Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 90 km/h sees an obstacle. Her reaction time is 0.8 s, after which the car brakes with a constant deceleration of 7.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 90 km/htr = 0.8 sa = −7.5 m/s²
d = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 20 m/s² for 2 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 20 m/s²t1 = 2 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 4 m/s and comes to rest after 2 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 4 m/sd = 2 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 100 N pulls the front 1 kg block; the 11 kg block is towed behind. The coefficient of kinetic friction is 0.25 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 11 kgm2 = 1 kgF = 100 Nμ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 25° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 34 m/sθ = 25°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 33 m/s and 20° above the horizontal from the top of a 55 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 33 m/sθ = 20°h = 55 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A car travelling at 40 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.6. Find the stopping distance d.
v = 40 km/hμ = 0.6g = 9.81 m/s²
d = m
8.Work & energyHard
A 5 kg block rests on a rough horizontal table (μ = 0.15). A light string runs from it over a smooth pulley at the edge of the table to a hanging 5 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1 m.
m1 = 5 kgm2 = 5 kgμ = 0.15d = 1 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 2.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 1 kgm2 = 2.5 kgv1 = 2 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 10 g bullet is fired horizontally into a 4 kg block hanging from light strings 1.1 m long, and stays in it. The strings swing out to a largest angle of 40° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 4 kgL = 1.1 mθ = 40°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 1 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of glycerin, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 140 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 300 mm, throat 150 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 350 mm. The discharge coefficient is 0.99. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A reversible refrigerator keeps a cold room at 2 °C by removing 10 kW of heat, and rejects heat to the surroundings at 35 °C. Find the rate Q̇H at which it rejects heat.
TL = 2 °CTH = 35 °CQ̇L = 10 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1100 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 35 °C. Both engines produce the same work. Find Tm in °C.
TH = 1100 °CTL = 35 °C
Tm = °C
19.Waves, sound & opticsMedium
A source of 440 Hz moving at 25 m/s and an observer moving at 5 m/s move away from each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 440 Hzv = 343 m/svs = 25 m/svo = 5 m/s
f′ = Hz
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.5 and a cladding with n₂ = 1.49. Find the largest angle θa to the fibre axis at which light from air can enter the end of the fibre and still be guided by total internal reflection.
n1 = 1.5n2 = 1.49n0 = 1.00
θa = °
3Solutions
1.Kinematics
Answer: d = 61.67 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Reaction distance
d1 = v₀·tr = 25·0.8 = 20 m
Braking distance
d2 = v₀²/(2a) = 25²/(2·7.5) = 41.67 m
Total
d = 20 + 41.67 = 61.67 m
Answer
d = 61.67 m
2.Kinematics
Answer: hmax = 121.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 20·2 = 40 m/s
h₁ = ½·20·2² = 40 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 40²/(2·9.81) = 81.55 m
hmax = 40 + 81.55 = 121.5 m
Answer
hmax = 121.5 m
3.Newton’s laws
Answer: μ = 0.4077
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 4²/(2·2) = 4 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 4/9.81 = 0.4077
Answer
μ = 0.4077
4.Newton’s laws
Answer: T = 91.67 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: t = 2.929 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 34·cos 25° = 30.81 m/s
vy = v0·sin θ = 34·sin 25° = 14.37 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·14.37/9.81 = 2.929 s
Answer
t = 2.929 s
6.Projectile motion
Answer: H = 61.49 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 33·sin 20° = 11.29 m/s
Rise above the cliff
Δh = vy²/(2g) = 11.29²/(2·9.81) = 6.493 m
Height above the ground
H = 55 + 6.493 = 61.49 m
Answer
H = 61.49 m
7.Work & energy
Answer: d = 10.49 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 40/3.6 = 11.11 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 11.11²/(2·0.6·9.81) = 10.49 m
Answer
d = 10.49 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 2.888 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 49.05·1 = 49.05 J
μ·m₁g·d = 0.15·49.05·1 = 7.357 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 41.69 → v = √(2·41.69/10) = 2.888 m/s
Answer
v = 2.888 m/s
9.Momentum & collisions
Answer: v′2 = 1.143 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1 − 2.5)/(1 + 2.5)·2 = −0.8571 m/s
v′2 = 2·1/(1 + 2.5)·2 = 1.143 m/s
Answer
v′2 = 1.143 m/s
10.Momentum & collisions
Answer: v = 901.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.1·(1 − cos 40°) = 0.2574 m
Speed after impact
V = √(2·9.81·0.2574) = 2.247 m/s
Collision
v = (m + M)·V/m = 4.01·2.247/0.01 = 901.1 m/s
Answer
v = 901.1 m/s
11.Hydrostatic force
Answer: F = 34.34 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1/2 = 3.5 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·1 = 34.34 kN
Answer
F = 34.34 kN
12.Hydrostatic force
Answer: ycp = 2.042 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1/2 = 2 m
A = H·b = 1·3 = 3 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2·3 = 74.16 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 3·1³/12 = 0.25 m⁴
ycp = yc + Ic/(yc·A) = 2 + 0.25/(2·3) = 2.042 m
Answer
ycp = 2.042 m
13.Continuity & Bernoulli
Answer: p2 = 135.4 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.35 = 43262 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 323.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(100/150)·(323.1/293.1) = 3.674 L
Answer
V2 = 3.674 L
17.Heat engines & refrigerators
Answer: Q̇H = 11.2 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 35 + 273.15 = 308.1 K
TL = 2 + 273.15 = 275.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 10·308.1/275.1 = 11.2 kW
Answer
Q̇H = 11.2 kW
Power input: Ẇ = 1.199 kW.
18.Heat engines & refrigerators
Answer: Tm = 567.5 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1100 + 273.15 = 1373 K
TL = 35 + 273.15 = 308.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1373 + 308.1)/2 = 840.7 K = 567.5 °C
Answer
Tm = 567.5 °C
19.Waves, sound & optics
Answer: f′ = 404.1 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.