Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 60 km/h brakes with a constant deceleration of 6 m/s² until it stops. Find the braking distance s.
v₀ = 60 km/ha = −6 m/s²v = 0
s = m
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 3.4 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 3.4 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
An 11 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 11 kgθ = 30°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 20° with a speed of 4 m/s. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 4 m/sθ = 20°μ = 0.2g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 55° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 30 m/sθ = 55°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 50° above horizontal from the top of a 40 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 16 m/sθ = 50°h = 40 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A car travelling at 110 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 110 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A 10 kg block rests on a rough horizontal table (μ = 0.1). A light string runs from it over a smooth pulley at the edge of the table to a hanging 3 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1 m.
m1 = 10 kgm2 = 3 kgμ = 0.1d = 1 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 5 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 5 kgm2 = 0.5 kgv1 = 11 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 2000 kg car runs into a parked 1800 kg car. The wrecks lock together and skid 13 m before stopping. The coefficient of kinetic friction between tyres and road is 0.7. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 3 mb = 1 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 310 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 150 mm to 75 mm while rising 3 m. At section 1 the pressure is 110 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 650 °C and a cold reservoir at 25 °C. It takes in 4000 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 650 °CTL = 25 °CQH = 4000 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat engine takes in 1100 kJ of heat from a reservoir at 350 °C, produces 330 kJ of work and rejects the rest to a reservoir at 35 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 350 °CTL = 35 °CQH = 1100 kJW = 330 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
Light travels in crown glass (n = 1.50) towards a flat boundary with water (n = 1.33). Find the critical angle θc beyond which it is totally reflected.
n1 = 1.50n2 = 1.33
θc = °
20.Waves, sound & opticsHard
Light of wavelength 500 nm passes through a single slit 0.15 mm wide. Find the width w of the central bright maximum on a screen 1 m away (between the first dark fringes on either side).
λ = 500 nma = 0.15 mmL = 1 m
w = mm
3Solutions
1.Kinematics
Answer: s = 23.15 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 60/3.6 = 16.67 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 16.67²/(2·6) = 23.15 m
Answer
s = 23.15 m
2.Kinematics
Answer: d = 51.78 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(3.4 − t₁)
4.905·t₁² + 343·t₁ − 1166 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1166))/(2·4.905) = 3.249 s
Depth
d = ½·9.81·3.249² = 51.78 m
Answer
d = 51.78 m
3.Newton’s laws
Answer: a = 3.631 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 20° + 0.2·cos 20°) = 5.199 m/s²
Distance
d = v₀²/(2a) = 4²/(2·5.199) = 1.539 m
Answer
d = 1.539 m
5.Projectile motion
Answer: x = 86.21 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 30·cos 55° = 17.21 m/s
vy = v0·sin θ = 30·sin 55° = 24.57 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·24.57/9.81 = 5.01 s
Horizontal distance
x = vx·t = 17.21·5.01 = 86.21 m
Answer
x = 86.21 m
6.Projectile motion
Answer: x = 44.91 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 16·cos 50° = 10.28 m/s
vy = v0·sin θ = 16·sin 50° = 12.26 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 40 + 12.26·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (12.26 + √(150.2 + 784.8))/9.81 = 4.366 s
Horizontal distance
x = vx·t = 10.28·4.366 = 44.91 m
Answer
x = 44.91 m
7.Work & energy
Answer: d = 67.98 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 110/3.6 = 30.56 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 30.56²/(2·0.7·9.81) = 67.98 m
Answer
d = 67.98 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 1.737 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 29.43·1 = 29.43 J
μ·m₁g·d = 0.1·98.1·1 = 9.81 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 19.62 → v = √(2·19.62/13) = 1.737 m/s
Answer
v = 1.737 m/s
9.Momentum & collisions
Answer: v′2 = 20 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (5 − 0.5)/(5 + 0.5)·11 = 9 m/s
v′2 = 2·5/(5 + 0.5)·11 = 20 m/s
Answer
v′2 = 20 m/s
10.Momentum & collisions
Answer: v1 = 25.39 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 3/2 = 4 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4·3 = 117.7 kN
Answer
F = 117.7 kN
12.Hydrostatic force
Answer: F = 142.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 3/2 = 5.5 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·5.5·3 = 142.4 kN
Answer
F = 142.4 kN
13.Continuity & Bernoulli
Answer: p2 = 304.3 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 403.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(250/100)·(403.1/288.1) = 34.98 L
Answer
V2 = 34.98 L
17.Heat engines & refrigerators
Answer: Wmax = 2708 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/923.1 = 67.7 %
Maximum work
Wmax = ηmax·QH = 0.677·4000 = 2708 kJ
Answer
Wmax = 2708 kJ
18.Heat engines & refrigerators
Answer: Sgen = 0.7336 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 1100 − 330 = 770 kJ
Absolute temperatures
TH = 350 + 273.15 = 623.1 K
TL = 35 + 273.15 = 308.1 K
Entropy changes of the reservoirs
ΔSH = −1100/623.1 = −1.765 kJ/K
ΔSL = 770/308.1 = 2.499 kJ/K
Sgen = 2.499 − 1.765 = 0.7336 kJ/K
Answer
Sgen = 0.7336 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: θc = 62.46 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.33/1.50 = 0.8867
Critical angle
θc = arcsin(0.8867) = 62.46°
Answer
θc = 62.46°
20.Waves, sound & optics
Answer: w = 6.667 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …