Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 45 km/h brakes with a constant deceleration of 5.5 m/s² until it stops. Find the braking distance s.
v₀ = 45 km/ha = −5.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 7 m/s from the edge of a roof 5 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 7 m/sh₀ = 5 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 8.5 m/s and comes to rest after 74 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 8.5 m/sd = 74 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 5.5 m/s. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 5.5 m/sθ = 25°μ = 0.2g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched from level ground at 35° above the horizontal and lands 150 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 35°R = 150 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 40° above horizontal from the top of a 25 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 32 m/sθ = 40°h = 25 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 4 kg block slides 10 m down a slope at 45° to the horizontal, with a coefficient of kinetic friction of 0.35. Find the work Wf done against friction.
m = 4 kgθ = 45°μ = 0.35d = 10 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.1) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 0.5 kgh = 5 mL = 3 mμ = 0.1k = 2000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 10 g bullet is fired horizontally into a 3 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 9 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 3 kgh = 9 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.6 kg ball hits a wall at 8 m/s and bounces straight back at 17 m/s. The contact lasts 25 ms. Find the average force Favg of the wall on the ball.
m = 0.6 kgvin = 8 m/svout = 17 m/sΔt = 25 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 3 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 270 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 50 mm siphons water from an open tank. The highest point C of the hose is 3 m above the water surface, and the outlet (open to the air) is 1.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 50 mmzC = +3 mz2 = −1.5 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
A tank of 10 L contains 500 g of O₂ at 85 °C. Treat it as an ideal gas and find the pressure P.
A reversible refrigerator keeps a cold room at -25 °C by removing 6.5 kW of heat, and rejects heat to the surroundings at 28 °C. Find the rate Q̇H at which it rejects heat.
TL = -25 °CTH = 28 °CQ̇L = 6.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 500 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 20 °C. Both engines have the same thermal efficiency. Find Tm in °C.
TH = 500 °CTL = 20 °C
Tm = °C
19.Waves, sound & opticsMedium
An object stands 30 cm in front of a thin converging lens with a focal length of 20 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 30 cmf = 20 cm
di = cm
20.Waves, sound & opticsHard
A diffraction grating has 1200 lines per millimetre. Light of wavelength 656 nm falls on it at right angles. What is the highest order mmax of bright maximum that can be seen?
N = 1200 mm⁻¹λ = 656 nm
mmax =
3Solutions
1.Kinematics
Answer: s = 14.2 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 45/3.6 = 12.5 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 12.5²/(2·5.5) = 14.2 m
Answer
s = 14.2 m
2.Kinematics
Answer: t = 1.95 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−5 = 7·t − ½·9.81·t²
4.905·t² − 7·t − 5 = 0
Solve the quadratic
Only the positive root is physical.
t = (7 + √(7² + 2·9.81·5))/9.81 = 1.95 s
Answer
t = 1.95 s
3.Newton’s laws
Answer: μ = 0.04976
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 8.5²/(2·74) = 0.4882 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 0.4882/9.81 = 0.04976
Answer
μ = 0.04976
4.Newton’s laws
Answer: d = 2.553 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.2·cos 25°) = 5.924 m/s²
Distance
d = v₀²/(2a) = 5.5²/(2·5.924) = 2.553 m
Answer
d = 2.553 m
5.Projectile motion
Answer: v0 = 39.57 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·150/sin 70°) = 39.57 m/s
Answer
v0 = 39.57 m/s
6.Projectile motion
Answer: t = 5.178 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 32·cos 40° = 24.51 m/s
vy = v0·sin θ = 32·sin 40° = 20.57 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 25 + 20.57·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (20.57 + √(423.1 + 490.5))/9.81 = 5.178 s
Answer
t = 5.178 s
7.Work & energy
Answer: Wf = 97.11 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 39.24·0.7071 = 27.75 N
F = μN = 0.35·27.75 = 9.711 N
Work against friction
Wf = F·d = 9.711·10 = 97.11 J
Answer
Wf = 97.11 J
8.Work & energy
Answer: x = 15.18 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(5 − 0.1·3) = 23.05 J
Maximum compression
½kx² = 23.05 → x = √(2·23.05/2000) = 0.1518 m = 15.18 cm
Answer
x = 15.18 cm
9.Momentum & collisions
Answer: v = 400 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.09) = 1.329 m/s
Collision
m·v = (m + M)·V → v = (0.01 + 3)·1.329/0.01 = 400 m/s
Answer
v = 400 m/s
10.Momentum & collisions
Answer: Favg = 600 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.6·(17 + 8) = 15 N·s
Average force
Favg = J/Δt = 15/0.025 = 600 N
Answer
Favg = 600 N
11.Hydrostatic force
Answer: F = 33.11 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·1.5 = 33.11 kN
Answer
F = 33.11 kN
12.Hydrostatic force
Answer: F = 103 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·3 = 103 kN
Answer
F = 103 kN
13.Continuity & Bernoulli
Answer: p2 = 257.2 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 333.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(250/550)·(333.1/283.1) = 1.07 L
Answer
V2 = 1.07 L
17.Heat engines & refrigerators
Answer: Q̇H = 7.888 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 28 + 273.15 = 301.1 K
TL = -25 + 273.15 = 248.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 6.5·301.1/248.1 = 7.888 kW
Answer
Q̇H = 7.888 kW
Power input: Ẇ = 1.388 kW.
18.Heat engines & refrigerators
Answer: Tm = 202.9 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
TL = 20 + 273.15 = 293.1 K
Equal efficiencies
1 − Tm/TH = 1 − TL/Tm gives Tm² = TH·TL.
Tm = √(773.1·293.1) = 476.1 K = 202.9 °C
Answer
Tm = 202.9 °C
19.Waves, sound & optics
Answer: di = 60 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/20 − 1/30
di = 60 cm
Ray diagram
real, on the far side of the lens
Answer
di = 60 cm
20.Waves, sound & optics
Answer: mmax = 1
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …