Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 24 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 2.5 m/s². How long does it take the police car to catch up? Find t.
vcar = 24 m/sapolice = 2.5 m/s²v0,police = 0
t = s
2.KinematicsHard
Ball A is dropped from rest from a height of 15 m. At the same instant ball B is thrown straight up from the ground directly below at 10 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 15 mv0B = 10 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 2 kg block slides down a frictionless slope at 45° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 2 kgθ = 45°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 6.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 6.5 kgm2 = 2 kgμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 15° above the horizontal and lands 105 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 15°R = 105 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 24 m/s and 45° above the horizontal from the top of a 50 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 24 m/sθ = 45°h = 50 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A car travelling at 50 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 50 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A 4 kg block is released from rest at height 2.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.3) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 2.5 mL = 3 mμ = 0.3k = 5000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 10 g bullet is fired horizontally into a 3 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 3 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 3 kgh = 3 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 12 g bullet is fired horizontally into a 5 kg block hanging from light strings 1.8 m long, and stays in it. The strings swing out to a largest angle of 10° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 5 kgL = 1.8 mθ = 10°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 2 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal venturi meter with an inlet diameter of 150 mm and a throat diameter of 100 mm. The pressure at the inlet is 51 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 200 mm to 100 mm while rising 5 m. At section 1 the pressure is 220 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 200 °C and a cold reservoir at 30 °C. Find the highest possible thermal efficiency ηmax.
TH = 200 °CTL = 30 °C
ηmax = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 800 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 30 °C. Both engines have the same thermal efficiency. Find Tm in °C.
TH = 800 °CTL = 30 °C
Tm = °C
19.Waves, sound & opticsMedium
A string fixed at both ends is 1.5 m long; waves travel on it at 80 m/s. Find the frequency f3 of its harmonic number 3.
v = 80 m/sn = 3L = 1.5 m
f3 = Hz
20.Waves, sound & opticsHard
Light of wavelength 656 nm falls at right angles on a grating with 600 lines per millimetre. Find the angle θ2 of the order-2 maximum.
N = 600 mm⁻¹λ = 656 nmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: t = 19.2 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·24/2.5 = 19.2 s
Answer
t = 19.2 s
At that moment the police car moves at 2v = 48 m/s.
2.Kinematics
Answer: t = 1.5 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
15 − ½g·t² = 10·t − ½g·t² → t = 15/10 = 1.5 s
Answer
t = 1.5 s
3.Newton’s laws
Answer: a = 6.937 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·105/sin 30°) = 45.39 m/s
Answer
v0 = 45.39 m/s
6.Projectile motion
Answer: v = 39.46 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 24·cos 45° = 16.97 m/s
vy0 = 24·sin 45° = 16.97 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(16.97² + 2·9.81·50) = 35.62 m/s
Impact speed
v = √(16.97² + 35.62²) = 39.46 m/s
Answer
v = 39.46 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: d = 14.05 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 50/3.6 = 13.89 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 13.89²/(2·0.7·9.81) = 14.05 m
Answer
d = 14.05 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: x = 15.85 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(2.5 − 0.3·3) = 62.78 J
Maximum compression
½kx² = 62.78 → x = √(2·62.78/5000) = 0.1585 m = 15.85 cm
Answer
x = 15.85 cm
9.Momentum & collisions
Answer: v = 230.9 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.03) = 0.7672 m/s
Collision
m·v = (m + M)·V → v = (0.01 + 3)·0.7672/0.01 = 230.9 m/s
Answer
v = 230.9 m/s
10.Momentum & collisions
Answer: v = 305.9 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.8·(1 − cos 10°) = 0.02735 m
Speed after impact
V = √(2·9.81·0.02735) = 0.7325 m/s
Collision
v = (m + M)·V/m = 5.012·0.7325/0.012 = 305.9 m/s
Answer
v = 305.9 m/s
11.Hydrostatic force
Answer: F = 39.24 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2/2 = 2 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·2 = 39.24 kN
Answer
F = 39.24 kN
12.Hydrostatic force
Answer: F = 83.43 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2.25·3 = 83.43 kN
Answer
F = 83.43 kN
13.Continuity & Bernoulli
Answer: Q = 88.55 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(100/150)² = 0.4444·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 413.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(250/800)·(413.1/288.1) = 2.24 L
Answer
V2 = 2.24 L
17.Heat engines & refrigerators
Answer: ηmax = 35.93 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 200 + 273.15 = 473.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/473.1 = 35.93 %
Answer
ηmax = 35.93 %
18.Heat engines & refrigerators
Answer: Tm = 297.2 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 800 + 273.15 = 1073 K
TL = 30 + 273.15 = 303.1 K
Equal efficiencies
1 − Tm/TH = 1 − TL/Tm gives Tm² = TH·TL.
Tm = √(1073·303.1) = 570.4 K = 297.2 °C
Answer
Tm = 297.2 °C
19.Waves, sound & optics
Answer: f3 = 80 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·1.5/3 = 1 m
Frequency
f = v/λ = 80/1 = 80 Hz
Answer
f3 = 80 Hz
20.Waves, sound & optics
Answer: θ2 = 51.92 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …