Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 5.5 m/s² until it stops. Find the braking distance s.
v₀ = 108 km/ha = −5.5 m/s²v = 0
s = m
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 2.8 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 2.8 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 11.5 m/s and comes to rest after 45 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 11.5 m/sd = 45 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
An 8.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5.5 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 8.5 kgm2 = 5.5 kgμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 50° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 10 m/sθ = 50°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is thrown from ground level at 34 m/s and 60° above the horizontal. It lands on the flat roof of a building 4 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 34 m/sθ = 60°hroof = 4 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 9 m along the slope.
θ = 25°μ = 0.15d = 9 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 10 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.2) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 10 kgh = 4 mL = 2 mμ = 0.2k = 500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 4.5 kg glider moving at 3 m/s makes a perfectly elastic head-on collision with a 4 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 4.5 kgm2 = 4 kgv1 = 3 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
At a crossing a 900 kg car travelling east at 24 m/s collides with a 1400 kg car travelling north at 15 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 900 kgv1 = 24 m/s (E)m2 = 1400 kgv2 = 15 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 200 mm to 75 mm. In the wide section the pressure is 120 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 50 mm and a gauge pressure of 130 kPa. The nozzle exit diameter is 25 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine receives heat from a source at 550 °C and rejects heat to the surroundings at 35 °C. Its actual thermal efficiency is 44%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 550 °CTL = 35 °Cη = 44%
ηII = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is 5 °C outside, delivering 6 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 21 °CTL = 5 °CQ̇H = 6 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 6 cm in front of a thin diverging lens with a focal length of 30 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 6 cmf = −30 cm
di = cm
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.46 and a cladding with n₂ = 1.41. Find the largest angle θa to the fibre axis at which light from air can enter the end of the fibre and still be guided by total internal reflection.
n1 = 1.46n2 = 1.41n0 = 1.00
θa = °
3Solutions
1.Kinematics
Answer: s = 81.82 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 30²/(2·5.5) = 81.82 m
Answer
s = 81.82 m
2.Kinematics
Answer: d = 35.65 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(2.8 − t₁)
4.905·t₁² + 343·t₁ − 960.4 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·960.4))/(2·4.905) = 2.696 s
Depth
d = ½·9.81·2.696² = 35.65 m
Answer
d = 35.65 m
3.Newton’s laws
Answer: μ = 0.1498
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 11.5²/(2·45) = 1.469 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 1.469/9.81 = 0.1498
Answer
μ = 0.1498
4.Newton’s laws
Answer: a = 2.067 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 10·cos 50° = 6.428 m/s
vy = v0·sin θ = 10·sin 50° = 7.66 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·7.66/9.81 = 1.562 s
Horizontal distance
x = vx·t = 6.428·1.562 = 10.04 m
Answer
x = 10.04 m
6.Projectile motion
Answer: x = 99.69 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 17 m/s, vy = 29.44 m/s
Time to land on the roof
Larger root: the ball is descending.
4 = 29.44·t − 4.905·t²
t = (29.44 + √(29.44² − 2·9.81·4))/9.81 = 5.864 s
Horizontal distance
x = vx·t = 17·5.864 = 99.69 m
Answer
x = 99.69 m
7.Work & energy
Answer: v = 7.115 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·9·(0.4226 − 0.15·0.9063)) = 7.115 m/s
Answer
v = 7.115 m/s
8.Work & energy
Answer: x = 118.9 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 98.1·(4 − 0.2·2) = 353.2 J
Maximum compression
½kx² = 353.2 → x = √(2·353.2/500) = 1.189 m = 118.9 cm
Answer
x = 118.9 cm
9.Momentum & collisions
Answer: v′2 = 3.176 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4.5 − 4)/(4.5 + 4)·3 = 0.1765 m/s
v′2 = 2·4.5/(4.5 + 4)·3 = 3.176 m/s
Answer
v′2 = 3.176 m/s
10.Momentum & collisions
Answer: v′ = 13.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1/2 = 2 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·1 = 19.62 kN
Answer
F = 19.62 kN
12.Hydrostatic force
Answer: F = 264.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 3/2 = 4.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.5·6 = 264.9 kN
Answer
F = 264.9 kN
13.Continuity & Bernoulli
Answer: p2 = 113.8 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 25/50 = 0.5
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·130000/(1000·0.9375)) = 16.65 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 16.65²/(2·9.81) = 14.14 m
Answer
H = 14.14 m
15.Ideal gas law
Answer: P = 5241 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 500/28.01 = 17.85 mol
T = 80 + 273.15 = 353.1 K
Pressure
P = nRT/V = 17.85·8.314·353.1/0.01 = 5241 kPa
Answer
P = 5241 kPa
16.Ideal gas law
Answer: ρ = 6.101 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 200 + 273.15 = 473.1 K
Density
ρ = 750·32/(8.314·473.1) = 6.101 kg/m³
Answer
ρ = 6.101 kg/m³
17.Heat engines & refrigerators
Answer: ηII = 70.33 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηCarnot = 1 − 308.1/823.1 = 62.56 %
Second-law efficiency
ηII = η/ηCarnot = 44/62.56 = 70.33 %
Answer
ηII = 70.33 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.3264 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 6/18.38 = 0.3264 kW
Answer
Ẇmin = 0.3264 kW
19.Waves, sound & optics
Answer: di = −5 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−30) − 1/6
di = −5 cm
Ray diagram
virtual, on the same side as the object
Answer
di = −5 cm
20.Waves, sound & optics
Answer: θa = 22.26 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.