Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 2.75 m/s² along a runway. Find its speed v after 1700 m.
v₀ = 0a = 2.75 m/s²s = 1700 m
v = m/s
2.KinematicsHard
A tram starts from rest and accelerates at 3 m/s² for 12 s, then runs at constant speed for 12 s, and finally brakes at 2 m/s² until it stops. Find the total distance s between the two stops.
a1 = 3 m/s²t1 = 12 st2 = 12 sa3 = −2 m/s²
s = m
3.Newton’s lawsMedium
A 15 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 15 kgθ = 45°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 1 kgm2 = 5 kgμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 45° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 36 m/sθ = 45°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 12 m/s and 40° above the horizontal from the top of a 60 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 12 m/sθ = 40°h = 60 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A block slides from rest down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.2. Find its speed v after it has slid 3 m along the slope.
θ = 35°μ = 0.2d = 3 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 2 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3.5 m long (μ = 0.15) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2 kgh = 4 mL = 3.5 mμ = 0.15k = 5000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 4 kg glider moving at 8 m/s makes a perfectly elastic head-on collision with a 5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 4 kgm2 = 5 kgv1 = 8 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 22 m/s and bounces straight back at 10 m/s. The contact lasts 10 ms. Find the average force Favg of the wall on the ball.
m = 0.5 kgvin = 22 m/svout = 10 m/sΔt = 10 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 220 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 25 mm siphons water from an open tank. The highest point C of the hose is 1.5 m above the water surface, and the outlet (open to the air) is 4.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 25 mmzC = +1.5 mz2 = −4.5 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
What volume V does 310 g of He occupy at 650 kPa and 40 °C? Treat it as an ideal gas.
A heat engine works between a hot reservoir at 525 °C and a cold reservoir at 30 °C. It takes in 4500 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 525 °CTL = 30 °CQH = 4500 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat engine takes in 1600 kJ of heat from a reservoir at 400 °C, produces 528 kJ of work and rejects the rest to a reservoir at 30 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 400 °CTL = 30 °CQH = 1600 kJW = 528 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
A source of 1000 Hz moving at 30 m/s and an observer moving at 10 m/s approach each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 1000 Hzv = 343 m/svs = 30 m/svo = 10 m/s
f′ = Hz
20.Waves, sound & opticsHard
Two slits 0.15 mm apart are lit with monochromatic light. On a screen 2 m away, bright fringe number 1 lies 6.4 mm from the central fringe. Find the wavelength λ.
d = 0.15 mmL = 2 my1 = 6.4 mmm = 1
λ = nm
3Solutions
1.Kinematics
Answer: v = 96.7 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·2.75·1700) = 96.7 m/s
Answer
v = 96.7 m/s
(348.1 km/h)
2.Kinematics
Answer: s = 972 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 3·12 = 36 m/s
Distance of each phase
s1 = ½·3·12² = 216 m
s2 = 36·12 = 432 m
s3 = 36²/(2·2) = 324 m
Total distance
s = 216 + 432 + 324 = 972 m
Answer
s = 972 m
3.Newton’s laws
Answer: a = 5.549 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 36·cos 45° = 25.46 m/s
vy = v0·sin θ = 36·sin 45° = 25.46 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·25.46/9.81 = 5.19 s
Horizontal distance
x = vx·t = 25.46·5.19 = 132.1 m
Answer
x = 132.1 m
6.Projectile motion
Answer: H = 63.03 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 12·sin 40° = 7.713 m/s
Rise above the cliff
Δh = vy²/(2g) = 7.713²/(2·9.81) = 3.032 m
Height above the ground
H = 60 + 3.032 = 63.03 m
Answer
H = 63.03 m
7.Work & energy
Answer: v = 4.911 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·3·(0.5736 − 0.2·0.8192)) = 4.911 m/s
Answer
v = 4.911 m/s
8.Work & energy
Answer: x = 16.51 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(4 − 0.15·3.5) = 68.18 J
Maximum compression
½kx² = 68.18 → x = √(2·68.18/5000) = 0.1651 m = 16.51 cm
Answer
x = 16.51 cm
9.Momentum & collisions
Answer: v′2 = 7.111 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4 − 5)/(4 + 5)·8 = −0.8889 m/s
v′2 = 2·4/(4 + 5)·8 = 7.111 m/s
Answer
v′2 = 7.111 m/s
10.Momentum & collisions
Answer: Favg = 1600 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(10 + 22) = 16 N·s
Average force
Favg = J/Δt = 16/0.01 = 1600 N
Answer
Favg = 1600 N
11.Hydrostatic force
Answer: F = 264.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 3/2 = 3 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·9 = 264.9 kN
Answer
F = 264.9 kN
12.Hydrostatic force
Answer: ycp = 3.595 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2/2 = 3.5 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·4 = 137.3 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 525 + 273.15 = 798.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/798.1 = 62.02 %
Maximum work
Wmax = ηmax·QH = 0.6202·4500 = 2791 kJ
Answer
Wmax = 2791 kJ
18.Heat engines & refrigerators
Answer: Sgen = 1.159 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 1600 − 528 = 1072 kJ
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
TL = 30 + 273.15 = 303.1 K
Entropy changes of the reservoirs
ΔSH = −1600/673.1 = −2.377 kJ/K
ΔSL = 1072/303.1 = 3.536 kJ/K
Sgen = 3.536 − 2.377 = 1.159 kJ/K
Answer
Sgen = 1.159 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: f′ = 1128 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …