 3 ΩR₄ = 8 Ω

I_R2 = A

4.Series & parallel resistorsHard

Find the equivalent resistance R_eq seen by the source V₁.

V₁ = 9 VR₁ = 20 ΩR₂ = 2 ΩR₃ = 12 ΩR₄ = 8 ΩR₅ = 6 ΩR₆ = 2 Ω

R_eq = Ω

5.RC & RL transientsMedium

The inductor carries a steady current of 0.5 A. At t = 0 the switch closes the loop through R and the source is removed, so the inductor current decays through R. Find the current i at t = 20 ms.

i(0) = 0.5 AR = 20 ΩL = 220 mHt = 20 ms

i = A

6.RC & RL transientsHard

The switch across R₂ has been open for a long time, so the inductor current is steady. At t = 0 the switch closes and shorts out R₂. Find the inductor current i at t = 40 ms.

V_s = 10 VR₁ = 10 ΩR₂ = 33 ΩL = 220 mHt = 40 ms

i = A

7.Magnetic fields & inductionMedium

An electron moving at 1 × 10⁶ m/s enters a uniform magnetic field at right angles and moves on a circle of radius 0.07108 cm. Find the magnetic flux density B.

m = 9.109 × 10⁻³¹ kg|q| = 1.602 × 10⁻¹⁹ Cv = 1 × 10⁶ m/sr = 0.07108 cm

B = mT

8.Magnetic fields & inductionHard

A long air-core solenoid has 100 turns, a length of 10 cm and a diameter of 4 cm. Find its self-inductance L.

N = 100l = 10 cm⌀ = 4 cmμ₀ = 4π × 10⁻⁷ T·m/A

L = µH

9.AC impedance & phasorsMedium

A series RLC circuit is connected to a 10 V (rms), 50 Hz supply. Find the rms current I.

V = 10 V (rms)f = 50 HzR = 60 ΩL = 100 mHC = 22 µF

I = A

10.AC impedance & phasorsHard

A resistor R₁ is connected in series with a parallel combination of R₂ and a capacitor C, across a 24 V (rms), 500 Hz supply. Find the rms current I.

V = 24 V (rms)f = 500 HzR₁ = 25 ΩR₂ = 40 ΩC = 2.2 µF

I = A

3Solutions

1.Coulomb’s law & electric fields

Answer: F = 67.48 N

Coulomb’s law: two point charges attract or repel with F = k·|q₁·q₂|/r², with k = 8.99 × 10⁹ N·m²/C². The field of a point charge is E = k·|q|/r², pointing away from a positive charge and towards a negative one. Forces and fields from several charges add as vectors.

Force from each charge

Right is positive.

F_L = −k·4·5 × 10⁻¹²/0.225² = −3.552 N

F_R = −k·8·5 × 10⁻¹²/0.075² = −63.93 N

Net force

F = −3.552 + (−63.93) = −67.48 N → |F| = 67.48 N

Answer

F = 67.48 N

The net force points to the left.

2.Coulomb’s law & electric fields

Answer: y = 0.598 mm

Time between the plates

t = L/v₀ = 0.1/5 × 10⁷ = 2 × 10⁻⁹ s

Sideways acceleration

a = e·E/m = 1.602 × 10⁻¹⁹·1700/9.109 × 10⁻³¹ = 2.99 × 10¹⁴ m/s²

Deflection

y = ½·a·t² = ½·2.99 × 10¹⁴·(2 × 10⁻⁹)² = 0.000598 m = 0.598 mm

Answer

y = 0.598 mm

The electron is pushed towards the positive plate, against the field direction.

3.Series & parallel resistors

Answer: I_R2 = 1.483 A

Series and parallel resistors: in series the same current flows through each resistor and R = R₁ + R₂ + …. In parallel each resistor has the same voltage and 1/R = 1/R₁ + 1/R₂ + …. A ladder network is reduced one pair at a time until a single equivalent resistance remains.

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R₃ + R₄ = 3 + 8 = 11 Ω

R₂ ∥ 11 = 4·11/(4+11) = 2.933 Ω

R_eq = R₁ + 2.933 = 3 + 2.933 = 5.933 Ω

Current from the source

The source sees only R_eq, so Ohm’s law gives the current it delivers. That current flows through R₁.

I_R1 = V₁/R_eq = 12/5.933 = 2.022 A

Current through R₂

Subtract the drop across R₁ to get the voltage at node A, which is the voltage across R₂.

V_A = V₁ − I_R1·R₁ = 12 − 2.022·3 = 5.933 V

I_R2 = V_A/R₂ = 5.933/4 = 1.483 A

Answer

I_R2 = 1.483 A

4.Series & parallel resistors

Answer: R_eq = 21.78 Ω

Combine resistors from the far end

Start at the end farthest from the source and work back towards it. Resistors carrying the same current are in series; resistors across the same two nodes are in parallel.

