Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 54 km/h brakes with a constant deceleration of 7.5 m/s² until it stops. Find the braking distance s.
v₀ = 54 km/ha = −7.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 11 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 11 m/sh₀ = 10 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 14 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 14 kgθ = 40°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 30° with a speed of 10 m/s. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 10 m/sθ = 30°μ = 0.2g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 55° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 36 m/sθ = 55°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is thrown from ground level at 37 m/s and 55° above the horizontal. It lands on the flat roof of a building 22 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 37 m/sθ = 55°hroof = 22 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 2 kg block slides 19 m down a slope at 45° to the horizontal, with a coefficient of kinetic friction of 0.25. Find the work Wf done against friction.
m = 2 kgθ = 45°μ = 0.25d = 19 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 5 kg block rests on a rough horizontal table (μ = 0.2). A light string runs from it over a smooth pulley at the edge of the table to a hanging 4 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 2 m.
m1 = 5 kgm2 = 4 kgμ = 0.2d = 2 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 15 kg projectile moving horizontally at 25 m/s explodes into two fragments that move along the same line. The 12 kg fragment continues forwards at 75 m/s. Find the velocity v′2 of the 3 kg fragment (positive in the original direction).
M = 15 kgu = 25 m/sm1 = 12 kgv′1 = 75 m/sm2 = 3 kg
v′2 = m/s
10.Momentum & collisionsHard
At a crossing an 800 kg car travelling east at 24 m/s collides with a 1200 kg car travelling north at 19 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 800 kgv1 = 24 m/s (E)m2 = 1200 kgv2 = 19 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 3 mH = 1 mb = 1 mρ = 1260 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 260 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 200 mm to 75 mm while rising 7 m. At section 1 the pressure is 350 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 4300 kJ of heat from a reservoir at 450 °C and rejects 1684 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 450 °CQH = 4300 kJQL = 1684 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is 2 °C outside, delivering 11 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 21 °CTL = 2 °CQ̇H = 11 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 30 cm in front of a thin diverging lens with a focal length of 20 cm. Find the magnification m (negative for an inverted image).
do = 30 cmf = −20 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 589 nm falls on two slits 0.4 mm apart. The screen is 2 m away. Find the distance y4 from the central bright fringe to bright fringe number 4.
λ = 589 nmd = 0.4 mmL = 2 mm = 4
y4 = mm
3Solutions
1.Kinematics
Answer: s = 15 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 54/3.6 = 15 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 15²/(2·7.5) = 15 m
Answer
s = 15 m
2.Kinematics
Answer: t = 2.937 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−10 = 11·t − ½·9.81·t²
4.905·t² − 11·t − 10 = 0
Solve the quadratic
Only the positive root is physical.
t = (11 + √(11² + 2·9.81·10))/9.81 = 2.937 s
Answer
t = 2.937 s
3.Newton’s laws
Answer: a = 5.554 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 30° + 0.2·cos 30°) = 6.604 m/s²
Distance
d = v₀²/(2a) = 10²/(2·6.604) = 7.571 m
Answer
d = 7.571 m
5.Projectile motion
Answer: t = 6.012 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 36·cos 55° = 20.65 m/s
vy = v0·sin θ = 36·sin 55° = 29.49 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·29.49/9.81 = 6.012 s
Answer
t = 6.012 s
6.Projectile motion
Answer: x = 113.3 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 21.22 m/s, vy = 30.31 m/s
Time to land on the roof
Larger root: the ball is descending.
22 = 30.31·t − 4.905·t²
t = (30.31 + √(30.31² − 2·9.81·22))/9.81 = 5.339 s
Horizontal distance
x = vx·t = 21.22·5.339 = 113.3 m
Answer
x = 113.3 m
7.Work & energy
Answer: Wf = 65.9 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 19.62·0.7071 = 13.87 N
F = μN = 0.25·13.87 = 3.468 N
Work against friction
Wf = F·d = 3.468·19 = 65.9 J
Answer
Wf = 65.9 J
8.Work & energy
Answer: v = 3.617 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 39.24·2 = 78.48 J
μ·m₁g·d = 0.2·49.05·2 = 19.62 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 58.86 → v = √(2·58.86/9) = 3.617 m/s
Answer
v = 3.617 m/s
9.Momentum & collisions
Answer: v′2 = −175 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 15·25 = 375 kg·m/s
Momentum after
375 = 12·75 + 3·v′2
v′2 = (375 − 900)/3 = −175 m/s
Answer
v′2 = −175 m/s
The minus sign means the second fragment flies backwards.
10.Momentum & collisions
Answer: v′ = 14.9 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 450 + 273.15 = 723.1 K
Reversible heat ratio
TL = TH·QL/QH = 723.1·1684/4300 = 283.2 K = 10.06 °C
Answer
TL = 10.06 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.7105 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 11/15.48 = 0.7105 kW
Answer
Ẇmin = 0.7105 kW
19.Waves, sound & optics
Answer: m = 0.4
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−20) − 1/30
di = −12 cm
Magnification
m = −di/do = −(−12)/30 = 0.4
Answer
m = 0.4
20.Waves, sound & optics
Answer: y4 = 11.78 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …