Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 220 km/h to take off and the usable runway is 1900 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 220 km/hs = 1900 m
a = m/s²
2.KinematicsHard
A ball is thrown straight up at 18 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 18 m/sh₀ = 20 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 15 kg box is pushed up a ramp at 30° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the pushing force F.
m = 15 kgθ = 30°μ = 0.2g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 1.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1.5 kgm2 = 4 kgμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 25° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 14 m/sθ = 25°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 24 m/s and 25° above the horizontal from the top of a 30 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 24 m/sθ = 25°h = 30 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 10 kg block slides 14 m down a slope at 45° to the horizontal, with a coefficient of kinetic friction of 0.15. Find the work Wf done against friction.
m = 10 kgθ = 45°μ = 0.15d = 14 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.2) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 3 mL = 2.5 mμ = 0.2k = 4000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 20 kg projectile moving horizontally at 14 m/s explodes into two fragments that move along the same line. The 9 kg fragment continues forwards at 28 m/s. Find the velocity v′2 of the 11 kg fragment (positive in the original direction).
M = 20 kgu = 14 m/sm1 = 9 kgv′1 = 28 m/sm2 = 11 kg
v′2 = m/s
10.Momentum & collisionsHard
A 1600 kg car runs into a parked 1900 kg car. The wrecks lock together and skid 18.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.7. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
A pitot-static tube in a wind tunnel reads a difference of 900 Pa between the stagnation pressure and the static pressure. The air density is 1.2 kg/m³. Find the air speed v.
p0 − p = 900 Paρ = 1.2 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 25 mm while rising 1 m. At section 1 the pressure is 240 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 775 °C and a cold reservoir at 40 °C. It takes in 1300 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 775 °CTL = 40 °CQH = 1300 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is 2 °C outside, delivering 15 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 21 °CTL = 2 °CQ̇H = 15 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe closed at one end is 1 m long. The speed of sound is 343 m/s. Find the frequency f5 of its harmonic number 5.
v = 343 m/sn = 5L = 1 m
f5 = Hz
20.Waves, sound & opticsHard
Two thin lenses share an axis, 50 cm apart: lens 1 with f₁ = 5 cm and lens 2 with f₂ = 8 cm. An object stands 12 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 5 cmf2 = 8 cms = 50 cmdo = 12 cm
di2 = cm
3Solutions
1.Kinematics
Answer: a = 0.9828 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 220/3.6 = 61.11 m/s
Acceleration
a = v²/(2s) = 61.11²/(2·1900) = 0.9828 m/s²
Answer
a = 0.9828 m/s²
2.Kinematics
Answer: t = 4.563 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−20 = 18·t − ½·9.81·t²
4.905·t² − 18·t − 20 = 0
Solve the quadratic
Only the positive root is physical.
t = (18 + √(18² + 2·9.81·20))/9.81 = 4.563 s
Answer
t = 4.563 s
3.Newton’s laws
Answer: F = 99.06 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 73.57 + 25.49 = 99.06 N
Answer
F = 99.06 N
4.Newton’s laws
Answer: T = 12.84 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 25° = 12.69 m/s
vy = v0·sin θ = 14·sin 25° = 5.917 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 5.917²/(2·9.81) = 1.784 m
Answer
H = 1.784 m
6.Projectile motion
Answer: H = 35.24 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 24·sin 25° = 10.14 m/s
Rise above the cliff
Δh = vy²/(2g) = 10.14²/(2·9.81) = 5.243 m
Height above the ground
H = 30 + 5.243 = 35.24 m
Answer
H = 35.24 m
7.Work & energy
Answer: Wf = 145.7 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 98.1·0.7071 = 69.37 N
F = μN = 0.15·69.37 = 10.41 N
Work against friction
Wf = F·d = 10.41·14 = 145.7 J
Answer
Wf = 145.7 J
8.Work & energy
Answer: x = 15.66 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(3 − 0.2·2.5) = 49.05 J
Maximum compression
½kx² = 49.05 → x = √(2·49.05/4000) = 0.1566 m = 15.66 cm
Answer
x = 15.66 cm
9.Momentum & collisions
Answer: v′2 = 2.545 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 20·14 = 280 kg·m/s
Momentum after
280 = 9·28 + 11·v′2
v′2 = (280 − 252)/11 = 2.545 m/s
Answer
v′2 = 2.545 m/s
10.Momentum & collisions
Answer: v1 = 34.87 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·900/1.2) = 38.73 m/s
Answer
v = 38.73 m/s
14.Continuity & Bernoulli
Answer: p2 = 167.7 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 775 + 273.15 = 1048 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 313.1/1048 = 70.12 %
Maximum work
Wmax = ηmax·QH = 0.7012·1300 = 911.6 kJ
Answer
Wmax = 911.6 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.9689 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 15/15.48 = 0.9689 kW
Answer
Ẇmin = 0.9689 kW
19.Waves, sound & optics
Answer: f5 = 428.8 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·1/5 = 0.8 m
Frequency
f = v/λ = 343/0.8 = 428.8 Hz
Answer
f5 = 428.8 Hz
20.Waves, sound & optics
Answer: di2 = 9.915 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.