R₅ + R₆ = 6 + 2 = 8 Ω

R₄ ∥ 8 = 4 Ω

R₃ + 4 = 16 Ω

R₂ ∥ 16 = 1.778 Ω

R_eq = R₁ + 1.778 = 20 + 1.778 = 21.78 Ω

Answer

R_eq = 21.78 Ω

5.RC & RL transients

Answer: i = 0.08116 A

First-order transients: in a circuit with one capacitor or one inductor, every voltage and current moves exponentially from its initial value to its final value: x(t) = x(∞) + [x(0) − x(∞)]·e^−t/τ, with τ = RC or τ = L/R. After about 5τ the circuit has settled.

Time constant

τ = L/R = 220 mH / 20 Ω = 11 ms

Decay of the current

i(t) = 0.5·e^−20/11 = 0.08116 A

Answer

i = 0.08116 A

6.RC & RL transients

Answer: i = 0.8754 A

Initial value, final value, time constant

Before t = 0 both resistors are in the loop; afterwards the closed switch bypasses R₂.

i(0) = 10/(10 + 33) = 0.2326 A

i(∞) = 10/10 = 1 A

τ = L/R = 220/10 = 22 ms

i(t) = 1 + (0.2326 − 1)·e^−t/τ

Current at the given time

i(40) = 1 + (−0.7674)·e^−40/22 = 0.8754 A

Answer

i = 0.8754 A

7.Magnetic fields & induction

Answer: B = 7.999 mT

Magnetic forces: a straight wire carrying I in a field B feels F = BIL·sin θ, and a moving charge F = |q|vB·sin θ, where θ is the angle between the current (or velocity) and B. The force is perpendicular to both: point the fingers of the right hand along I or v, curl them towards B, and the thumb gives F for a positive charge; reverse it for a negative charge. Because F is perpendicular to v, a charge moving across a uniform field moves on a circle: |q|vB = mv²/r gives r = mv/(|q|B) and the period T = 2πm/(|q|B), which does not depend on the speed. Two parallel wires attract for currents in the same direction: F/L = μ₀I₁I₂/(2πd).

Field from the radius

B = mv/(|q|r) = 9.109 × 10⁻³¹·1 × 10⁶/(1.602 × 10⁻¹⁹·0.0007108) = 7.999 mT

Answer

B = 7.999 mT

8.Magnetic fields & induction

Answer: L = 157.9 µH

Electromagnetic induction: the flux through a loop is Φ = BA·cos θ, with θ between B and the normal of the loop. Faraday's law: a change of flux induces emf = −N·dΦ/dt in a coil of N turns, and Lenz's law says the induced current flows so that its own field opposes the change. A rod moving across a field gives emf = BLv. A coil rotating at ω gives e = NBAω·sin ωt, peak NBAω. Self-inductance: emf = −L·di/dt, with L = μ₀N²A/l for a long solenoid, and the energy stored is W = ½LI². Two coupled coils: emf₂ = −M·di₁/dt with M = k√(L₁L₂).

Cross-section

A = π·(0.02)² = 0.001257 m²

Self-inductance

L = μ₀N²A/l = 4π × 10⁻⁷·100²·0.001257/0.1 = 0.0001579 H = 157.9 µH

Answer

L = 157.9 µH

9.AC impedance & phasors

Answer: I = 0.07802 A

AC circuits with phasors: resistors, inductors and capacitors have impedances R, jωL and 1/(jωC), with ω = 2πf. In series, impedances add like resistances, but as complex numbers. Rms current and voltage follow Ohm’s law with |Z|.

Reactances

ω = 2πf = 2π·50 = 314.2 rad/s

X_L = ωL = 314.2·0.1 = 31.42 Ω

X_C = 1/(ωC) = 1/(314.2·22·10⁻⁶) = 144.7 Ω

Impedance

In series the impedances add as complex numbers: Z = R + j(X_L − X_C).

|Z| = √(R² + (X_L − X_C)²) = √(60² + (−113.3)²) = 128.2 Ω

Current

The same current flows through every element of a series circuit.

I = V/|Z| = 10/128.2 = 0.07802 A

Answer

I = 0.07802 A

10.AC impedance & phasors

Answer: I = 0.3809 A

Reactance

X_C = 1/(2π·500·2.2·10⁻⁶) = 144.7 Ω

Parallel combination

Multiply top and bottom by the complex conjugate to split Z_p into real and imaginary parts.

Z_p = R₂·(−jX_C)/(R₂ − jX_C) = (R₂·X_C² − jR₂²·X_C)/(R₂² + X_C²)

Z_p = 37.16 − j10.27 Ω

Total impedance

Z = 25 + 37.16 − j10.27 = 62.16 − j10.27 Ω

|Z| = √(62.16² + 10.27²) = 63 Ω

Current

I = V/|Z| = 24/63 = 0.3809 A

Answer

I = 0.3809 A

ExamProblems · examproblems.com/courses/physics-2-electricity-and-magnetism