Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 2 m/s² along a runway. Find its speed v after 800 m.
v₀ = 0a = 2 m/s²s = 800 m
v = m/s
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 32 m/s² for 2 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². How long after launch does it hit the ground? Find t.
a = 32 m/s²t1 = 2 sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 16 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 16 kgθ = 35°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 130 N pulls the front 3 kg block; the 4 kg block is towed behind. The coefficient of kinetic friction is 0.3 for both blocks. Use g = 9.81 m/s². Find the acceleration a of the blocks.
m1 = 4 kgm2 = 3 kgF = 130 Nμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 26 m/s and 70° above the horizontal towards a wall 35 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 26 m/sθ = 70°x = 35 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 17 m/s and 45° above the horizontal from the top of a 40 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 17 m/sθ = 45°h = 40 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 0.5 kg block slides 20 m down a slope at 30° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 0.5 kgθ = 30°μ = 0.3d = 20 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 4 kg block is released from rest at height 2.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1 m long (μ = 0.1) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 2.5 mL = 1 mμ = 0.1k = 500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 10 g bullet is fired horizontally into a 1.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 10 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 1.5 kgh = 10 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.3 kg ball hits a wall at 20 m/s and bounces straight back at 14 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.3 kgvin = 20 m/svout = 14 m/sΔt = 20 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 30 mm. The water level is kept 2.5 m above the orifice and the discharge coefficient is 0.6. Find the flow rate Q. Use g = 9.81 m/s².
d = 30 mmh = 2.5 mCd = 0.6g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A hose with an inner diameter of 20 mm siphons water from an open tank. The highest point C of the hose is 0.5 m above the water surface, and the outlet (open to the air) is 3 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 20 mmzC = +0.5 mz2 = −3 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
A tank of 50 L contains 10 g of CH₄ at 80 °C. Treat it as an ideal gas and find the pressure P.
A reversible (Carnot) heat engine takes in 1800 kJ of heat from a reservoir at 550 °C and rejects 718 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 550 °CQH = 1800 kJQL = 718 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is 7 °C outside, delivering 9 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = 7 °CQ̇H = 9 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe open at both ends is 1 m long. The speed of sound is 343 m/s. Find the frequency f3 of its harmonic number 3.
v = 343 m/sn = 3L = 1 m
f3 = Hz
20.Waves, sound & opticsHard
Light of wavelength 633 nm passes through a single slit 0.15 mm wide. Find the width w of the central bright maximum on a screen 2.5 m away (between the first dark fringes on either side).
λ = 633 nma = 0.15 mmL = 2.5 m
w = mm
3Solutions
1.Kinematics
Answer: v = 56.57 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·2·800) = 56.57 m/s
Answer
v = 56.57 m/s
(203.6 km/h)
2.Kinematics
Answer: t = 15.98 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 32·2 = 64 m/s
h₁ = ½·32·2² = 64 m
Free flight to the ground
Solve −h₁ = v₁·t₂ − ½·g·t₂² for the positive root.
t₂ = (64 + √(64² + 2·9.81·64))/9.81 = 13.98 s
t = 2 + 13.98 = 15.98 s
Answer
t = 15.98 s
3.Newton’s laws
Answer: a = 3.216 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 26·cos 70° = 8.893 m/s
t = x/vx = 35/8.893 = 3.936 s
Height at that time
y = 24.43·3.936 − ½·9.81·3.936² = 20.18 m
Answer
y = 20.18 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: H = 47.36 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 17·sin 45° = 12.02 m/s
Rise above the cliff
Δh = vy²/(2g) = 12.02²/(2·9.81) = 7.365 m
Height above the ground
H = 40 + 7.365 = 47.36 m
Answer
H = 47.36 m
7.Work & energy
Answer: Wf = 25.49 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 4.905·0.866 = 4.248 N
F = μN = 0.3·4.248 = 1.274 N
Work against friction
Wf = F·d = 1.274·20 = 25.49 J
Answer
Wf = 25.49 J
8.Work & energy
Answer: x = 61.38 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(2.5 − 0.1·1) = 94.18 J
Maximum compression
½kx² = 94.18 → x = √(2·94.18/500) = 0.6138 m = 61.38 cm
Answer
x = 61.38 cm
9.Momentum & collisions
Answer: v = 211.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.1) = 1.401 m/s
Collision
m·v = (m + M)·V → v = (0.01 + 1.5)·1.401/0.01 = 211.5 m/s
Answer
v = 211.5 m/s
10.Momentum & collisions
Answer: J = 10.2 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.3·(14 + 20) = 10.2 N·s
Answer
J = 10.2 N·s
11.Hydrostatic force
Answer: F = 58.86 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·2 = 58.86 kN
Answer
F = 58.86 kN
12.Hydrostatic force
Answer: F = 69.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1.5/2 = 4.75 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.75·1.5 = 69.9 kN
Answer
F = 69.9 kN
13.Continuity & Bernoulli
Answer: Q = 2.97 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·2.5) = 7.004 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 550 + 273.15 = 823.1 K
Reversible heat ratio
TL = TH·QL/QH = 823.1·718/1800 = 328.3 K = 55.2 °C
Answer
TL = 55.2 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.4574 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 9/19.68 = 0.4574 kW
Answer
Ẇmin = 0.4574 kW
19.Waves, sound & optics
Answer: f3 = 514.5 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·1/3 = 0.6667 m
Frequency
f = v/λ = 343/0.6667 = 514.5 Hz
Answer
f3 = 514.5 Hz
20.Waves, sound & optics
Answer: w = 21.1 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …