Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 6.5 m/s² until it stops. Find the braking distance s.
v₀ = 108 km/ha = −6.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 14 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 14 m/sh₀ = 35 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 35 kg sled is pulled across level snow by a rope at 35° above the horizontal with a force of 180 N. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 35 kgF = 180 Nθ = 35°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1 kg block on a ramp at 40° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 6.5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1 kgm2 = 6.5 kgθ = 40°μ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 60° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 18 m/sθ = 60°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 15° above horizontal from the top of a 40 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 31 m/sθ = 15°h = 40 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A car travelling at 30 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.4. Find the stopping distance d.
v = 30 km/hμ = 0.4g = 9.81 m/s²
d = m
8.Work & energyHard
A 10 kg block rests on a rough horizontal table (μ = 0.1). A light string runs from it over a smooth pulley at the edge of the table to a hanging 3 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1 m.
m1 = 10 kgm2 = 3 kgμ = 0.1d = 1 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1000 kg car moving at 7 m/s runs into a stationary 1400 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1000 kgv1 = 7 m/sm2 = 1400 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.25 kg ball hits a wall at 22 m/s and bounces straight back at 15 m/s. The contact lasts 50 ms. Find the average force Favg of the wall on the ball.
m = 0.25 kgvin = 22 m/svout = 15 m/sΔt = 50 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of seawater, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 380 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A closed water tank has compressed air above the water at a gauge pressure of 40 kPa. Water leaves through an opening with a diameter of 25 mm, 2.5 m below the water surface, into the open air. Ignoring losses, find the flow rate Q. Use g = 9.81 m/s².
A reversible (Carnot) heat engine takes in 500 kJ of heat from a reservoir at 250 °C and rejects 290 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 250 °CQH = 500 kJQL = 290 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 50 kW of heat from a source at 900 °C and rejects heat to the surroundings at 30 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -5 °C and also rejects heat to the surroundings at 30 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 900 °CT0 = 30 °CTL = -5 °CQ̇H = 50 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object 1 cm tall stands 8 cm in front of a thin converging lens with a focal length of 30 cm. Find the image height hi (negative for an inverted image).
ho = 1 cmdo = 8 cmf = 30 cm
hi = cm
20.Waves, sound & opticsHard
Light of wavelength 600 nm falls at right angles on a grating with 400 lines per millimetre. Find the angle θ2 of the order-2 maximum.
N = 400 mm⁻¹λ = 600 nmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: s = 69.23 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 30²/(2·6.5) = 69.23 m
Answer
s = 69.23 m
2.Kinematics
Answer: t = 4.456 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−35 = 14·t − ½·9.81·t²
4.905·t² − 14·t − 35 = 0
Solve the quadratic
Only the positive root is physical.
t = (14 + √(14² + 2·9.81·35))/9.81 = 4.456 s
Answer
t = 4.456 s
3.Newton’s laws
Answer: a = 2.498 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 343.4 − 180·sin 35° = 240.1 N
Horizontal forces
m·a = F·cos θ − μ·N = 147.4 − 60.03
a = 87.42/35 = 2.498 m/s²
Answer
a = 2.498 m/s²
4.Newton’s laws
Answer: T = 14.62 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 63.77 N
m₁·g·sin θ = 6.306 N
μ·m₁·g·cos θ = 0.7515 N
Acceleration of the system
a = (63.77 − 6.306 − 0.7515)/7.5 = 7.561 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 6.5·(9.81 − 7.561) = 14.62 N
Answer
T = 14.62 N
5.Projectile motion
Answer: x = 28.6 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 60° = 9 m/s
vy = v0·sin θ = 18·sin 60° = 15.59 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·15.59/9.81 = 3.178 s
Horizontal distance
x = vx·t = 9·3.178 = 28.6 m
Answer
x = 28.6 m
6.Projectile motion
Answer: x = 113.4 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 31·cos 15° = 29.94 m/s
vy = v0·sin θ = 31·sin 15° = 8.023 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 40 + 8.023·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (8.023 + √(64.37 + 784.8))/9.81 = 3.788 s
Horizontal distance
x = vx·t = 29.94·3.788 = 113.4 m
Answer
x = 113.4 m
7.Work & energy
Answer: d = 8.849 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 30/3.6 = 8.333 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 8.333²/(2·0.4·9.81) = 8.849 m
Answer
d = 8.849 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 1.737 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 29.43·1 = 29.43 J
μ·m₁g·d = 0.1·98.1·1 = 9.81 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 19.62 → v = √(2·19.62/13) = 1.737 m/s
Answer
v = 1.737 m/s
9.Momentum & collisions
Answer: ΔK = 14292 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1000·7/2400 = 2.917 m/s
Kinetic energy before and after
Kbefore = ½·1000·7² = 24500 J
Kafter = ½·2400·2.917² = 10208 J
Energy lost
ΔK = 24500 − 10208 = 14292 J
Answer
ΔK = 14292 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 185 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.25·(15 + 22) = 9.25 N·s
Average force
Favg = J/Δt = 9.25/0.05 = 185 N
Answer
Favg = 185 N
11.Hydrostatic force
Answer: F = 68.67 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2/2 = 3.5 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·2 = 68.67 kN
Answer
F = 68.67 kN
12.Hydrostatic force
Answer: ycp = 3.889 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2.5/2 = 3.75 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·3.75·5 = 188.5 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 393.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(150/200)·(393.1/303.1) = 4.863 L
Answer
V2 = 4.863 L
17.Heat engines & refrigerators
Answer: TL = 30.28 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 250 + 273.15 = 523.1 K
Reversible heat ratio
TL = TH·QL/QH = 523.1·290/500 = 303.4 K = 30.28 °C
Answer
TL = 30.28 °C
18.Heat engines & refrigerators
Answer: Q̇L = 284.1 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 900 + 273.15 = 1173 K
T0 = 30 + 273.15 = 303.1 K
TL = -5 + 273.15 = 268.1 K
Engine work
η = 1 − 303.1/1173 = 0.7416
Ẇ = 0.7416·50 = 37.08 kW
Heat removed by the refrigerator
COPR = 268.1/(303.1 − 268.1) = 7.661
Q̇L = 7.661·37.08 = 284.1 kW
Answer
Q̇L = 284.1 kW
19.Waves, sound & optics
Answer: hi = 1.364 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/30 − 1/8
di = −10.91 cm
Magnification and height
m = −(−10.91)/8 = 1.364
hi = 1.364·1 = 1.364 cm
Answer
hi = 1.364 cm
20.Waves, sound & optics
Answer: θ2 = 28.69 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …