Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 108 km/h sees an obstacle. Her reaction time is 1.4 s, after which the car brakes with a constant deceleration of 7.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 108 km/htr = 1.4 sa = −7.5 m/s²
d = m
2.KinematicsHard
A tram starts from rest and accelerates at 2.5 m/s² for 6 s, then runs at constant speed for 9 s, and finally brakes at 2.5 m/s² until it stops. Find the total distance s between the two stops.
a1 = 2.5 m/s²t1 = 6 st2 = 9 sa3 = −2.5 m/s²
s = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 12 m/s and comes to rest after 73 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 12 m/sd = 73 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 3.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4.5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 3.5 kgm2 = 4.5 kgμ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 24 m/s and must land 20 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 24 m/sR = 20 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is thrown from ground level at 31 m/s and 40° above the horizontal. It lands on the flat roof of a building 13 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 31 m/sθ = 40°hroof = 13 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 1000 N/m. A 0.5 kg ball is placed on it and the spring is compressed by 10 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.5 kgk = 1000 N/mx = 10 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 3 kg block rests on a rough horizontal table (μ = 0.1). A light string runs from it over a smooth pulley at the edge of the table to a hanging 2 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 3 m.
m1 = 3 kgm2 = 2 kgμ = 0.1d = 3 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1 kg glider moving at 9 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 1 kgm2 = 5 kgv1 = 9 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 5 g bullet is fired horizontally into a 3 kg block hanging from light strings 1.2 m long, and stays in it. The strings swing out to a largest angle of 15° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 3 kgL = 1.2 mθ = 15°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 200 mm to 100 mm. In the wide section the pressure is 260 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A closed water tank has compressed air above the water at a gauge pressure of 90 kPa. Water leaves through an opening with a diameter of 40 mm, 1 m below the water surface, into the open air. Ignoring losses, find the jet velocity v. Use g = 9.81 m/s².
A reversible refrigerator keeps a cold room at 4 °C by removing 6 kW of heat, and rejects heat to the surroundings at 25 °C. Find the rate Q̇H at which it rejects heat.
TL = 4 °CTH = 25 °CQ̇L = 6 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat engine takes in 2700 kJ of heat from a reservoir at 350 °C, produces 702 kJ of work and rejects the rest to a reservoir at 25 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 350 °CTL = 25 °CQH = 2700 kJW = 702 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
An object stands 60 cm in front of a thin converging lens with a focal length of 20 cm. Find the magnification m (negative for an inverted image).
do = 60 cmf = 20 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 405 nm falls at right angles on a grating with 600 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 600 mm⁻¹λ = 405 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: d = 102 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Reaction distance
d1 = v₀·tr = 30·1.4 = 42 m
Braking distance
d2 = v₀²/(2a) = 30²/(2·7.5) = 60 m
Total
d = 42 + 60 = 102 m
Answer
d = 102 m
2.Kinematics
Answer: s = 225 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2.5·6 = 15 m/s
Distance of each phase
s1 = ½·2.5·6² = 45 m
s2 = 15·9 = 135 m
s3 = 15²/(2·2.5) = 45 m
Total distance
s = 45 + 135 + 45 = 225 m
Answer
s = 225 m
3.Newton’s laws
Answer: μ = 0.1005
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 12²/(2·73) = 0.9863 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 0.9863/9.81 = 0.1005
Answer
μ = 0.1005
4.Newton’s laws
Answer: a = 5.089 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·20/24² = 0.3406
Angle
2θ = 19.91° → θ = 9.957°
Answer
θ = 9.957°
The other solution is 90° − θ = 80.04°.
6.Projectile motion
Answer: x = 77.08 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 23.75 m/s, vy = 19.93 m/s
Time to land on the roof
Larger root: the ball is descending.
13 = 19.93·t − 4.905·t²
t = (19.93 + √(19.93² − 2·9.81·13))/9.81 = 3.246 s
Horizontal distance
x = vx·t = 23.75·3.246 = 77.08 m
Answer
x = 77.08 m
7.Work & energy
Answer: h = 1.019 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 10 cm = 0.1 m
½kx² = ½·1000·0.1² = 5 J
Height
m·g = 0.5·9.81 = 4.905 N
h = ½kx²/(mg) = 5/4.905 = 1.019 m
Answer
h = 1.019 m
8.Work & energy
Answer: v = 4.474 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 19.62·3 = 58.86 J
μ·m₁g·d = 0.1·29.43·3 = 8.829 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 50.03 → v = √(2·50.03/5) = 4.474 m/s
Answer
v = 4.474 m/s
9.Momentum & collisions
Answer: v′1 = −6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1 − 5)/(1 + 5)·9 = −6 m/s
v′2 = 2·1/(1 + 5)·9 = 3 m/s
Answer
v′1 = −6 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: v = 538.3 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.2·(1 − cos 15°) = 0.04089 m
Speed after impact
V = √(2·9.81·0.04089) = 0.8957 m/s
Collision
v = (m + M)·V/m = 3.005·0.8957/0.005 = 538.3 m/s
Answer
v = 538.3 m/s
11.Hydrostatic force
Answer: F = 239.1 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·7.5 = 239.1 kN
Answer
F = 239.1 kN
12.Hydrostatic force
Answer: ycp = 2.333 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·1.5 = 33.11 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(90000/1000 + 9.81·1)) = 14.13 m/s
Answer
v = 14.13 m/s
15.Ideal gas law
Answer: V = 30.25 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 350/44.01 = 7.953 mol
T = 70 + 273.15 = 343.1 K
Volume
V = nRT/P = 7.953·8.314·343.1/750 = 30.25 L
Answer
V = 30.25 L
16.Ideal gas law
Answer: ρ = 4.171 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 120 + 273.15 = 393.1 K
Density
ρ = 850·16.04/(8.314·393.1) = 4.171 kg/m³
Answer
ρ = 4.171 kg/m³
17.Heat engines & refrigerators
Answer: Q̇H = 6.455 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 25 + 273.15 = 298.1 K
TL = 4 + 273.15 = 277.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 6·298.1/277.1 = 6.455 kW
Answer
Q̇H = 6.455 kW
Power input: Ẇ = 0.4546 kW.
18.Heat engines & refrigerators
Answer: Sgen = 2.368 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 2700 − 702 = 1998 kJ
Absolute temperatures
TH = 350 + 273.15 = 623.1 K
TL = 25 + 273.15 = 298.1 K
Entropy changes of the reservoirs
ΔSH = −2700/623.1 = −4.333 kJ/K
ΔSL = 1998/298.1 = 6.701 kJ/K
Sgen = 6.701 − 4.333 = 2.368 kJ/K
Answer
Sgen = 2.368 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: m = −0.5
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/20 − 1/60
di = 30 cm
Magnification
m = −di/do = −30/60 = −0.5
Answer
m = −0.5
20.Waves, sound & optics
Answer: θ1 = 14.06 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …