Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 60 km/h brakes with a constant deceleration of 7 m/s² until it stops. Find the braking distance s.
v₀ = 60 km/ha = −7 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 2 m/s² for 12 s, then runs at constant speed for 28 s, and finally brakes at 4 m/s² until it stops. Find the total travel time t.
a1 = 2 m/s²t1 = 12 st2 = 28 sa3 = −4 m/s²
t = s
3.Newton’s lawsMedium
A 13 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 13 kgθ = 35°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 7.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 7.5 kgm2 = 1 kgμ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 28 m/s and must land 35 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 28 m/sR = 35 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 34 m/s and 70° above the horizontal from the top of a 60 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 34 m/sθ = 70°h = 60 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A block slides from rest down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.25. Find its speed v after it has slid 20 m along the slope.
θ = 45°μ = 0.25d = 20 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 2 kg block is released from rest at height 4.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.1) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 4.5 mL = 2.5 mμ = 0.1k = 2000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1.5 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 1.5 kgm2 = 5 kgv1 = 2 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 20 g bullet is fired horizontally into a 2 kg block hanging from light strings 1.3 m long, and stays in it. The strings swing out to a largest angle of 30° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 20 gM = 2 kgL = 1.3 mθ = 30°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 1 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of seawater, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 2 mb = 3 mρ = 1025 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 150 mm to 75 mm. In the wide section the pressure is 260 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 40 mm while rising 8 m. At section 1 the pressure is 310 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible (Carnot) heat engine takes in 2800 kJ of heat from a reservoir at 325 °C and rejects 1279 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 325 °CQH = 2800 kJQL = 1279 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -25 °C in a kitchen at 30 °C, removing heat from the cold space at 5 kW. Find the minimum power input Ẇmin.
TH = 30 °CTL = -25 °CQ̇L = 5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe closed at one end is 0.65 m long. The speed of sound is 343 m/s. Find the frequency f7 of its harmonic number 7.
v = 343 m/sn = 7L = 0.65 m
f7 = Hz
20.Waves, sound & opticsHard
An object is 40 cm in front of a concave mirror with a radius of curvature of 16 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 40 cmR = 16 cm
di = cm
3Solutions
1.Kinematics
Answer: s = 19.84 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 60/3.6 = 16.67 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 16.67²/(2·7) = 19.84 m
Answer
s = 19.84 m
2.Kinematics
Answer: t = 46 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2·12 = 24 m/s
Braking time
t3 = v/a3 = 24/4 = 6 s
Total time
t = 12 + 28 + 6 = 46 s
Answer
t = 46 s
3.Newton’s laws
Answer: a = 4.421 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·35/28² = 0.4379
Angle
2θ = 25.97° → θ = 12.99°
Answer
θ = 12.99°
The other solution is 90° − θ = 77.01°.
6.Projectile motion
Answer: H = 112 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 34·sin 70° = 31.95 m/s
Rise above the cliff
Δh = vy²/(2g) = 31.95²/(2·9.81) = 52.03 m
Height above the ground
H = 60 + 52.03 = 112 m
Answer
H = 112 m
7.Work & energy
Answer: v = 14.43 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·20·(0.7071 − 0.25·0.7071)) = 14.43 m/s
Answer
v = 14.43 m/s
8.Work & energy
Answer: x = 28.88 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(4.5 − 0.1·2.5) = 83.39 J
Maximum compression
½kx² = 83.39 → x = √(2·83.39/2000) = 0.2888 m = 28.88 cm
Answer
x = 28.88 cm
9.Momentum & collisions
Answer: v′2 = 0.9231 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1.5 − 5)/(1.5 + 5)·2 = −1.077 m/s
v′2 = 2·1.5/(1.5 + 5)·2 = 0.9231 m/s
Answer
v′2 = 0.9231 m/s
10.Momentum & collisions
Answer: v = 186.7 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.3·(1 − cos 30°) = 0.1742 m
Speed after impact
V = √(2·9.81·0.1742) = 1.849 m/s
Collision
v = (m + M)·V/m = 2.02·1.849/0.02 = 186.7 m/s
Answer
v = 186.7 m/s
11.Hydrostatic force
Answer: F = 44.15 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1/2 = 4.5 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.5·1 = 44.15 kN
Answer
F = 44.15 kN
12.Hydrostatic force
Answer: F = 120.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2/2 = 2 m
A = H·b = 2·3 = 6 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2·6 = 120.7 kN
Answer
F = 120.7 kN
13.Continuity & Bernoulli
Answer: p2 = 230 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli
Work in Pa, then divide by 1000 to get kPa.
v2 = v1·(d1/d2)² = 2·(150/75)² = 8 m/s
½ρ(v1² − v2²) = ½·1000·(2² − 8²)/1000 = −30 kPa
p2 = p1 + ½ρ(v1² − v2²) = 260 + (−30) = 230 kPa
Answer
p2 = 230 kPa
14.Continuity & Bernoulli
Answer: p2 = 212.5 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 325 + 273.15 = 598.1 K
Reversible heat ratio
TL = TH·QL/QH = 598.1·1279/2800 = 273.2 K = 0.07638 °C
Answer
TL = 0.07638 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 1.108 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 5/4.512 = 1.108 kW
Answer
Ẇmin = 1.108 kW
19.Waves, sound & optics
Answer: f7 = 923.5 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·0.65/7 = 0.3714 m
Frequency
f = v/λ = 343/0.3714 = 923.5 Hz
Answer
f7 = 923.5 Hz
20.Waves, sound & optics
Answer: di = 10 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.