Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 3.75 m/s² along a runway. Find its speed v after 1900 m.
v₀ = 0a = 3.75 m/s²s = 1900 m
v = m/s
2.KinematicsHard
Ball A is dropped from rest from a height of 35 m. At the same instant ball B is thrown straight up from the ground directly below at 15 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 35 mv0B = 15 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
Masses of 9 kg and 6 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 9 kgm2 = 6 kgg = 9.81 m/s²
T = N
4.Newton’s lawsHard
A 6 kg block on a ramp at 40° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 6 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.2. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 6 kgm2 = 6 kgθ = 40°μ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 40° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 24 m/sθ = 40°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is thrown from ground level at 16 m/s and 65° above the horizontal. It lands on the flat roof of a building 2 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 16 m/sθ = 65°hroof = 2 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.2. Find its speed v after it has slid 16 m along the slope.
θ = 20°μ = 0.2d = 16 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A spring of stiffness 5000 N/m at the bottom of a 40° slope is compressed by 10 cm against a 1 kg block and released. The coefficient of kinetic friction between block and slope is 0.1. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 10 g bullet is fired horizontally into a 3 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 24 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 3 kgh = 24 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
At a crossing an 800 kg car travelling east at 24 m/s collides with a 1600 kg car travelling north at 11 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 800 kgv1 = 24 m/s (E)m2 = 1600 kgv2 = 11 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 2.5 mb = 1 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows at 9 L/s through a horizontal pipe that narrows from 150 mm to 75 mm. The pressure in the narrow section is 280 kPa. Ignoring losses, find the pressure p1 in the wide section.
A hose with an inner diameter of 40 mm siphons water from an open tank. The highest point C of the hose is 3 m above the water surface, and the outlet (open to the air) is 5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A heat engine works between a hot reservoir at 425 °C and a cold reservoir at 15 °C. It takes in 3000 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 425 °CTL = 15 °CQH = 3000 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is 7 °C outside, delivering 9 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = 7 °CQ̇H = 9 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
One machine gives a sound level of 75 dB at a certain point. Find the level β at that point when 5 identical machines run at the same time (incoherent sources).
β1 = 75 dBn = 5
β = dB
20.Waves, sound & opticsHard
Light of wavelength 589 nm passes through a single slit 0.08 mm wide. Find the width w of the central bright maximum on a screen 2 m away (between the first dark fringes on either side).
λ = 589 nma = 0.08 mmL = 2 m
w = mm
3Solutions
1.Kinematics
Answer: v = 119.4 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·3.75·1900) = 119.4 m/s
Answer
v = 119.4 m/s
(429.7 km/h)
2.Kinematics
Answer: t = 2.333 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
35 − ½g·t² = 15·t − ½g·t² → t = 35/15 = 2.333 s
Answer
t = 2.333 s
3.Newton’s laws
Answer: T = 70.63 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (9 − 6)·9.81/(9 + 6) = 1.962 m/s²
Tension from the lighter mass
T − m2·g = m2·a → T = 6·(9.81 + 1.962) = 70.63 N
Answer
T = 70.63 N
4.Newton’s laws
Answer: T = 52.86 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 58.86 N
m₁·g·sin θ = 37.83 N
μ·m₁·g·cos θ = 9.018 N
Acceleration of the system
a = (58.86 − 37.83 − 9.018)/12 = 1.001 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 6·(9.81 − 1.001) = 52.86 N
Answer
T = 52.86 N
5.Projectile motion
Answer: x = 57.82 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 40° = 18.39 m/s
vy = v0·sin θ = 24·sin 40° = 15.43 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·15.43/9.81 = 3.145 s
Horizontal distance
x = vx·t = 18.39·3.145 = 57.82 m
Answer
x = 57.82 m
6.Projectile motion
Answer: x = 19.01 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 6.762 m/s, vy = 14.5 m/s
Time to land on the roof
Larger root: the ball is descending.
2 = 14.5·t − 4.905·t²
t = (14.5 + √(14.5² − 2·9.81·2))/9.81 = 2.811 s
Horizontal distance
x = vx·t = 6.762·2.811 = 19.01 m
Answer
x = 19.01 m
7.Work & energy
Answer: v = 6.955 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·16·(0.342 − 0.2·0.9397)) = 6.955 m/s
Answer
v = 6.955 m/s
8.Work & energy
Answer: d = 3.542 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 10 cm = 0.1 m
½kx² = ½·5000·0.1² = 25 J
Energy balance along the slope
m·g = 1·9.81 = 9.81 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 25/(9.81·(0.6428 + 0.1·0.766)) = 3.542 m
Answer
d = 3.542 m
9.Momentum & collisions
Answer: v = 653.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.24) = 2.17 m/s
Collision
m·v = (m + M)·V → v = (0.01 + 3)·2.17/0.01 = 653.2 m/s
Answer
v = 653.2 m/s
10.Momentum & collisions
Answer: v′ = 10.85 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.25·2.5 = 128.8 kN
Answer
F = 128.8 kN
12.Hydrostatic force
Answer: F = 113.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·5.25·2.5 = 113.3 kN
Answer
F = 113.3 kN
13.Continuity & Bernoulli
Answer: p1 = 281.9 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: P = 361.7 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 70/28.01 = 2.499 mol
T = 75 + 273.15 = 348.1 K
Pressure
P = nRT/V = 2.499·8.314·348.1/0.02 = 361.7 kPa
Answer
P = 361.7 kPa
16.Ideal gas law
Answer: V2 = 9.42 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 333.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(300/350)·(333.1/303.1) = 9.42 L
Answer
V2 = 9.42 L
17.Heat engines & refrigerators
Answer: Wmax = 1762 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 425 + 273.15 = 698.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/698.1 = 58.73 %
Maximum work
Wmax = ηmax·QH = 0.5873·3000 = 1762 kJ
Answer
Wmax = 1762 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.4574 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 9/19.68 = 0.4574 kW
Answer
Ẇmin = 0.4574 kW
19.Waves, sound & optics
Answer: β = 81.99 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Total intensity
I = 5·I₁
Level
β = 75 + 10·log₁₀(5) = 81.99 dB
Answer
β = 81.99 dB
20.Waves, sound & optics
Answer: w = 29.45 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …