Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 45 km/h brakes with a constant deceleration of 7.5 m/s² until it stops. Find the braking distance s.
v₀ = 45 km/ha = −7.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 6 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 6 m/sh₀ = 35 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 6 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 6 kgθ = 45°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 1.5 kgm2 = 1 kgμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 32 m/s and must land 45 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 32 m/sR = 45 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 28 m/sθ = 45°h = 45 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 0.5 kg ball hangs on a light string of length 0.5 m. It is pulled aside until the string makes 40° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 0.5 kgL = 0.5 mθ = 40°g = 9.81 m/s²
T = N
8.Work & energyHard
A 4 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 5 m long (μ = 0.1) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 5 mL = 5 mμ = 0.1k = 4000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 10 g bullet is fired horizontally into a 1 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 6 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 1 kgh = 6 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.35 kg ball hits a wall at 15 m/s and bounces straight back at 6 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.35 kgvin = 15 m/svout = 6 m/sΔt = 20 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 2 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 2.5 mb = 1 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 280 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 150 mm to 100 mm while rising 5 m. At section 1 the pressure is 290 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 600 °C and a cold reservoir at 10 °C. Find the highest possible thermal efficiency ηmax.
TH = 600 °CTL = 10 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat engine takes in 4900 kJ of heat from a reservoir at 800 °C, produces 2156 kJ of work and rejects the rest to a reservoir at 20 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 800 °CTL = 20 °CQH = 4900 kJW = 2156 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
An object stands 18 cm in front of a thin converging lens with a focal length of 25 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 18 cmf = 25 cm
di = cm
20.Waves, sound & opticsHard
A parking sensor at rest sends ultrasound of 20 kHz towards a car that moves away at 30 m/s. Find the frequency f″ of the echo received back at the sensor (speed of sound 343 m/s).
f = 20 kHzu = 30 m/sv = 343 m/s
f″ = Hz
3Solutions
1.Kinematics
Answer: s = 10.42 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 45/3.6 = 12.5 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 12.5²/(2·7.5) = 10.42 m
Answer
s = 10.42 m
2.Kinematics
Answer: hmax = 36.83 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 6²/(2·9.81) = 1.835 m
Height above the ground
hmax = 35 + 1.835 = 36.83 m
Answer
hmax = 36.83 m
3.Newton’s laws
Answer: a = 6.243 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·45/32² = 0.4311
Angle
2θ = 25.54° → θ = 12.77°
Answer
θ = 12.77°
The other solution is 90° − θ = 77.23°.
6.Projectile motion
Answer: t = 5.658 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 45° = 19.8 m/s
vy = v0·sin θ = 28·sin 45° = 19.8 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 45 + 19.8·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (19.8 + √(392 + 882.9))/9.81 = 5.658 s
Answer
t = 5.658 s
7.Work & energy
Answer: T = 7.2 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·0.5·(1 − cos 40°) = 2.295 m²/s²
Forces at the bottom
m·g = 0.5·9.81 = 4.905 N
T = mg + mv²/L = 4.905 + 0.5·2.295/0.5 = 7.2 N
Answer
T = 7.2 N
Check: T = mg(3 − 2cos θ) = 7.2 N.
8.Work & energy
Answer: x = 29.71 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(5 − 0.1·5) = 176.6 J
Maximum compression
½kx² = 176.6 → x = √(2·176.6/4000) = 0.2971 m = 29.71 cm
Answer
x = 29.71 cm
9.Momentum & collisions
Answer: v = 109.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.06) = 1.085 m/s
Collision
m·v = (m + M)·V → v = (0.01 + 1)·1.085/0.01 = 109.6 m/s
Answer
v = 109.6 m/s
10.Momentum & collisions
Answer: J = 7.35 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.35·(6 + 15) = 7.35 N·s
Answer
J = 7.35 N·s
11.Hydrostatic force
Answer: F = 58.86 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·2 = 58.86 kN
Answer
F = 58.86 kN
12.Hydrostatic force
Answer: F = 91.72 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2.5/2 = 4.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·4.25·2.5 = 91.72 kN
Answer
F = 91.72 kN
13.Continuity & Bernoulli
Answer: p2 = 278.9 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 308.1 K, T2 = 323.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(150/350)·(323.1/308.1) = 8.989 L
Answer
V2 = 8.989 L
17.Heat engines & refrigerators
Answer: ηmax = 67.57 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 283.1/873.1 = 67.57 %
Answer
ηmax = 67.57 %
18.Heat engines & refrigerators
Answer: Sgen = 4.794 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 4900 − 2156 = 2744 kJ
Absolute temperatures
TH = 800 + 273.15 = 1073 K
TL = 20 + 273.15 = 293.1 K
Entropy changes of the reservoirs
ΔSH = −4900/1073 = −4.566 kJ/K
ΔSL = 2744/293.1 = 9.36 kJ/K
Sgen = 9.36 − 4.566 = 4.794 kJ/K
Answer
Sgen = 4.794 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: di = −64.29 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/25 − 1/18
di = −64.29 cm
Ray diagram
virtual, on the same side as the object
Answer
di = −64.29 cm
20.Waves, sound & optics
Answer: f″ = 16783 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.