Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 36 km/h sees an obstacle. Her reaction time is 1.5 s, after which the car brakes with a constant deceleration of 8 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 36 km/htr = 1.5 sa = −8 m/s²
d = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 20 m/s² for 3 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 20 m/s²t1 = 3 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 2 kg block slides down a frictionless slope at 20° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 2 kgθ = 20°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 0.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1.5 kgm2 = 0.5 kgμ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 35° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 40 m/sθ = 35°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is thrown from ground level at 23 m/s and 70° above the horizontal. It lands on the flat roof of a building 3 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 23 m/sθ = 70°hroof = 3 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.2. Find its speed v after it has slid 20 m along the slope.
θ = 25°μ = 0.2d = 20 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 10 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.1) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 10 kgh = 3 mL = 2 mμ = 0.1k = 1500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1.5 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 2 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 1.5 kgm2 = 2 kgv1 = 2 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
At a crossing a 900 kg car travelling east at 15 m/s collides with a 2000 kg car travelling north at 14 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 900 kgv1 = 15 m/s (E)m2 = 2000 kgv2 = 14 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal venturi meter with an inlet diameter of 300 mm and a throat diameter of 150 mm. The pressure at the inlet is 21 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 150 mm to 50 mm while rising 4 m. At section 1 the pressure is 170 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 625 °C and a cold reservoir at 25 °C. It takes in 4200 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 625 °CTL = 25 °CQH = 4200 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump delivers 9.5 kW of heat to a heating system at 55 °C, taking heat from a source at 5 °C. Its actual COP is 35% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 55 °CTL = 5 °CηII = 35%Q̇H = 9.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A string fixed at both ends is 0.65 m long; waves travel on it at 80 m/s. Find the frequency f5 of its harmonic number 5.
v = 80 m/sn = 5L = 0.65 m
f5 = Hz
20.Waves, sound & opticsHard
A diffraction grating has 400 lines per millimetre. Light of wavelength 532 nm falls on it at right angles. What is the highest order mmax of bright maximum that can be seen?
N = 400 mm⁻¹λ = 532 nm
mmax =
3Solutions
1.Kinematics
Answer: d = 21.25 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Reaction distance
d1 = v₀·tr = 10·1.5 = 15 m
Braking distance
d2 = v₀²/(2a) = 10²/(2·8) = 6.25 m
Total
d = 15 + 6.25 = 21.25 m
Answer
d = 21.25 m
2.Kinematics
Answer: hmax = 273.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 20·3 = 60 m/s
h₁ = ½·20·3² = 90 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 60²/(2·9.81) = 183.5 m
hmax = 90 + 183.5 = 273.5 m
Answer
hmax = 273.5 m
3.Newton’s laws
Answer: a = 3.355 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 40·cos 35° = 32.77 m/s
vy = v0·sin θ = 40·sin 35° = 22.94 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·22.94/9.81 = 4.677 s
Horizontal distance
x = vx·t = 32.77·4.677 = 153.3 m
Answer
x = 153.3 m
6.Projectile motion
Answer: x = 33.53 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 7.866 m/s, vy = 21.61 m/s
Time to land on the roof
Larger root: the ball is descending.
3 = 21.61·t − 4.905·t²
t = (21.61 + √(21.61² − 2·9.81·3))/9.81 = 4.263 s
Horizontal distance
x = vx·t = 7.866·4.263 = 33.53 m
Answer
x = 33.53 m
7.Work & energy
Answer: v = 9.732 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·20·(0.4226 − 0.2·0.9063)) = 9.732 m/s
Answer
v = 9.732 m/s
8.Work & energy
Answer: x = 60.52 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 98.1·(3 − 0.1·2) = 274.7 J
Maximum compression
½kx² = 274.7 → x = √(2·274.7/1500) = 0.6052 m = 60.52 cm
Answer
x = 60.52 cm
9.Momentum & collisions
Answer: v′1 = −0.2857 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1.5 − 2)/(1.5 + 2)·2 = −0.2857 m/s
v′2 = 2·1.5/(1.5 + 2)·2 = 1.714 m/s
Answer
v′1 = −0.2857 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: θ = 64.26 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 900·15 = 13500 kg·m/s
py = 2000·14 = 28000 kg·m/s
Direction
tan θ = py/px = 2.074 → θ = 64.26°
Answer
θ = 64.26°
11.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2/2 = 1.5 m
A = H·b = 2·3 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·6 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: ycp = 2.333 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2.25·3 = 83.43 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/300)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 625 + 273.15 = 898.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/898.1 = 66.8 %
Maximum work
Wmax = ηmax·QH = 0.668·4200 = 2806 kJ
Answer
Wmax = 2806 kJ
18.Heat engines & refrigerators
Answer: Ẇ = 4.136 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 55 + 273.15 = 328.1 K
TL = 5 + 273.15 = 278.1 K
Carnot and actual COP
COPmax = 328.1/(328.1 − 278.1) = 6.563
COP = 0.35·6.563 = 2.297
Power input
Ẇ = Q̇H/COP = 9.5/2.297 = 4.136 kW
Answer
Ẇ = 4.136 kW
19.Waves, sound & optics
Answer: f5 = 307.7 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.65/5 = 0.26 m
Frequency
f = v/λ = 80/0.26 = 307.7 Hz
Answer
f5 = 307.7 Hz
20.Waves, sound & optics
Answer: mmax = 4
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …