Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 72 km/h brakes with a constant deceleration of 7 m/s² until it stops. How long does braking take? Find t.
v₀ = 72 km/ha = −7 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 9 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 9 m/sh₀ = 10 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 15 kg box is pushed up a ramp at 20° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the pushing force F.
m = 15 kgθ = 20°μ = 0.25g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 3 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1.5 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 3 kgm2 = 1.5 kgμ = 0.3g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 34 m/sθ = 70°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 35° above horizontal from the top of a 60 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 26 m/sθ = 35°h = 60 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 5 kg ball hangs on a light string of length 3 m. It is pulled aside until the string makes 60° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 5 kgL = 3 mθ = 60°g = 9.81 m/s²
T = N
8.Work & energyHard
A 2.5 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.3) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2.5 kgh = 3 mL = 2.5 mμ = 0.3k = 5000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
An 8 g bullet is fired horizontally into a 1 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 23 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 8 gM = 1 kgh = 23 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.35 kg ball hits a wall at 15 m/s and bounces straight back at 17 m/s. The contact lasts 20 ms. Find the average force Favg of the wall on the ball.
m = 0.35 kgvin = 15 m/svout = 17 m/sΔt = 20 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of oil, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 3 mH = 3 mb = 3 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal venturi meter with an inlet diameter of 300 mm and a throat diameter of 150 mm. The pressure at the inlet is 45 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A closed water tank has compressed air above the water at a gauge pressure of 90 kPa. Water leaves through an opening with a diameter of 40 mm, 1 m below the water surface, into the open air. Ignoring losses, find the jet velocity v. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 400 °C and a cold reservoir at 5 °C. Find the highest possible thermal efficiency ηmax.
TH = 400 °CTL = 5 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is -10 °C outside, delivering 6 kW of heat to the house. Find the highest possible coefficient of performance COPmax.
TH = 22 °CTL = -10 °CQ̇H = 6 kW
COPmax =
19.Waves, sound & opticsMedium
A pipe closed at one end is 0.5 m long. The speed of sound is 343 m/s. Find the frequency f7 of its harmonic number 7.
v = 343 m/sn = 7L = 0.5 m
f7 = Hz
20.Waves, sound & opticsHard
Light of wavelength 589 nm falls on two slits 0.1 mm apart. The screen is 1.2 m away. Find the distance y4 from the central bright fringe to bright fringe number 4.
λ = 589 nmd = 0.1 mmL = 1.2 mm = 4
y4 = mm
3Solutions
1.Kinematics
Answer: t = 2.857 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 72/3.6 = 20 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 20/7 = 2.857 s
Answer
t = 2.857 s
2.Kinematics
Answer: t = 2.615 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−10 = 9·t − ½·9.81·t²
4.905·t² − 9·t − 10 = 0
Solve the quadratic
Only the positive root is physical.
t = (9 + √(9² + 2·9.81·10))/9.81 = 2.615 s
Answer
t = 2.615 s
3.Newton’s laws
Answer: F = 84.9 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 50.33 + 34.57 = 84.9 N
Answer
F = 84.9 N
4.Newton’s laws
Answer: T = 12.75 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 34·cos 70° = 11.63 m/s
vy = v0·sin θ = 34·sin 70° = 31.95 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·31.95/9.81 = 6.514 s
Horizontal distance
x = vx·t = 11.63·6.514 = 75.75 m
Answer
x = 75.75 m
6.Projectile motion
Answer: x = 113.6 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 26·cos 35° = 21.3 m/s
vy = v0·sin θ = 26·sin 35° = 14.91 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 60 + 14.91·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (14.91 + √(222.4 + 1177))/9.81 = 5.334 s
Horizontal distance
x = vx·t = 21.3·5.334 = 113.6 m
Answer
x = 113.6 m
7.Work & energy
Answer: T = 98.1 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·3·(1 − cos 60°) = 29.43 m²/s²
Forces at the bottom
m·g = 5·9.81 = 49.05 N
T = mg + mv²/L = 49.05 + 5·29.43/3 = 98.1 N
Answer
T = 98.1 N
Check: T = mg(3 − 2cos θ) = 98.1 N.
8.Work & energy
Answer: x = 14.86 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(3 − 0.3·2.5) = 55.18 J
Maximum compression
½kx² = 55.18 → x = √(2·55.18/5000) = 0.1486 m = 14.86 cm
Answer
x = 14.86 cm
9.Momentum & collisions
Answer: v = 267.7 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.23) = 2.124 m/s
Collision
m·v = (m + M)·V → v = (0.008 + 1)·2.124/0.008 = 267.7 m/s
Answer
v = 267.7 m/s
10.Momentum & collisions
Answer: Favg = 560 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.35·(17 + 15) = 11.2 N·s
Average force
Favg = J/Δt = 11.2/0.02 = 560 N
Answer
Favg = 560 N
11.Hydrostatic force
Answer: F = 239.1 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·7.5 = 239.1 kN
Answer
F = 239.1 kN
12.Hydrostatic force
Answer: ycp = 4.667 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 3/2 = 4.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·4.5·9 = 349.6 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/300)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(90000/1000 + 9.81·1)) = 14.13 m/s
Answer
v = 14.13 m/s
15.Ideal gas law
Answer: V = 554.7 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 130/4.003 = 32.48 mol
T = 35 + 273.15 = 308.1 K
Volume
V = nRT/P = 32.48·8.314·308.1/150 = 554.7 L
Answer
V = 554.7 L
16.Ideal gas law
Answer: V2 = 11.18 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(250/700)·(443.1/283.1) = 11.18 L
Answer
V2 = 11.18 L
17.Heat engines & refrigerators
Answer: ηmax = 58.68 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/673.1 = 58.68 %
Answer
ηmax = 58.68 %
18.Heat engines & refrigerators
Answer: COPmax = 9.223
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·0.5/7 = 0.2857 m
Frequency
f = v/λ = 343/0.2857 = 1201 Hz
Answer
f7 = 1201 Hz
20.Waves, sound & optics
Answer: y4 = 28.27 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …